|
|
|
|
6 |
635 |
|
|
|
|
34 |
1,850 |
|
|
bearing cones by
Gregory McGuire
when regreasing bearing cones, how tight should the cones be tightened
against the bearings.
the way I did it was to tighten finger tight and back off some....
|
August 13th 04 02:19 AM
by Mark
|
4 |
570 |
|
|
Cassette Lockring slipping? by
Alan Hoyle
Every time I've tried to install or remove a Shimano/SRAM style
cassette lockring, I've had a lot of trouble actually getting it to
work. Inevitably, the...
|
August 13th 04 02:13 AM
by hobby
|
6 |
615 |
|
|
|
|
4 |
958 |
|
|
Japanese 3-speeds by
Mike
Browsing around ebay recently I came across a Nishiki 3-speed
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=3693189560
The photo is not that great,...
|
August 12th 04 11:22 PM
by A Muzi
|
4 |
670 |
|
|
Which indoor trainer by
Marcus I. Valdes
I know it's a little early in the year to be talking about this, but
which indoor trainer do you guys use/like? I've seen the Giant Tempo
at the LBS, and it...
|
|
7 |
456 |
|
|
|
|
5 |
495 |
|
|
7 speed freewheel on 6 speed hub by
Sugob
I've read info at various sites about 6 & 7 speed freewheels (not
cassettes) being practically interchangeable on a bike built for a 6
speed FW. Has anyone...
|
|
3 |
1,520 |
|
|
Gripshifters at 40,000 miles. by
charles ramsey
First thing you do take the mounting screws all the way out and put
some grease on them this will save you a lot of grief later on. They
still work even though...
|
|
0 |
284 |
|
|
Nokon Housing and Shimano by
Sheldon K. Smith
Has anyone used Nokon housing with Shimano DuraAce levers? I noticed
on the Nokon website (www.nokonusa.com) that Nokon has two versions of
shifter housing...
|
|
3 |
356 |
|
|
Rear axle and spacers by
DaveB
Need advice from anyone used to workign with wheels. I snapped an axle
and did some other damage to a rear wheel on my MTB. I swapped my
casette ( a 5 speed...
|
|
4 |
479 |
|
|
DIY Derailer Alignment by
Kyle.B.H
My wife likes to fall over on her bike, while standing still, to the right,
landing on the rear derailer. While I do replace the hanger whenever it
gets bent,...
|
|
7 |
531 |
|
|
|
|
2 |
1,079 |
|
|
Is Ultegra for big Guys? by
big Pete
Hi all,
One of my friends said that the Ultegra group does not have the tank
like qualities I will need from the components, and recommended me
getting 105s...
( 1 2 3)
|
|
24 |
1,499 |
|
|
Nokon Users....... by
Ryan Bates
hi, any opinions on Nokon cables from those of you who have tried
them? i know they're not cheap, but if worth the money i don't mind.
just looking for...
|
|
3 |
282 |
|
|
Problems with Altus derailleur pulley by
Elias
The upper pulley of my rear derailleur is too close to the cogs, and
sometimes it seems to be coming in contact with the same (with a bang,
apparently).
I have...
|
|
2 |
336 |
|
|
|
|
8 |
581 |
|
|
A scary experience by
Hjalmar Duklęt
I've had som squeacking noice coming from the front of my bike for quite
some time but have not been able to figure out where it came from or what
caused it....
( 1 2)
|
|
12 |
757 |
|
|
Chainring wear. by
Callistus Valerius
I notice when I'm only on the big ring, and I'm pushing a big gear, I feel
an occasional clicking in my feet thru the pedals. I don't think it's the
bottom...
|
|
7 |
259 |