View Single Post
  #5  
Old October 29th 04, 07:11 AM
Mike Iglesias
external usenet poster
 
Posts: n/a
Default

Archive-name: bicycles-faq/part5

[Note: The complete FAQ is available via anonymous ftp from
draco.acs.uci.edu (128.200.34.12), in pub/rec.bicycles.]

------------------------------

Subject: 9.12 Studded Tires
From: Name removed by request

[A summary on studded tires compiled by a reader. A complete copy of
the responses she received, including some that give directions for
making your own studded tires, is in the archive.]

Studded tires do help, especially on packed snow and ice. On fresh snow
and on water mixed with snow (i.e. slush) they're not significantly different
from unstudded knobbies.

On dry pavement they are noisy and heavy, but can be used; watch out for
cornering, which is degraded compared to unstudded tires.

Several people recommend a Mr. Tuffy or equivalent with them; one
respondent says he gets more flats with a liner than without.

In the U.S. the IRC Blizzard tires are commercially available. They
can also be made.

------------------------------

Subject: 9.13 Cycling Myths

Following are various myths about cycling and why they are/aren't true.


Myth: Wearing a helmet makes your head hotter than if you didn't wear one.

Actual measurements under hard riding conditions with ANSI standard
helmets show no consistent temperature difference from helmetless
riders. Part of the reason is that helmets provide insulated
protection from the sun as well as some airflow around the head.
(Les Earnest )


Myth: You need to let the air out of your tires before shipping your bike
on an airplane - if you don't, the tires will explode.

Assume your tire at sea level, pumped to 100 psi. Air pressure at sea
level is (about) 15psi. Therefore, the highest pressure which can be
reached in the tire is 100+15=115psi. Ergo: There is no need to
deflate bicycle tires prior to flight to avoid explosions.
(Giles Morris
)
Addendum: The cargo hold is pressurized to the same pressure as the
passenger compartment.
(Tom ?
)


Myth: You can break a bike lock with liquid nitrogen or other liquified gases

Freon cannot cool the lock sufficiently to do any good. Steel
conducts heat into the cooling zone faster than it can be removed by a
freeze bomb at the temperatures of interest. Liquid nitrogen or other
gasses are so cumbersome to handle that a lock on a bike cannot be
immersed as it must be to be effective. The most common and
inconspicuous way to break these locks is by using a 4 inch long 1
inch diameter commercial hydraulic jack attached to a hose and pump
unit.
(Jobst Brandt
)

[More myths welcome!]

------------------------------

Subject: 9.14 Descending I
From: Roger Marquis

[More up to date copies of Roger's articles can be found at
http://www.roble.com/marquis/]

Descending ability, like any other fine-motor skill, is best improved
with practice. The more time spent on technical descents the more
your confidence and speed will develop. The difficulty for bicyclists
is that each descent requires a climb. There are hot shots who
practice on their motorcycles before races with strategic descents.
For most of us the best solution is frequent group rides. Group
rides are the best path to developing real bike handling skills,
on descents and elsewhere.

After experience the second most important component of a fast
descent is relaxation. Too much anxiety can impair concentration
and cause you to miss important aspects of the road surface. Pushing
the speed to the point of fear will not help develop descending
skills. Work first on relaxation and smoothness (no sudden movements,
braking or turning) and speed will follow.

Third in importance is technique. Technique, however, is difficult
or impossible to learn from reading about it. For that reason this
article touches on just four of the many technical facets of
descending: apexing, breaking, lean, and passing.

Apexing is the art of straightening out a corner by using the
breadth of the lane or roadway. A fast descender will set up his
or her line well in advance of a corner, entering it from the
outside edge of the road for the widest possible angle. The apex,
or mid-point, is crossed at the opposite or inside edge of the
road, finally exiting again on the outside (always leaving room
for traffic, error and unforeseen hazard). The key is to _gradually_
get into position and _smoothly_ follow the line through the corner.
If you find yourself making _any_ quick, jerky movements take that
as a sign that you need to slow down and devote a little more
attention further up the road.

Use the brakes ONLY up to the beginning of a corner. NEVER APPLY
THE BRAKES THROUGH A CORNER. At that point any traction used for
braking will reduce the traction available for cornering. If you
do have to brake after entering a curve make every effort to
straighten your line before applying the brakes. If the road surface
is good use primarily the front brake. If traction is poor switch
to the rear brake and begin breaking earlier. In auto racing circles
there are two schools of thought on braking technique. One advocates
gradually releasing the brakes upon entering the corner. The other
advises hard braking right up to the beginning of the curve and
abruptly releasing them just before entering the curve. Cyclists
should probably combine these techniques depending on the road
surface, rim trueness, brake pad hardness, headset wear and the
proximity of other riders.

Motorcyclists and bicyclists lean their bikes very differently in
a corner. Motorcyclists keep their bikes as upright as possible
to avoid scraping the pegs or pipes. Bicyclists on the other hand
lean their bikes into the corner and keep the body upright. Both
motorcyclists and bicyclists extend the inside knee down to lower
the center of gravity. To _pedal_ through a corner make like a
motorcyclist and keep the bike upright while the inside pedal is
down.

One of the most difficult aspects of fast descents is passing.
Unfortunately, there are good climbers who are slow descenders. As
a result it is not always possible to begin a descent ahead of
someone who you may want to pass. If you find yourself behind a
slow rider either hang out a safe distance behind or pass quickly
but carefully. Passing on a descent is always difficult and can be
dangerous. By the same token, if you find yourself ahead of someone
who obviously wants to pass, let them by at the earliest safe
moment. It's never appropriate to impede someone's progress on a
training ride whether they are on a bicycle or in a car. Always
make plenty of room for anyone trying to pass no matter what the
speed limit is.

Keep in mind that downhill racing is not what bicycle racing is
all about. There is no need to keep up with the Jones'. This is
what causes many a crash. Compete against yourself on the descents.
Belgians are notoriously slow descenders due to the consistently
rainy conditions there yet some of the best cyclists in the world
train on those rainy roads. Don't get caught pushing it on some
wet or unfamiliar descent. Be prepared for a car or a patch of dirt
or oil in the middle of your path around _every_ blind corner no
matter how many times you've been on a particular road. Take it
easy, relax, exercise your powers of concentration and hammer again
when you can turn the pedals.

If you're interested in exploring this further the best books (and
videos) on bike handling I've read are the "Twist of The Wrist"
series by motorcycle racer Keith Code (http://www.superbikeschool.com).

Roger Marquis )

------------------------------

Subject: 9.15 Descending II
From: Jobst Brandt
Date: Fri, 11 May 2001 16:35:42 PDT

Descending and Fast Cornering

Descending on mountain roads, bicycles can reach speeds that are more
common on motorcycles. Speeds that are otherwise not attainable, or
at least not continuously. Criterium racing also presents this
challenge, but not as intensely. Unlike a motorcycle, the bicycle is
lighter than the rider and power cannot be applied when banked over
when cornering hard. Because narrow bicycle tires inflated hard have
little traction margin, a slip on pavement is usually unrecoverable.

Drifting a Road Bicycle on Pavement

Riders have claimed they can slide a bicycle on dry pavement in curves
to achieve greater cornering speed, as in drifting through a turn. A
drift, in contrast to a slide, means that both wheels slip, which is
even more difficult. This notion may come from observing motorcycles,
that can cause a rear wheel slide by applying power when banked over.
Besides, when questioned about how this is done, the proponent says
that the ability was observed, done by others.

A bicycle can be pedaled only at lean angles far less than the maximum
without grounding a pedal, so hard cornering is always done coasting,
hence, there is no power in hard cornering. Although bicycles with
high ground clearance have been built, they showed only that pedaling
imbalance has such a disturbing influence on traction, that pedaling
at a greater lean angle than that of a standard road racing bicycles
has no benefit. That is why road bicycles are built the way they are,
no higher than is useful.

That bicycle tires have no margin for recovering a slip at maximum
lean angle, has been tested in lean-slip tests on roads and testing
machines. For smooth tires on pavement, slipout occurs at slightly
less than 45 degrees from the road surface and is both precipitous and
unrecoverable. Although knobby tires have a less sudden slipout and
can be drifted around curves, they begin to side-slip at a more
upright angle as their tread fingers walk rather than slip. For this
reason, knobby tires cannot achieve lean angles of smooth tires and
offer no cornering advantage on pavement.

