|
|
Headset adjustment... by
Graham Triggs
Hi, when I pull on the front brake, and rock the bike forwards and
backwards there is a tiny movement of about 2mm inside the headset.
I'm running a marzocchi...
|
|
2 |
372 |
|
|
Dura-Ace 10 shifting problem by
Larry Coon
'04 Trek OCLV with Dura-Ace 10, 53-39 & 11-23.
The drivetrain has about 500 miles on it, and
the chain was cleaned & re-lubed about a week
ago.
The RD...
|
|
7 |
350 |
|
|
Speedplay Cleat lubricant by
Jee Doy
I tried White Lightening on the cleats and it seems to allow me to snap in and
out of the pedals easily. Are there any disadvantages?
( 1 2 3)
|
January 19th 05 05:59 PM
by Mark
|
21 |
1,284 |
|
|
Ultegra 10 speed triple trim setting by
Mike DeMicco
I'm having difficulty with the trim setting on the middle ring. If I try
to trim the middle ring, it just shifts to the inner ring. It seems that
the trim...
|
|
0 |
615 |
|
|
bike lights question - follow up by
marco007esq
Wow, there were a LOT of helpful responses to my original question.
Thank you to everyone.
Some asked what the lights in question would be used for... and...
( 1 2)
|
|
16 |
818 |
|
|
Vintage Trek Restoration Q: Decals by
bigsky
I am upgrading my 1986 Trek 400D and looking at restoration as needed.
One problem I have is a plastic chainstay covers a decal and it has
bubbles and is...
|
January 19th 05 04:29 AM
by bigsky
|
0 |
1,044 |
|
|
Question on Bike Lights by
marco007esq
After spending years using crappy lights, I finally am fed up and ready
to drop serious money on SERIOUS lights.
The problem is, I hate to spend $200-$500 to...
( 1 2 3 ... Last Page)
|
|
34 |
1,423 |
|
|
after the new handlebar--problems by
Pat
After I put on the new handlebar, I noticed that it must be about 1-2 inches
wider than the old one and this made the cables shorter. So, I removed some
of...
|
|
2 |
257 |
|
|
bolt extraction by
j morelstein
My trainer (a Cateye cyclosimulator 3000) has two legs in the front which
are bolted with two machine bolts to the body of the trainer. One of the
bolts has...
( 1 2)
|
|
10 |
558 |
|
|
Tufo installation by
Goldy
How does one go about fitting one of those tubular
clincher tires on to a rim? I sent close to an hour
the other night with no success. Contis are...
( 1 2)
|
|
11 |
504 |
|
|
LIQUIDATION? nASHBAR? by
Bill Sornson
wrote:
LIQUIDATION MEANS: TERMINATION, AN ENDING OF BUSINESS, FINI, NO MORE
NO MORE!
is this correct?
or are the nbar folks havin'...
( 1 2 3 ... Last Page)
|
|
38 |
1,200 |
|
|
Michelin's new "Tweel" by
[email protected]
Source:
http://www.michelinman.com/difference/releases/pressrelease01102005a.html
MICHELIN LETS THE AIR OUT OF FUTURE TIRE INNOVATION
Michelin announces two...
|
January 19th 05 12:15 AM
by Chalo
|
4 |
1,077 |
|
|
Shorter top tube? by
tuben
I seem to have long legs in relation to upper body,
and have some difficulty in getting a comfortable
position on my road bike which is a Bianchi.
The saddle...
( 1 2 3 ... Last Page)
|
January 18th 05 11:28 PM
by Ningi
|
36 |
1,224 |
|
|
Disk vs V: Weight? by
(Pete Cresswell)
I just swapped my rear Avid mech out for a Shimano Deore XT V brake.
Weighed the V plus cable against the Avid plus cable plus rotor, found a diff of
110g -...
|
|
4 |
216 |
|
|
|
|
9 |
397 |
|
|
|
|
0 |
175 |
|
|
|
|
0 |
247 |
|
|
Rebending steel dropouts by
meb
I had my rder shatter a hole in my plastic spoke protector as it went
through it enroute to getting trapped in my spokes. Not sure if the
freewheel bearings...
( 1 2 3)
|
|
23 |
976 |
|
|
I need nice slick cable housing by
Steve Knight
My recumbent needs some slick housing for good rear RD shifting. It came with
the cheap shimano crap that uses the plastic ends. Will just upgrading to the
top...
|
|
9 |
442 |
|
|
|
|
6 |
269 |