A Cycling & bikes forum. CycleBanter.com

Go Back   Home » CycleBanter.com forum » rec.bicycles
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Post New Thread
Threads in Forum : Techniques Forum Tools Search this Forum Feed Icon
  Thread / Thread Starter Last Post Reverse Sort Order Replies Views
torque wrench issues by [email protected]
On Sat, 22 Apr 2017 02:24:50 +0200, Emanuel Berg wrote: I finally got the 1/2" torque wrench, 28-210 Nm, not even made in China, but...
8 230
torque wrench issues by Andrew Chaplin
Emanuel Berg wrote in : (Nm as well as "FT-LB", some English unit I take...
(Multi-page thread 1 2 3)
Today 05:02 AM
by John B Slocomb Go to last post
27 239
torque wrench issues by Benderthe.evilrobot
"Emanuel Berg" wrote in message ... I finally got the 1/2" torque wrench, 28-210 Nm, not even made in...
(Multi-page thread 1 2)
Today 05:02 AM
by John B Slocomb Go to last post
15 127
Blowing tube descending by [email protected]
In the flatlands we never worry about this stuff but still seems unreal you could blow a tire by overheating the rims. How long does the descent need to be...
(Multi-page thread 1 2 3 ... Last Page)
Today 02:43 AM
by Frank Krygowski[_4_] Go to last post
41 675
Shimano Brifter hoods by John B Slocomb
My utility bike has Shimano STi shifters and the hoods are deteriorating. Getting all sticky and falling apart. Are replacement hoods available (at a...
Today 01:42 AM
by John B Slocomb Go to last post
3 85
SLIME TODAY by [email protected]
The Shack gallery hosts a Great North West Mex Art show. We need Räikkönen's opinion. The measure is Dircksenian. meant for a political blog. The Fed would...
1 217
Cartridge bottom brackets by John B.[_3_]
I'm thinking of replacing the old three piece BB on one of my bikes with a Shimano cartridge bearing and I see that Shimano markets a UN-26 and UN-55...
(Multi-page thread 1 2 3 ... Last Page)
Yesterday 09:23 PM
by AMuzi Go to last post
89 1,013
Getting into and out of streamliner recumbents by [email protected]
Interestingly enough a normal recumbent three wheeler is hard to get on and off of perhaps the two wheelers are easier. But I can hardly picture how you would...
(Multi-page thread 1 2 3 ... Last Page)
Yesterday 08:21 PM
by Joerg[_2_] Go to last post
80 983
Mechanical Efficiency by [email protected]
I have been looking all over the Internet to find comparisons of mechanical efficiency and haven't found anything that isn't covered in different units of...
(Multi-page thread 1 2 3)
28 339
torque wrench issues by John B Slocomb
On Sat, 22 Apr 2017 02:24:50 +0200, Emanuel Berg wrote: I finally got the 1/2" torque wrench, 28-210 Nm, not even made in China, but...
April 23rd 17 08:57 PM
by jbeattie Go to last post
4 217
Selecting An Appropriate Bolt by Art Shapiro
I had a bit of an adventure when one of the two handlebar-fixing bolts on my Deda Murex quilled stem decided to snap with a rather impressive cracking noise....
(Multi-page thread 1 2 3 ... Last Page)
98 1,124
Well, at least we haven't had landslides or cougar encounters by Andrew Chaplin
As Spring unfolds in Ottawa, it is getting in the way of my riding in spots. http://preview.tinyurl.com/NCCflooding -- Andrew Chaplin SIT MIHI GLADIUS SICUT...
April 23rd 17 07:48 PM
by Jeff Liebermann Go to last post
3 143
Cog Spacing by [email protected]
I've been thinking about it - is there any difference in the cog spacing between Shimano 10 speed and Campy?
1 166
Pentasport issues by Emanuel Berg[_2_]
On the Torpedo Pentasport (5 gear) bikes, there are often two small loop holes (?) on the chain stays to direct the wires. They remind of the same things on a...
April 22nd 17 06:02 PM
by AMuzi Go to last post
9 219
Habanero shows up curved stays by [email protected]
Ok my Habby shows up and beautiful Ti. I got the model with the curved stays as opposed to straight. I was surprised by the large curves in chain and seat...
(Multi-page thread 1 2 3 ... Last Page)
April 21st 17 03:56 PM
by Joerg[_2_] Go to last post
387 1,983
California risk by AMuzi
Hey Joerg: http://ktla.com/2017/04/17/mountain-lion-walks-into-norcal-bedroom-where-mom-and-child-were-sleeping-snatches-small-dog/ -- Andrew Muzi ...
7 519
Di2 multishift issues - Setup 6770 with external battery and old Junct-A by ixiz
I had issues with setting up a friends bike to do multishift and change the speed of shifting using the PCE-1 hardware. I was able to upload all the new...
3 188
Guess I need disc brakes. ;) by Sir Ridesalot
Was out riding some ofthe more technical trails in a local preserve today. then it started to rain and surprisingly enough my cantilever brakes started to fail...
April 19th 17 11:44 PM
by sms Go to last post
1 277
another danger of cycling by AMuzi
http://nypost.com/2017/04/13/last-cocaine-cowboy-arrested-after-26-years-in-hiding/ "Deputy marshals nabbed Gustavo Taby Falcon, 55, and his wife Amelia at...
7 829
Ok metal wizards by [email protected]
Could be a bike cable problem but actually a guitar string problem. In another life I repair guitars and play them. I hold a thought give I see this...
4 480
Post New Thread


Display Options
Showing threads 1 to 20 of 25163
Sorted By Sort Order
From The
Forum Tools Search this Forum
Search this Forum :

Advanced Search

New posts New posts More than 15 replies or 150 views Hot thread with new posts
No new posts No new posts More than 15 replies or 150 views Hot thread with no new posts
Closed Thread Thread is closed  
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 09:42 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 2004-2017 CycleBanter.com.
The comments are property of their posters.