How to Corner

Cornering requires estimating the required lean angle before reaching
the apex of the turn where the angle with the road surface is the
critical parameter rather the angle with the vertical, as is evident
from banked curves. Lean angle is limited by the available traction
that must be assessed from velocity and appearance of the surface.
For good pavement, this angle is about 45 degrees, in the absence of
oil, water, or smooth and slick spots. Therefore, a curve banked
inward 10 degrees, allows a lean of up to at least 55 degrees from the
vertical, while a crowned road with no banking, where the surface
falls off about 10 degrees, would allow only up to 35 degrees.

Banked curves have a greater effect than just adding to the maximum
lean angle, because with a steeper banking, more of the centripetal
cornering force goes into increasing traction directly into the
banking up to the point of a vertical wall where only the maximum
G-forces limit what speed a bicyclists can attain. In contrast, an
off banked curve makes cornering progressively more difficult until
the bicycle will slip even at zero speed. This effect is more
naturally apparent to riders who exceeded these limits early in life
and have added the experience to expected natural phenomena.

The skill of visualizing effects of speed, traction, braking, and
curvature are complex, but is something humans and other creatures do
regularly in self propulsion. The difficulty arises in adapting this
to higher speeds. When running, we anticipate how fast and sharply to
turn on a sidewalk, dirt track, or lawn, to avoid sliding. The method
is the same on a bicycle although the consequences of error are more
severe.

Cornering requires reflexes to dynamics that are easily developed in
youth, while people who have not exercised this in a long time find
they can no longer summon these skills. A single fall strongly
reinforces doubt, so cautious practice is advisable if returning to
bicycling after a long time.

Countersteer

Countersteer is a popular subject for people who belatedly discover or
rediscover how to balance. What is not apparent, is that two wheeled
vehicles can be controlled ONLY by countersteer, there is no other
way. Unlike a car, a bicycle cannot be diverted from a straight path
by steering the wheel to one side. The bicycle must first be leaned
in that direction by steering it ever so slightly the other way. This
is the means by which a broomstick is balanced on the palm of the hand
or a bicycle on the road. The point of support is moved beneath the
mass, in line with the combined forces of gravity and cornering, and
it requires steering, counter and otherwise. It is so obvious that
runners never mention it, although football, basketball, and ice
hockey players conspicuously do it.

Braking

Once the basics of getting around a corner are developed, doing it
fast involves careful use of the brakes. Besides knowing how steeply
to lean in curves, understanding braking makes the difference between
the average and the fast rider. When approaching a curve with good
traction, the front brake can be used almost exclusively, because it
is capable of slowing the bicycle so rapidly that nearly all weight
transfers to the front wheel, at which point the rear brake is nearly
useless. Once in the curve, more and more traction is used to resist
lateral slip as the lean angle increases, but that does not mean the
brakes cannot be used. When banked over, braking should be done with
both brakes, because now neither wheel has much traction to spare and
with lighter braking, weight transfers diminishes. A feel for how
hard the front brake must be applied for rear wheel lift-off, can be
developed at low speed.

Braking in Corners

Why brake in the turn? If all braking is done before the turn, speed
will be slower than necessary before the apex. Anticipating maximum
speed for the apex is difficult, and because the path is not a
circular arc, speed must be trimmed all the way to that point. Fear
of braking in curves usually comes from an incident of injudicious
braking at a point where braking should have been done with a gentle
touch to match the conditions.

Substantial weight transfer from the rear to the front wheel will
occur with strong use of the front brake on good traction just before
entering the curve. When traction is poor or the lean angle is great,
deceleration cannot be large and therefore, weight transfer will be
small, so light braking with both wheels is appropriate. If traction
is miserable, only the rear brake should be used, because although a
rear skid is recoverable, a front skid is generally not. An exception
to this is in deep snow, where the front wheel can slide and function
as a sled runner while being steered.

Braking at maximum lean

For braking in a curve, take the example of a rider cornering with
good traction, leaning at 45 degrees, the equivalent of 1G centrifugal
acceleration. Braking with 1/10g increases the traction demand by one
half percent. The sum of cornering and braking vectors is the square
root of the sum of their squares, SQRT(1^2+0.1^2)=1.005 or an increase
of 0.005. In other words, there is room to brake substantially during
maximum cornering. Because the lean angle changes as the square of
the speed, braking can rapidly reduce the angle and allow even more
braking. For this reason skilled racers nearly always apply both
brakes into the apex of turns.

Suspension

Beyond leaning and braking, suspension helps substantially in
descending. For bicycles without built-in suspension, this is
furnished by the legs. Standing up is not necessary on roads with
fine ripples, just taking the weight off the pelvic bones is adequate.
For rougher roads, enough clearance must be used so the saddle carries
no weight. The reason for this is twofold. Vision will become
blurred if the saddle is not unloaded, and traction will be
compromised if the tires are not bearing with uniform force on the
road while rolling over bumps. Ideally the tires should bear on the
road at constant load. Besides, if the road has whoop-de-doos, the
seated rider will get launched from the saddle and possibly crash.

Lean the Bicycle, the Rider, or Both

Some riders believe that sticking the knee out or leaning the body
away from the bicycle, improves cornering. Sticking out a knee is the
same thing that riders without cleats do when they stick out a foot in
dirt track motorcycle fashion. On paved roads this is a useless but
reassuring gesture that, on uneven roads, even degrades control. Any
body weight that is not centered over the bicycle (leaning the bike or
sticking out a knee) puts a side load on the bicycle, and side loads
cause steering motions over uneven road. Getting weight off the
saddle is also made more difficult by such maneuvers.

To verify this, coast down a straight but rough road, weight on one
pedal with the bike slanted, and note how the bike follows an erratic
line. In contrast, if you ride centered on the bike you can ride
no-hands perfectly straight over the same road. While leaning off the
bike, trail of the front wheel causes steering on rough roads.

Outside Pedal Down

It is often said that putting the outside pedal down in a curve
improves cornering. Although most experienced riders do this, it is
not because it has anything to do with traction. The reason is that
it enables the rider to unload the saddle while standing with little
effort on a locked knee, cushioning his weight on his ankle. This can
only be done on the outside pedal because the inside pedal would hit
the road. However, standing on one extended leg does not work on
rougher roads, because the ankle cannot absorb large road bumps nor
raise the rider high enough from the saddle to avoid getting bounced.
Rough roads require rising high enough from the saddle to avoid hard
contact while the legs supply shock absorbing knee action, with pedals
and cranks horizontal.

Body Contortions

Most of the "body English" riders display is gratuitous gesturing,
much like the motorcyclists who stick their butt out in curves while
their bikes never get down to 45 degrees (the angle below which hiking
out becomes necessary to keep hardware from dragging on the road). In
fact, in a series of tight ess bends, there's no time to do any of
this. It's done by supporting weight on the (horizontally positioned)
pedals, and unless the road is rough, with a light load on the saddle.
On rough roads, the cheeks of the saddle, (the ones that went away
with the Flite like saddles) are used to hold the bicycle stably
between the legs while not sitting.

The path through a curve is not symmetrical for a bicycle, because it
can slow down much faster than it can regain speed. Thus the
trajectory is naturally asymmetric. Brakes are generally used to the
apex (that is usually not the middle) of the curve, where pedaling at
that lean angle is not possible, nor does pedaling accelerate as fast
as braking decelerates.

Hairpin Turns

Although the railroad term switchback arises from early mountain
railroading where at the end of a traverse, a switch is turned to back
up the next traverse, after which another switch is turned to head up
the next, on roads these are hairpin turns. In such turns trajectory
asymmetry is most conspicuous, because braking can be hard enough to
raise the rear wheel when entering but one cannot exit with such
acceleration. For this reason, riders often find themselves with
extra road on the exit of such turns, having slowed down too much.

Vision

Where to direct vision is critical for fast cornering. Central vision
should be focused on the pavement where the tire will track, while
allowing peripheral vision, with its low resolution and good
sensitivity to motion, to detect obstacles and possible oncoming
traffic. Peripheral vision monitors surroundings anyway, so the
presence of a car in that "backdrop" does not require additional
consideration other than its path.

