|
|
|
|
1 |
650 |
|
|
|
|
11 |
1,082 |
|
|
Wheel truing question by
psycholist
I have a relatively new, custom-built wheel. Wheelsmith XL14/17/14
spokes (24) laced radially to a Speedcific hub and a Velocity Aerohead rim.
The wheel...
|
|
3 |
875 |
|
|
Damaged thread: anything to do about it? by
Per Löwdin
I got a small damage on my hub´s thread, on an interior axle, it is very
slight, most of the thread is OK. Is it possible to fix or do I have to buy
a new...
|
|
4 |
622 |
|
|
Removing Cartridge Bearings by
rogerwinn
I'm looking to get some grease behind my cartridge bearing Mavic Primat
Hubs (and I guess on a side note, why does Mavic put in the cartridg
bearings dry?),...
|
|
3 |
976 |
|
|
|
February 29th 04 08:53 PM
by ari
|
1 |
1,082 |
|
|
|
February 29th 04 03:35 AM
by HKEK
|
0 |
1,764 |
|
|
Pumping up tire on disc - how much pressure? by
Jens Kurt Heycke
I've been using one of those little L-shaped attachments on
my floor pump to pump up the tire on my disc. I get it up
to where the pump reads 60lbs and it...
|
|
5 |
953 |
|
|
mavic rims suck? by
Steve Knight
I had a mavic ma3 rim 36 spoke with good spokes on a campy hub on the rear.
now I am a heavy rider (right now about 238 with up to 15 or so pounds on my
back....
( 1 2 3 ... Last Page)
|
|
362 |
14,736 |
|
|
Cannondale R400 Sport as a commuter? by
Narayan Krishnamoorthy
Hello...
I am considering getting a Cannondale R400 Sport, with the triple, as a
commuter. I have a few questions about fender/tire clearance. I am looking
at...
|
|
2 |
1,301 |
|
|
|
|
28 |
1,787 |
|
|
YST threadless headsets by
Ian Szekeres
I really would like to use a quill stem on my newly purchased bike,
unfortunately it uses a threadless headset system. Since I am just
starting to ride again...
|
February 25th 04 09:30 AM
by A Muzi
|
5 |
3,830 |
|
|
cleat to pedal spindle distance? by
David Auker
Question: Anyone know of a chart documenting various shoe-cleat to
pedal-spindle distances for various pedals? Just curious, as I have a
saddle height using...
|
|
4 |
558 |
|
|
|
|
3 |
1,393 |
|
|
GameBike info by
Mark Vieselmeyer
Does anyone here have experience with GameBike? How do you like it? What
games do you like? Do any of the games allow variable speed controlled by
your...
|
February 25th 04 03:17 AM
by RWM
|
5 |
265 |
|
|
Noisy Rolfs by
BBear505
I'm sure this has been asked before, but how can I get into the freehub off
some Rolf Vector Pros so that I can grease that noisy freehub? I remember
seeing a...
|
|
9 |
672 |
|
|
|
|
12 |
1,015 |
|
|
Rolf Vector Pro question by
Kurd
Was planning on removing my 105 level cassette to throw in the parts washer
today after the store closed and everyone left, when disaster occured. I got
the...
|
|
1 |
382 |
|
|
Epic or Scalpel? by
Trukweaz
I am thinking of a new bike for 2004. I am going for either a s-works fsr/epic
or a scalpel 4000. Any thoughts on preference? Thanks in advance.
Kurt
|
|
3 |
314 |
|
|
Spoke Length Calculator by
bicyclette
Anybody know of a good online spoke length calculator?
I'm going with Vel. Deep V rim and suitable hub for the rear.
( 1 2)
|
|
16 |
1,328 |