|
|
|
|
29 |
1,742 |
|
|
Deep (or "long") Chainring Nuts (?) by
!Jones[_2_]
Hello,
I have a... well, strange... application wherein the chain line
requires a chainring nut with lots of thread; let's call it 16mm or
so.
Sometimes,...
( 1 2)
|
|
13 |
825 |
|
|
|
|
7 |
307 |
|
|
|
|
0 |
223 |
|
|
ISO standard for disk brake mounts by
!Jones[_2_]
Anyone have a link to a page with detailed dimensions on disk brake
mounting so that I can easily mill a jig?
I'm upgrading an old Santana tandem to a disk...
|
|
8 |
2,617 |
|
|
Disc rotors on older, threaded hubs? by
!Jones[_2_]
I'm planning on mounting a stoker-actuated disc on an older-model
tandem with a '70s-era Phil hub threaded for the Arya (sp?) drum unit.
That's the same thread...
|
May 31st 10 08:13 PM
by Chalo
|
2 |
387 |
|
|
|
December 13th 10 02:34 AM
by Mark J.
|
1 |
269 |
|
|
JIS Standard Vs "Low Profile" crank tapers by
!Jones[_2_]
I have an old bike long since converted to a "fixie". He's a solid
old machine with well over 100K behind him. The original "cup & cone"
BB is simply worn...
|
|
3 |
498 |
|
|
Pre-indexing (friction) thumb shifters. by
!Jones[_2_]
Along with the advent of the "mountain bike" came indexing (SIS, et.
al.) shifters. There was a brief time period in the mid-'80s where
this type of bicycle...
( 1 2)
|
|
18 |
3,385 |
|
|
Load carrying devices. by
!Jones[_3_]
In your opinion, what are the best rigs for carrying significant loads
by pedal power? By "load", I mean a shopping cart with a week's
supply of groceries or...
( 1 2 3 ... Last Page)
|
|
39 |
2,046 |
|
|
Shifters for handicapped riders? by
!Jones[_3_]
Hello,
I'm setting up a Lightfoot tricycle for a handicapped rider. In
addition to balance issues, she has very limited use of her right
hand. The Lightfoot...
|
|
4 |
339 |
|
|
Dry Chain Lube? by
!Jones[_3_]
I bought a container of dry chain lubricant thinking I was getting
generic tenacious oil; however, it looks like water. What is it?
It's dry chain...
|
|
5 |
710 |
|
|
Problem Solvers '06 Backstops by
!Jones[_3_]
Anybody know where I can get a couple of Problem Solvers backstops in
the single cable ('06) model? In '07, they went to a double cable and
it won't fit my...
|
|
0 |
367 |
|
|
Wendy's new recumbent cycle by
!Jones[_3_]
Well, it was a long wait; however, Wendy *loves* her new wheel. She's
built by Lightfoot Cycles near Missoula, Montana. Wendy is balance...
err... is...
( 1 2)
|
|
11 |
915 |
|
|
Matters of vintage Dura Ace taper? by
!Jones[_3_]
Dura Ace used the JIS taper, or so I have always believed. I'm
converting a nice, '83 vintage frame to a fixee. It has the old Dura
Ace AX group with that...
|
|
8 |
730 |
|
|
Nu-Vinci Hubs? Anyone have any experience? by
!Jones[_3_]
These things are relatively new. They're a variable-ratio hub. I
assume that the highest setting is direct drive and that they reduce
from there.
Has anyone...
|
|
9 |
612 |
|
|
Yo... Chalo by
!Jones[_4_]
On Fri, 10 Jul 2009 13:52:17 -0700 (PDT), in rec.bicycles.tech Chalo
wrote:
That 17" tall handlebar can be ordered by any bike shop...
|
|
6 |
677 |
|
|
Extended stems by
!Jones[_4_]
I am building up an old, 20" tandem for touring. It's way too small
for an adult, so I machined an extension for the goose neck... this
proved to be a poor...
( 1 2 3 ... Last Page)
|
|
294 |
5,707 |
|
|
Chain Cases by
!Jones[_6_]
Has anyone had any experience with a chain case?
We were in Dublin last summer and rented a tandem with full cases...
both the timing chain and drive chain...
( 1 2)
|
|
13 |
723 |
|
|
A generat question on TT levers. by
!Jones[_7_]
Can the "reverse" or TT levers be used effectively in an installation
where the rider's thumb points away from the lever's fulcrum?
I have never used them,...
|
|
4 |
281 |