If central vision is directed at the place where an oncoming vehicle
might appear, its appearance presents a new problem of confrontation,
stopping image processing of the road surface for substantial time.
Because the color or model of car is irrelevant, this job can be left
to peripheral vision in high speed primitive processing, while
concentrating on pavement surface and composition.

When following another bicycle or a car downhill, the same technique
is even more important, because by focusing on the leading vehicle,
pavement and road alignment information is being obscured giving a
tendency to mentally become a passenger of that vehicle. Always look
ahead of the vehicle, observing it only peripherally.

Riders often prefer to keep their head upright in curves, although
leaning the head with the bicycle and body is more natural to the
motion. Pilots who roll their aircraft do not attempt to keep their
head level during the maneuver, or in curves, for that matter.

The Line

Picking the broadest curve through a corner may be obvious by the time
the preceding skills are mastered, but that may not be the best line,
either for safety or because the road surface is poor. Sometimes
hitting a bump or a "Bott's dot" is better than altering the line,
especially at high speed. Tires should be large enough to absorb the
entire height of a lane marker without pinching the tube. This means
that a minimum of a 25mm actual cross section tire is advisable. At
times, the crown of the road is sufficient to make broadening the
curve, by taking the curve wide, counterproductive because the crown
on the far side gives a restricted lean angle.

Mental Speed

Mental speed is demanded by all of these. However, being quick does
not guarantee success, because judgment is even more important. To
not be daring but rather to ride with a margin that leaves a feeling
of comfort rather than high risk, is more important. Just the same,
do not be blinded by the age old presumption that everyone who rides
faster than I is crazy. "He descends like a madman!" is one of the
most common descriptions of fast descenders. The comment generally
means that the speaker is slower.

Braking Heat on Steep Descents

Although tandems with their higher weight to wind drag ratio have this
problem more often, steep mountain roads, especially ones with poor or
no pavement require so much braking that single bicycles blow off
tires from overheating. For tubulars the problem is not so much over
pressure than rim glue melting as all pressure sensitive glues do with
heating. As glue softens, tires slip on the hot rim and pile up on
the valve stem. This is the usual indicator that tubular tire wheels
are too hot. The next is that the tire arches off the rim in the area
just before the stem.

This is a serious problem both for tubulars and clinchers because most
clincher tires, given enough time on a hot rim will blow off if
inflated to recommended pressure. Pressure that gives good rolling
performance (hard) while tubulars roll off from lack of adhesion to
the rim. The faster the travel, the more descending power goes into
wind drag and the better the rims are cooled. Going slowly does not
help, unless speed is reduced below walking pace.

On steep descents, where rims stay too hot to touch for more than a
minute, reducing tire inflation pressure is a sure remedy. However,
tires should be re-inflated once the rims cool to normal. The
blow-off pressure is the same for small and large tires on the same
rim, it being dependent only on the opening of the rim width. Also,
tires with a smaller air volume become hot faster than larger ones.

There is no way of descending continuously and steeply without
reducing inflation pressure, unless there is an insulator between the
tube and rim of a clincher. Insulating rim strips are no longer
offered because they were an artifact of dirt roads that often
required riders to descend so slowly that all potential energy went
into the brakes and almost none into wind drag. These rim strips were
cloth tubes filled with kapok, their insulating purpose being unknown
to most people when they were last offered.

------------------------------

Subject: 9.16 Trackstands
From: Rick Smith

How to trackstand on a road bike.

With acknowledgments to my trackstanding mentor,
Neil Bankston.

Practice, Practice, Practice, Practice, ....

1. Wear tennis shoes.
2. Find an open area, like a parking lot that has a slight grade to it.
3. Put bike in a gear around a 42-18.
4. Ride around out of the saddle in a counter-clockwise circle, about
10 feet in diameter.

Label Notation for imaginary points on the circle:
'A' is the lowest elevation point on the circle.
'B' is the 90 degrees counterclockwise from 'A' .
'C' is the highest elevation point on the circle.
'D' is the 90 degrees counterclockwise from 'C' .

C
/ \
D B Aerial View
\ /
A

5. Start slowing down, feeling the different sensation as the bike
transitions between going uphill (B) and downhill (D).
6. Start trying to go real slowly through the A - B region of the circle.
This is the region you will use for trackstanding. Ride the rest of
the circle as you were in step 5.

The trackstanding position (aerial view again):

---| /
------| |----/
|--- /


The pedal are in a 3 o'clock - 9 o'clock arrangement (in other
words, parallel to the ground). Your left foot is forward, your
wheel is pointed left. You are standing and shifting you weight
to keep balance. The key to it all is this:

If you start to fall left, push on the left pedal to move the
bike forward a little and bring you back into balance.

If you start to fall right, let up on the pedal and let the
bike roll back a little and bring you back into balance.

7. Each time you roll through the A - B region, try to stop when
the left pedal is horizontal and forward. If you start to
lose your balance, just continue around the circle and try it
again.

8. Play with it. Try doing it in various regions in the circle,
with various foot position, and various amounts of turn in your
steering. Try it on different amounts of slope in the
pavement. Try different gears. What you are shooting for is
the feel that's involved, and it comes with practice.

The why's of trackstanding:

Why is road bike specified in the title?
A true trackstand on a track bike is done differently. A track
bike can be pedaled backwards, and doesn't need a hill to
accomplish the rollback affect. Track racing trackstands
are done opposite of what is described. They take place on the
C - D region of the circle, with gravity used for the roll
forward, and back pedaling used for the rollback. This is so
that a racer gets the assist from gravity to get going again
when the competition makes a move.

Why a gear around 42-18?
This is a reasonable middle between too small, where you would
reach the bottom of the stroke on the roll forward, and too big,
where you couldn't generate the roll forward force needed.

Why is the circle counter-clockwise?
Because I assume you are living in an area where travel is done
on the right side of the road. When doing trackstands on the road,
most likely it will be at traffic lights. Roads are crowned - higher
in the middle, lower on the shoulders - and you use this crown as
the uphill portion of the circle (region A-B). If you are in a
country where travel is done on the left side of the road,
please interpret the above aerial views as subterranial.

Why is this done out of the saddle?
It's easier!! It can be done in while seated, but you lose the
freedom to do weight adjustments with your hips.

Why is the left crank forward?
If your right crank was forward, you might bump the front wheel
with your toe. Remember the steering is turned so that the back
of the front wheel is on the right side of the bike. Some bikes
have overlap of the region where the wheel can go and your foot
is. Even if your current bike doesn't have overlap, it's better
to learn the technique as described in case you are demonstrating
your new skill on a bike that does have overlap.

Why the A - B region?
It's the easiest. If you wait till the bike is around 'B', then
you have to keep more force on the pedal to hold it still. If
you are around the 'A' point, there may not be enough slope to
allow the bike to roll back.

Questions:

What do I do if I want to stop on a downhill?
While there are techniques that can be employed to keep you in
the pedals, for safety sake I would suggest getting out of the
pedals and putting your foot down.

Other exercises that help:

Getting good balance. Work through this progression:
1. Stand on your right foot. Hold this until it feels stable.
2. Close your eyes. Hold this until it feels stable.
3. Go up on your toes. Hold this until it feels stable.
4. If you get to here, never mind, your balance is already wonderful,
else repeat with other foot.

------------------------------

Subject: 9.17 Front Brake Usage
From: John Forester

I have dealt for many years with the problem of explaining front
brake use, both to students and to courtrooms, and I have reached
some conclusions, both about the facts and about the superstitions.

The question was also asked about British law and front brakes.
I'll answer that first because it is easier. British law requires
brakes on both wheels, but it accepts that a fixed gear provides the
required braking action on the rear wheel. I think that the
requirement was based on reliability, not on deceleration. That is,
if the front brake fails, the fixed-gear cyclist can still come to a
stop.

In my house (in California) we have three track-racing bikes
converted to road use by adding brakes. Two have only front brakes
while the third has two brakes. We have had no trouble at all, and we
ride them over mild hills. The front-brake-only system won't meet the
normal U.S. state traffic law requirement of being able to skid one
wheel, because that was written for coaster-braked bikes, but it
actually provides twice the deceleration of a rear-wheel-braked bike
and nobody, so far as I know, has ever been prosecuted for using such
a setup.

The superstitions about front brake use are numerous. The most
prevalent appears to be that using the front brake without using the
rear brake, or failing to start using the rear brake before using the
front brake, will flip the cyclist. The other side of that
superstition is that using the rear brake will prevent flipping the
bicycle, regardless of how hard the front brake is applied.

The truth is that regardless of how hard the rear brake is
applied, or whether it is applied at all, the sole determinant (aside
from matters such as bicycle geometry, weight and weight distribution
of cyclist and load, that can't practically be changed while moving)
of whether the bicycle will be flipped is the strength of application
of the front brake. As the deceleration to produce flip is
approached, the weight on the rear wheel decreases to zero, so that
the rear wheel cannot produce any deceleration; with no application
of the rear brake it rolls freely, with any application at all it
skids at a force approaching zero. With typical bicycle geometry, a
brake application to attempt to produce a deceleration greater than
0.67 g will flip the bicycle. (Those who advocate the cyclist moving
his butt off and behind the saddle to change the weight distribution
achieve a very small increase in this.)

A typical story is that of a doctor who, now living in the higher-
priced hilly suburbs, purchased a new bicycle after having cycled to
med school on the flats for years. His first ride was from the bike
shop over some minor hills and then up the 15% grade to his house.
His second ride was down that 15% grade. Unfortunately, the rear
brake was adjusted so that it produced, with the lever to the
handlebar, a 0.15 g deceleration. The braking system would meet the
federal requirements of 0.5 g deceleration with less than 40 pounds
grip on the levers, because the front brake has to do the majority of
the work and at 0.5 g there is insufficient weight on the rear wheel
to allow much more rear brake force than would produce 0.1 g
deceleration. (The U.S. regulation allows bicycles with no gear
higher than 60 inches to have only a rear-wheel brake that provides
only 0.27 g deceleration.) I don't say that the rear brake adjustment
of the bicycle in the accident was correct, because if the front
brake fails then the rear brake alone should be able to skid the rear
wheel, which occurs at about 0.3 g deceleration. The doctor starts
down the hill, coasting to develop speed and then discovering that he
can't slow down to a stop using the rear brake alone. That is because
the maximum deceleration produced by the rear brake equalled, almost
exactly, the slope of the hill. He rolls down at constant speed with
the rear brake lever to the handlebar and the front brake not in use
at all. He is afraid to apply the front brake because he fears that
this will flip him, but he is coming closer and closer to a curve,
after which is a stop sign. At the curve he panics and applies the
front brake hard, generating a force greater than 0.67 g deceleration
and therefore flipping himself. Had he applied the front brake with
only a force to produce 0.1 g deceleration, even 100 feet before the
curve, he would have been safe, but in his panic he caused precisely
the type of accident that he feared. He thought that he had a good
case, sued everybody, and lost. This is the type of superstition that
interferes with the cycling of many people.

My standard instruction for people who fear using the front brake
is the same instruction for teaching any person to brake properly.
Tell them to apply both brakes simultaneously, but with the front
brake 3 times harder than the rear brake. Start by accelerating to
road speed and stopping with a gentle application. Then do it again
with a harder application, but keeping the same 3 to 1 ratio. Then
again, harder still, until they feel the rear wheel start to skid.
When the rear wheel skids with 1/4 of the total braking force applied
to it, that shows that the weight distribution has now progressed as
far to the front wheel as the average cyclist should go. By repeated
practice they learn how hard this is, and attain confidence in their
ability to stop as rapidly as is reasonable without any significant
risk.

------------------------------

Subject: 9.18 Slope Wind, the Invisible Enemy
From: Jobst Brandt

Wind as well as relative wind caused by moving through still air
demands most of a bicyclists effort on level ground. Most riders
recognize when they are subjected to wind because it comes in gusts
and these gusts can be distinguished from the more uniform wind caused
by moving through still air. That's the catch. At the break of dawn
there is often no wind as such but cool air near the ground, being
colder and more dense than higher air slides downslope as a laminar
layer that has no turbulent gusts.

Wind in mountain valleys generally blows uphill during the heat of the
day and therefore pilots of light aircraft are warned to take off
uphill against the morning slope wind. Slope wind, although detectable,
is not readily noticed when standing or walking because it has
negligible effect and does not come in apparent gusts. The bicyclist,
in contrast, is hindered by it but cannot detect it because there is
always wind while riding.

Slope wind, as such, can be up to 10 mph before it starts to take on
the characteristics that we expect of wind. It is doubly deceptive
when it comes from behind because it gives an inflated speed that can
be mistakenly attributed to great fitness that suddenly vanishes when
changing course. If you live near aspen or poplars that tend to fan
their leaves in any breeze, you will not be fooled.

------------------------------

Subject: 9.19 Reflective Tape
From: Jobst Brandt

Reflective tape is available in most better bike shops in various
forms, most of which is pre-cut to some preferred shape and designed
for application to some specific part of the bike or apparel. The most
effective use of such tape is on moving parts such as pedals, heel of
the shoe or on a place that is generally overlooked, the inside of the
rim.

First, it is appropriate to note that car headlights generally produce
white light and a white or, in fact, colorless reflector returns more
of this light to its source than ones with color filters or selective
reflection. Red, for instance, is not nearly as effective as white.

Placing reflective tape on the inside of the rims between the spokes
is a highly effective location for night riding because it is visible
equally to the front and rear while attracting attention through its
motion. It is most effective when applied to less than half the rim
in a solid block. Five inter-spoke sections does a good job. One can
argue that it isn't visible from the side (if the rim is not an aero
cross section) but the major hazard is from the front and rear.

Be seen on a bike! It's good for your health.

------------------------------

Subject: 9.20 Nutrition
From: Bruce Hildenbrand

Oh well, I have been promising to do this for a while and given the present
discussions on nutrition, it is about the right time. This article was
written in 1980 for Bicycling Magazine. It has been reprinted in over 30
publications, been the basis for a chapter in a book and cited numerous
other times. I guess somebody besides me thinks its OK. If you disagree
with any points, that's fine, I just don't want to see people take exception
based on their own personal experiences because everyone is different and
psychological factors play a big role(much bigger than you would think)
on how one perceives his/her own nutritional requirements. Remember that
good nutrition is a LONG TERM process that is not really affected by short
term events(drinking poison would be an exception). If it works for you
then do it!!! Don't preach!!!!



BASIC NUTRITION PRIMER

Nutrition in athletics is a very controversial topic. However, for
an athlete to have confidence that his/her diet is beneficial he/she
must understand the role each food component plays in the body's
overall makeup. Conversely, it is important to identify and understand
the nutritional demands on the physiological processes of the body
that occur as a result of racing and training so that these needs
can be satisfied in the athlete's diet.

For the above reasons, a basic nutrition primer should help the athlete
determine the right ingredients of his/her diet which fit training and
racing schedules and existing eating habits. The body requires three
basic components from foods: 1) water; 2) energy; and 3)nutrients.

WATER

Water is essential for life and without a doubt the most important
component in our diet. Proper hydrations not only allows the body to
maintain structural and biochemical integrity, but it also prevents
overheating, through sensible heat loss(perspiration). Many cyclists have
experienced the affects of acute fluid deficiency on a hot day, better
known as heat exhaustion. Dehydration can be a long term problem,
especially at altitude, but this does not seem to be a widespread
problem among cyclists and is only mentioned here as a reminder(but
an important one).

ENERGY

Energy is required for metabolic processes, growth and to support
physical activity. The Food and Nutrition Board of the National
Academy of Sciences has procrastinated in establishing a Recommended
Daily Allowance(RDA) for energy the reasoning being that such a daily
requirement could lead to overeating. A moderately active 70kg(155lb)
man burns about 2700 kcal/day and a moderately active 58kg(128lb) woman
burns about 2500 kcal/day.

It is estimated that cyclists burn 8-10 kcal/min or about 500-600
kcal/hr while riding(this is obviously dependent on the level of
exertion). Thus a three hour training ride can add up to 1800
kcals(the public knows these as calories) to the daily energy demand
of the cyclist. Nutritional studies indicate that there is no
significant increase in the vitamin requirement of the athlete as a
result of this energy expenditure.

In order to meet this extra demand, the cyclist must increase his/her
intake of food. This may come before, during or after a ride but most
likely it will be a combination of all of the above. If for some
reason extra nutrients are required because of this extra energy
demand, they will most likely be replenished through the increased
food intake. Carbohydrates and fats are the body's energy sources and
will be discussed shortly.

NUTRIENTS

This is a broad term and refers to vitamins, minerals, proteins, carbohydrates,
fats, fiber and a host of other substances. The body is a very complex product
of evolution. It can manufacture many of the resources it needs to survive.
However, vitamins, minerals and essential amino acids(the building blocks of
proteins) and fatty acids cannot be manufactured, hence they must be supplied
in our food to support proper health.

Vitamins and Minerals

No explanation needed here except that there are established RDA's for most
vitamins and minerals and that a well balanced diet, especially when
supplemented by a daily multivitamin and mineral tablet should meet all
the requirements of the cyclist.

Proper electrolyte replacement(sodium and potassium salts) should be
emphasized, especially during and after long, hot rides. Commercially
available preparations such as Exceed, Body Fuel and Isostar help
replenish electrolytes lost while riding.

Proteins

Food proteins are necessary for the synthesis of the body's skeletal(muscle,
skin, etc.) and biochemical(enzymes, hormones, etc.)proteins. Contrary
to popular belief, proteins are not a good source of energy in fact they
produce many toxic substances when they are converted to the simple sugars
needed for the body's energy demand.

Americans traditionally eat enough proteins to satisfy their body's
requirement. All indications are that increased levels of exercise do
not cause a significant increase in the body's daily protein
requirement which has been estimated to be 0.8gm protein/kg body
weight.

Carbohydrates

Carbohydrates are divided into two groups, simple and complex, and serve
as one of the body's two main sources of energy.

Simple carbohydrates are better known as sugars, examples being fructose,
glucose(also called dextrose), sucrose(table sugar) and lactose(milk sugar).

The complex carbohydrates include starches and pectins which are multi-linked
chains of glucose. Breads and pastas are rich sources of complex
carbohydrates.

The brain requires glucose for proper functioning which necessitates a
carbohydrate source. The simple sugars are quite easily broken down to
help satisfy energy and brain demands and for this reason they are an ideal
food during racing and training. The complex sugars require a substantially
longer time for breakdown into their glucose sub units and are more suited
before and after riding to help meet the body's energy requirements.

Fats

Fats represent the body's other major energy source. Fats are twice as
dense in calories as carbohydrates(9 kcal/gm vs 4 kcal/gm) but they are
more slowly retrieved from their storage units(triglycerides) than
carbohydrates(glycogen). Recent studies indicate that caffeine may help
speed up the retrieval of fats which would be of benefit on long rides.

Fats are either saturated or unsaturated and most nutritional experts
agree that unsaturated, plant-based varieties are healthier. Animal
fats are saturated(and may contain cholesterol), while plant based fats
such as corn and soybean oils are unsaturated. Unsaturated fats are
necessary to supply essential fatty acids and should be included in the
diet to represent about 25% of the total caloric intake. Most of this
amount we don't really realize we ingest, so it is not necessary to heap
on the margarine as a balanced diet provides adequate amounts.

WHAT THE BODY NEEDS

Now that we have somewhat of an understanding of the role each food
component plays in the body's processes let's relate the nutritional
demands that occur during cycling in an attempt to develop
an adequate diet. Basically our bodies need to function in three
separate areas which require somewhat different nutritional considerations.
These areas a 1) building; 2) recovery; and 3) performance.

Building

Building refers to increasing the body's ability to perform physiological
processes, one example being the gearing up of enzyme systems necessary
for protein synthesis, which results in an increase in muscle mass, oxygen
transport, etc. These systems require amino acids, the building blocks of
proteins. Hence, it is important to eat a diet that contains quality proteins
(expressed as a balance of the essential amino acid sub units present)fish,
red meat, milk and eggs being excellent sources.

As always, the RDA's for vitamins and minerals must also be met but, as with
the protein requirement, they are satisfied in a well balanced diet.

Recovery

This phase may overlap the building process and the nutritional requirements
are complimentary. Training and racing depletes the body of its energy
reserves as well as loss of electrolytes through sweat. Replacing the
energy reserves is accomplished through an increased intake of complex
carbohydrates(60-70% of total calories) and to a lesser extent fat(25%).
Replenishing lost electrolytes is easily accomplished through the use
of the commercial preparations already mentioned.

Performance

Because the performance phase(which includes both training rides and
racing)spans at most 5-7 hours whereas the building and recovery phases
are ongoing processes, its requirements are totally different from the
other two. Good nutrition is a long term proposition meaning the effects
of a vitamin or mineral deficiency take weeks to manifest themselves.
This is evidenced by the fact that it took many months for scurvy to
show in sailors on a vitamin C deficient diet. What this means is that
during the performance phase, the primary concern is energy replacement
(fighting off the dreaded "bonk") while the vitamin and mineral demands
can be overlooked.

Simple sugars such a sucrose, glucose and fructose are the quickest
sources of energy and in moderate quantities of about 100gm/hr(too much
can delay fluid absorption in the stomach) are helpful in providing fuel
for the body and the brain. Proteins and fats are not recommended because
of their slow and energy intensive digestion mechanism.

Short, one day rides or races of up to one hour in length usually require
no special nutritional considerations provided the body's short term energy
stores (glycogen) are not depleted which may be the case during multi-day
events.

Because psychological as well as physiological factors determine performance
most cyclists tend to eat and drink whatever makes them feel "good" during a
ride. This is all right as long as energy considerations are being met and
the stomach is not overloaded trying to digest any fatty or protein containing
foods. If the vitamin and mineral requirements are being satisfied during the
building and recovery phases no additional intake during the performance phase
is necessary.


IMPLICATIONS

Basically, what all this means is that good nutrition for the cyclist is
not hard to come by once we understand our body's nutrient and energy
requirements. If a balanced diet meets the RDA's for protein, vitamins
and minerals as well as carbohydrate and fat intake for energy then everything
should be OK nutritionally. It should be remembered that the problems
associated with nutrient deficiencies take a long time to occur. Because
of this it is not necessary to eat "right" at every meal which explains
why weekend racing junkets can be quite successful on a diet of tortilla
chips and soft drinks. However, bear in mind that over time, the body's
nutritional demands must be satisfied. To play it safe many cyclists
take a daily multivitamin and mineral supplement tablet which has no adverse
affects and something I personally recommend. Mega vitamin doses(levels
five times or more of the RDA) have not been proven to be beneficial and may
cause some toxicity problems.

GREY NUTRITION

"Good" nutrition is not black and white. As we have seen, the body's
requirements are different depending on the phase it is in. While the
building and recovery phases occur somewhat simultaneously the performance
phase stands by itself. For this reason, some foods are beneficial during
one phase but not during another. A good example is the much maligned
twinkie. In the performance phase it is a very quick source of energy
and quite helpful. However, during the building phase it is not necessary
and could be converted to unwanted fat stores. To complicate matters, the
twinkie may help replenish energy stores during the recovery phase however,
complex carbohydrates are probably more beneficial. So, "one man's meat
may be another man's poison."

NUTRIENT DENSITY

This term refers to the quantity of nutrients in a food for its accompanying
caloric(energy) value. A twinkie contains much energy but few vitamins and
minerals so has a low nutrient density. Liver, on the other hand, has a
moderate amount of calories but is rich in vitamins and minerals and is
considered a high nutrient density food.

Basically, one must meet his/her nutrient requirements within the
constraints of his/her energy demands. Persons with a low daily
activity level have a low energy demand and in order to maintain their
body weight must eat high nutrient density foods. As already
mentioned, a cyclist has an increased energy demand but no significant
increase in nutrient requirements. Because of this he/she can eat
foods with a lower nutrient density than the average person. This
means that a cyclist can be less choosy about the foods that are eaten
provided he/she realizes his/her specific nutrient and energy
requirements that must be met.

BALANCED DIET

Now, the definition of that nebulous phrase, "a balanced diet". Taking into
consideration all of the above, a diet emphasizing fruits and vegetables
(fresh if possible), whole grain breads, pasta, cereals, milk, eggs, fish and
red meat(if so desired) will satisfy long term nutritional demands.
These foods need to be combined in such a way that during the building and
recovery phase, about 60-70% of the total calories are coming from carbohydrate
sources, 25% from fats and the remainder(about 15%) from proteins.

It is not necessary to get 100% of the RDA for all vitamins and minerals
at every meal. It may be helpful to determine which nutritional
requirements you wish to satisfy at each meal. Personally, I use breakfast
to satisfy part of my energy requirement by eating toast and cereal. During
lunch I meet some of the energy, protein and to a lesser extent vitamin and
mineral requirements with such foods as yogurt, fruit, and peanut butter
and jelly sandwiches. Dinner is a big meal satisfying energy, protein,
vitamin and mineral requirements with salads, vegetables, pasta, meat and
milk. Between meal snacking is useful to help meet the body's energy
requirement.

CONCLUSION

All this jiberish may not seem to be telling you anything you couldn't
figure out for yourself. The point is that "good" nutrition is not
hard to achieve once one understands the reasons behind his/her dietary
habits. Such habits can easily be modified to accommodate the nutritional
demands of cycling without placing any strict demands on one's lifestyle.

------------------------------

Subject: 9.21 Nuclear Free Energy Bar Recipe
From: Phil Etheridge

Nuclear Free Energy Bars
~~~~~~~~~~~~~~~~~~~~~~~~
Comments and suggestions welcome.

They seem to work well for me. I eat bananas as well, in about equal quanities
to the Nuclear Free Energy Bars. I usually have two drink bottles, one with
water to wash down the food, the other with a carbo drink.

You will maybe note that there are no dairy products in my recipe -- that's
because I'm allergic to them. You could easily replace the soy milk powder
with the cow equivalent, but then you'd definitely have to include some
maltodextrin (my soy drink already has some in it). I plan to replace about
half the honey with maltodextrin when I find a local source. If you prefer
cocoa to carob, you can easily substitute.

C = 250 ml cup, T = 15 ml tablespoon

1 C Oat Bran
1/2 C Toasted Sunflower and/or Sesame seeds, ground (I use a food processor)
1/2 C Soy Milk Powder (the stuff I get has 37% maltodextrin, ~20% dextrose*)
1/2 C Raisins
2T Carob Powder

Mix well, then add to

1/2 C Brown Rice, Cooked and Minced (Using a food processor again)
1/2 C Peanut Butter (more or less, depending on consistency)
1/2 C Honey (I use clear, runny stuff, you may need to warm if it's thicker
and/or add a little water)

Stir and knead (I knead in more Oat Bran or Rolled Oats) until thoroughly
mixed. A cake mixer works well for this. The bars can be reasonably soft, as
a night in the fridge helps to bind it all together. Roll or press out about
1cm thick and cut. Makes about 16, the size I like them (approx 1cm x 1.5cm x
6cm).

* Can't remember exact name, dextrose something)

------------------------------

Subject: 9.22 Powerbars Recipe
From: John McClintic

Have you ever watched a hummingbird? Think about it! Hummingbirds
eat constantly to survive. We lumpish earthbound creatures are in
no position to imitate this. Simply, if we overeat we get fat.

There are exceptions: those who exercise very strenuously can
utilize - indeed, actually need - large amounts of carbohydrates.

For example, Marathon runners "load" carbohydrates by stuffing
themselves with pasta before a race. On the flip side Long-distance
cyclists maintain their energy level by "power snacking".

With reward to the cyclist and their need for "power snacking"
I submit the following "power bar" recipe which was originated
by a fellow named Bill Paterson. Bill is from Portland Oregon.

The odd ingredient in the bar, paraffin, is widely used in chocolate
manufacture to improve smoothness and flowability, raise the melting
point, and retard deterioration of texture and flavor. Butter can be
used instead, but a butter-chocolate mixture doesn't cover as thinly
or smoothly.

POWER BARS
----------

1 cup regular rolled oats
1/2 cup sesame seed
1 1/2 cups dried apricots, finely chopped
1 1/2 cups raisins
1 cup shredded unsweetened dry coconut
1 cup blanched almonds, chopped
1/2 cup nonfat dry milk
1/2 cup toasted wheat germ
2 teaspoons butter or margarine
1 cup light corn syrup
3/4 cup sugar
1 1/4 cups chunk-style peanut butter
1 teaspoon orange extract
2 teaspoons grated orange peel
1 package (12 oz.) or 2 cups semisweet chocolate
baking chips
4 ounces paraffin or 3/4 cup (3/4 lb.) butter or
margarine

Spread oats in a 10- by 15-inch baking pan. Bake in a 300 degree
oven until oats are toasted, about 25 minutes. Stir frequently to
prevent scorching.

Meanwhile, place sesame seed in a 10- to 12-inch frying pan over
medium heat. Shake often or stir until seeds are golden, about 7 minutes.

Pour into a large bowl. Add apricots, raisins, coconut, almonds,
dry milk, and wheat germ; mix well. Mix hot oats into dried fruit
mixture.

Butter the hot backing pan; set aside.

In the frying pan, combine corn syrup and sugar; bring to a rolling
boil over medium high heat and quickly stir in the peanut butter,
orange extract, and orange peel.

At once, pour over the oatmeal mixture and mix well. Quickly spread
in buttered pan an press into an even layer. Then cover and chill
until firm, at least 4 hours or until next day.

Cut into bars about 1 1/4 by 2 1/2 inches.

Combine chocolate chips and paraffin in to top of a double boiler.
Place over simmering water until melted; stir often. Turn heat to low.

Using tongs, dip 1 bar at a time into chocolate, hold over pan until
it stops dripping (with paraffin, the coating firms very quickly), then
place on wire racks set above waxed paper.

When firm and cool (bars with butter in the chocolate coating may need
to be chilled), serve bars, or wrap individually in foil. Store in the
refrigerator up to 4 weeks; freeze to store longer. Makes about 4 dozen
bars, about 1 ounce each.

Per piece: 188 cal.; 4.4 g protein; 29 g carbo.; 9.8 g fat;
0.6 mg chol.; 40 mg sodium.

------------------------------

Subject: 9.23 Calories burned by cycling
From: Jeff Patterson

The following table appears in the '92 Schwinn ATB catalog which references
Bicycling, May 1989:
---------
Speed
(mph) 12 14 15 16 17 18 19
Rider
Weight Calories/Hr
110 293 348 404 448 509 586 662
120 315 375 437 484 550 634 718
130 338 402 469 521 592 683 773
140 360 430 502 557 633 731 828
150 383 457 534 593 675 779 883
160 405 485 567 629 717 828 938
170 427 512 599 666 758 876 993
180 450 540 632 702 800 925 1048
190 472 567 664 738 841 973 1104
200 495 595 697 774 883 1021 1159

(flat terrain, no wind, upright position)

------------------------------

Subject: 9.24 Road Rash Cures
From: E Shekita

[Ed note: This is a condensation of a summary of cures for road rash that
Gene posted.]

The July 1990 issue of Bicycle Guide has a decent article on road
rash. Several experienced trainers/doctors are quoted. They generally
recommended:

- cleaning the wound ASAP using an anti-bacterial soap such as Betadine.
Showering is recommended, as running water will help flush out dirt
and grit. If you can't get to a shower right away, at the very least
dab the wound with an anti-bacteria solution and cover the wound with
a non-stick telfa pad coated with bactrin or neosporin to prevent
infection and scabbing. The wound can then be showered clean when you
get home. It often helps to put an ice bag on the wound after it has
been covered to reduce swelling.

- after the wound has been showered clean, cover the wound with either
1) a non-stick telfa pad coated with bactrin or neosporin, or 2) one
of the Second Skin type products that are available. If you go the telfa
pad route, daily dressing changes will be required until a thin layer
of new skin has grown over the wound. If you go the Second Skin route,
follow the directions on the package.

The general consensus was that scabbing should be prevented and that the
Second Skin type products were the most convenient -- less dressing changes
and they hold up in a shower. (Silvadene was not mentioned, probably because
it requires a prescription.)

It was pointed out that if one of the above treatments is followed, then
you don't have to go crazy scrubbing out the last piece of grit or dirt
in the wound, as some people believe. This is because most of the grit
will "float" out of the wound on its own when a moist dressing is used.

There are now products that go by the names Bioclusive, Tegaderm,
DuoDerm, Op-Site, Vigilon, Spenco 2nd Skin, and others, that are like
miracle skin. This stuff can be expensive ($5 for 8 3x4 sheets), but
does not need to be changed. They are made of a 96% water substance
called hydrogel wrapped in thin porous plastic. Two non-porous plastic
sheets cover the hydrogel; One sheet is removed so that the hydrogel
contacts the wound and the other non-porous sheet protects the wound.

These products are a clear, second skin that goes over the cleaned
(ouch!) wound. They breathe, are quite resistant to showering, and
wounds heal in around 1 week. If it means anything, the Olympic
Training Center uses this stuff. You never get a scab with this, so you
can be out riding the same day, if you aren't too sore.

It is important when using this treatment, to thoroughly clean the
wound, and put the bandage on right away. It can be obtained at most
pharmacies. Another possible source is Spenco second skin, which is
sometimes carried by running stores and outdoor/cycling/ stores. If
this doesn't help, you might try a surgical supply or medical supply
place. They aren't as oriented toward retail, but may carry larger sizes
than is commonly available. Also, you might check with a doctor, or
university athletic department people.

------------------------------

Subject: 9.25 Knee problems
From: Roger Marquis

[More up to date copies of Roger's articles can be found at
http://www.roble.net/marquis/]

As the weather becomes more conducive to riding, the racing season
gets going, and average weekly training distances start to climb
a few of us will have some trouble with our knees. Usually knee
problem are caused by one of four things:

1) Riding too hard, too soon. Don't get impatient. It's going
to be a long season and there's plenty of time to get in the
proper progression of efforts. Successful cycling is a matter
of listening to your body. When you see cyclists burning out,
hurting themselves and just not progressing past a certain
point you can be fairly certain that it is because they are
not paying enough attention to what their bodies are saying.

2) Too many miles. The human body is not a machine. It cannot
take all the miles we sometimes feel compelled to ride without
time to grow and adapt. Keep this in mind whenever you feel
like increasing average weekly mileage by more than forty
miles over two or three weeks and you should have no problems.

3) Low, low rpms (also excessive crank length). Save those
big ring climbs and big gear sprints for later in the season.
This is the time of year to develop fast twitch muscle fibers.
That means spin, spin, spin. You don't have to spin all the
time but the effort put into small gear sprints and high rpm
climbing now will pay off later in the season. Mountain bikers
need to be especially careful of low rpms. I generally
recommend that even full time MTB competitors do most of
their training on the road.

4) Improper position on the bike. Unfortunately most bicycle
salespeople in this country have no idea how to properly set
saddle height, the most common error being to set it too low.
This is very conducive to developing knee problems because
of excessive bend at the knee when the pedal is at, and just
past top dead center.

If you've avoided these common mistakes yet are still experiencing
knee problems first make sure your seat and cleats are adjusted
properly then:

1) Check for leg length differences both below and above the
knee. If the difference is between 2 and 8 millimeters you
can correct it by putting spacers under one cleat. If one
leg is shorter by more than a centimeter or so you might
experiment with a shorter crank arm on the short leg side.

2) Use shorter cranks. For some riders this helps keep pedal
speed up and knee stress down. I'm over 6 ft. tall and use
170mm cranks for much of the off season.

3) Try the Fit-Kit R.A.D. cleat alignment device and/or a
rotating type cleat/pedal system.

4) Cut way back on mileage and intensity (This is a last
resort for obvious reasons). Sometimes a prolonged rest is
the only way to regain full functionality and is usually
required only after trying to "train through" pain.

Roger Marquis (www.roble.net/marquis)

------------------------------

Subject: 9.26 Cycling Psychology
From: Roger Marquis

[More up to date copies of Roger's articles can be found at
http://www.roble.net/marquis/]

Motivation, the last frontier. With enough of it any ordinary person
can become a world class athlete. Without it the same person could
end up begging for change downtown. Even a tremendously talented
rider will go nowhere without motivation. How do some riders always
seem to be so motivated? What are the sources of their motivation?
This has been a central theme of sports psychology since its
beginning when Triplett studied the effects of audience and
competition on performance in the late nineteenth century. Though
a great deal has been written on motivation since Triplett it is
still an individual construct. As an athlete you need to identify
what motivates you and cultivate the sources of your motivation.
Here are a few popular methods.

GOALS. One of the best sources of motivation is setting goals. Be
specific and put them down on paper. Define your goals clearly and
make them attainable. Short term goals are more important than long
term goals and should be even more precisely defined. Set short
term goals for things like going on a good ride this afternoon,
doing five sprints, bettering your time on a known course, etc.
Set long term goals such as training at least five days a week,
placing in specific races, upgrading... DO NOT STRESS WINNING when
defining your goals. Instead stress enjoying the ride and doing
your best in every ride and race.

GROUP TRAINING. Training with friends, racing as a team, and all
the other social benefits of our sport are also great for motivation.
This is what clubs should be all about. With or without a club,
group training is vastly more effective than individual training.
The same intensity that can make solo training a challenge comes
naturally in a good group. Ever notice how easy a smooth rotating
paceline seems, until you arrive home to find a surprising soreness
in the quadriceps? Why beat yourself over the head when a few phone
calls (or emails) will generally find plenty of like minded
compatriots. As a general rule try to limit solo training to between
10% and 50% of total miles.

REGULARITY. It's nice to be regular, in more ways than one ;-)
Regularity makes difficult tasks easy. If you make it a point to
ride every day, or at least five times a week (to be competitive),
making the daily ride will become automatic. Riding at the same
time every day can also be helpful but be careful not to become a
slave to the schedule.

LOCATION. The 3 keys to a successful business, "location, location,
and location" are also key to effective cycling. The importance of
conveniently located rides, races, coaches, flexible school and
employment cannot be underemphasized. Good training partners, good
weather, good roads and minimal traffic can also make those long,
hard rides both easier AND more productive.

RACING. The best European pros actually do very little training.
Need I say more? There simply is no better way to improve fitness
and skill. Whether racing to place or to train the savvy cyclist
will do all the racing his or her motivation allows.

AS WELL AS cycling books, magazines and videos, new bike parts,
new clothing, new roads, nice weather, losing weight, seeing friends,
getting out of the city and breathing fresh air, riding hard and
feeling good, and especially the great feeling of accomplishment
and relaxation after every ride that makes life beautiful.

----------------

While high levels of excitation (motivational energy) are generally
better for shorter rides and track races, be careful not to get
over-excited before longer races. Stay relaxed and conserve precious
energy for that crosswind section or sprint where you'll need all
the strength you've got. Learn how psyched you need to be to do
your best and be aware of when you are over or under aroused.

It's not uncommon, especially in early season races, to be so
nervous before the start that fatigue sets in early or even before
the race. Too much stress can make it difficult to ride safely and
should be recognized and controlled immediately. If you find yourself
becoming too stressed before a race try stretching, talking to
friends, finding a quiet place to warm-up, or a crowded place
depending on your inclination. Remember that this stress will
disappear as soon as the race starts. Racing takes too much
concentration to spare any for worrying.

Every athlete needs to be adept in stress management. One technique
used to reduce competitive anxiety is imagery, also known as
visualization. While mental practice has been credited with miraculous
improvements in fine motor skills (archery, tennis) its greatest
value in gross motor sports like cycling lies in stress reduction.

Actually winning a race can also help put an end to excessive
competitive anxiety. But if you have never won (like most cyclists)
nervousness may be keeping you from that rewarding place on the
podium.

----------------

If you find yourself getting overstressed when thinking about
winning, or even riding a race try this; Find a quiet, relaxing
place to sit and think about racing. Second; Picture yourself
driving to the race in a very relaxed and poised state of mind.
Continue visualizing the day progressing into the race and going
well until you detect some tension THEN STOP. Do not let yourself
get excited at all. End the visualization session and try it again
the next day. Continue this DAILY until you can picture yourself
racing and winning without any stress. If this seems like a lot of
work evaluate just how much you want to win a bike race.


Visualization is not meant to replace on the bike training but can
make that training pay off in a big way. Eastern European research
has found that athletes improve most quickly if visual training
comprises fifty to seventy-five percent of the total time spent
training! Like any training imagery will only pay off if you do it
regularly and frequently. My French club coach always used to tell
us: believe it and it will become true.

(C) 1989, Roger Marquis (www.roble.net/marquis)
See also VeloNews, 3-91

------------------------------

Subject: 9.27 Mirrors
From: Jobst Brandt

Mirrors are mandatory on virtually every other type of vehicle on
the road. Competent drivers/riders learn the limitations of the
information available from their mirrors and act accordingly.


I suppose the question is appropriate because no one seems to have
a good explanation for this. In such an event, when there is much
evidence that what would seem obvious is not what is practiced, I
assume there are other things at work. I for one don't wear glasses
to which to attach a mirror and putting it on a helmet seems a
fragile location when the helmet is placed anywhere but on the head.

These are not the real reasons though, because I have found that when
looking in a head mounted mirror, I cannot accurately tell anything
about the following vehicle's position except that it is behind me.
That is because I am looking into a mirror whose angular position
with respect to the road is unknown. The rear view mirror in a car
is fixed with respect to the direction of travel and objects seen in
it are seen with reference to ones own vehicle, be that the rear
window frame or side of the car. I find the image in a head mounted
mirror on a bicycle to be distracting and a source of paranoia if
I watch it enough. It does not tell me whether the upcoming car is,
or is not, going to slice me.

I additionally I find it difficult to focus on objects when my
eyeballs are distorted by turning them as much as 45 degrees to the
side of straight ahead. You can try this by reading these words with
your head turned 45 degrees from the text.

I believe these two effects are the prime reasons for the unpopularity
of such mirrors. They don't provide the function adequately and still
require the rider to look back. I do not doubt that it is possible to
rely on the mirror but it does not disprove my contention that the
information seen is by no means equivalent to motor vehicle rear view
mirrors to which these mirrors have been compared. It is not a valid
comparison.

------------------------------

Subject: 9.28 == Powerbars NO more --- homemade -- YES!!!
From: (Eric Conrad)

I don't know about any of you out there in cyber-mtbike-land, but I was
getting tired of buying Powerbars and other nutrition supplements to enhance
my riding. However, I do understand the benefit of having a quick, nutritious
snack that is full of energy on hand during a ride.

So I asked around and came up with a recipe for Powerbar-like bars that seem
to have a lot of what we need. I'll place the recipe here on the Usenet for
all to copy, distribute ... [but please don't market them, cause I'll only
kick myself for not doing it first ;-) ].

Please make them and enjoy them before you think about flaming me. Trust me,
you'll like them much more than Powerbars, and they're cheaper to make than to
buy their counterpart.

ALSO, PLEASE POST ANY OTHER RECIPES YOU HAVE FOUND THAT HELP BIKING
PERFORMANCE!!!


Eric

BARS OF IRON :-}

1 Cup dark raisins 1 1/2 teaspoon baking powder
1/2 Cup golden raisins 1/2 teaspoon baking soda
1/3 Cup butter or Margarine 1/2 teaspoon salt
1/2 Cup sugar 1/2 teaspoon ground ginger
1 egg 1/2 Cup liquid milk
1 1/4 Cup Whole Wheat Flour 1 Cup quick cooking oats
1/4 Cup toasted wheat germ 1 Cup sliced almonds (optional)
1/2 Cup golden molasses (dark is ok also)
1/2 Cup Nonfat dry milk


Chop raisins (in food processor if possible). Cream butter, sugar, molasses &
egg.

Combine flour, dry milk, wheat germ, baking powder, baking soda, salt and
ginger. Blend into creamed mixture with liquid milk. Stir in oats, raisins,
and half the almonds (if desired).

Pour into greased 13x9x2 inch pan and spread evenly. Sprinkle with remaining
almonds (if desired).

Bake at 350 degrees for approx. 30 minutes. Cool in pan and cut into 1x4 inch
bars.

------------------------------

Subject: 9.29 Lower back pain
From: "David LaPorte (Biochem)"

I'm not a medical expert, but I've had my share of low back pain and I've
learned a few things. When in doubt, go see a medical professional.

Low back pain is one of the most common problems afflicting humans. It's
been estimated that about 80% of these problems arise because of poor
posture. These posture problems occur when we stand but are even more
significant when we sit or ride a bike. We tend to round up our low
backs, stressing the ligaments and tendons which lie along the spine. It is
the irritation and inflammation of these ligaments and tendons which leads
to most low back problems.

It is important to remember that back pain results from the sum total of
ALL the stresses your back experiences. Even if you only experience pain
when you're riding, poor riding posture may not be your only problem.
For example, you may be sitting poorly at a desk all day or lifting boxes
poorly.


**Low Back Pain and Posture**

Since posture is the problem, it is also the solution. Those of us who
suffer from low back pain need to be constantly vigilant. We need to
maintain some arch in our backs as much as possible.

Sitting is a particular problem. Most chairs, coaches, car seats, etc
provide little low back support. You can buy low-back support pads at some
drug stores. Try them before you buy them because they are not all
comfortable. Alternatively, you can fold a towel and put it behind your
low back. The key is to maintain some arch without being uncomfortable.

Position on the bike is also important. Get your bike fit checked at a
shop that you trust. You should also work on maintaining a flat back
when riding. One way to achieve this is to push your belly button toward
the top tube.


***Stretching***

Stretching is an important way to achieve flexibility and improve your
posture. A very useful stretch is to place you hands on you butt and
push your hips forward while standing:

o
\
/

you should feel this in the front of your hips. Tight hip flexors
prevent an upright posture. After a few seconds, arch your back and
slide your hands down the back of your thighs:

o
|)
/

This movement puts the arch in you low back. You can do this stretch
many times a day. It is particularly useful to do it periodically when
you have to sit or ride for an extended period of time.

A more potent stretch that can be done a couple of times a day starts
with you lying on your front. Using your arms, push your shoulders off
the floor. Don't lift with your back. Keep your low back as relaxed as
possible. Let your hips hang down, staying as close to the floor as
possible.

o
__/|

This is a powerful stretch and should be started gradually. Otherwise,
it can do more harm than good. However, done properly, it can be
enormously helpful. Over a period of weeks, you should gradually
increase the height you achieve and the time you hold the position. It
is also less stressful to do this stretch for short periods with a little
rest than for a long period (for example, 3 X 10 sec with 5 sec rest
rather than for 30 sec straight).

Once your back starts to heal, you will probably need to stretch it
deliberately. This is apparently because of the scar tissue that built
up during healing. Keep it gentle, especially at first. You could
easily reinjure your back. Here's a good one: lie on your back with your
legs straight. Pull your knees up, grasp your thighs by your hamstrings
and gently pull your knees to your chest.

Stretching the ham strings can also help relieve low back pain. Tight
ham strings tend to pull the pelvis out of line. This can stress your
low back. The problem with most ham string stretches is that they also
tend to stretch the low back by forcing it to round up. The most
appropriate stretch I know requires the use of a doorway. Lie in the
doorway with your butt near the wall. Gently slide your foot up the
wall until you feel the stretch.

doorway
|
|-
||
||
|___|____O
/

Two ways to make the stretch more gentle are (1) bend the lower leg,
keeping only your foot on the floor or (2) move your butt further away
from the wall. To make the stretch more intense, loop a cord or towel
over your raised foot and gently pull it away from the wall. As with all
stretches, this shouldn't hurt.


***Exercises***

Another key to preventing low back pain is to keep your abdominal muscles
strong. These muscles help support the back. Do abdominal crunchers,
not sit ups. Sit ups emphasize the hip flexors, not the abs, and can be
hard on the back. Crunchers are done by lying on your back with your
knees bent. Press your low back into the floor and curl your head and
shoulders off the floor. Hold for a couple of seconds, then lower back
to the floor. Repeat until you can't get your shoulder blades off the
floor. Abs can be worked every day.

Strengthening the low back muscles can also be helpful. To start, lie on
your front with your arms and legs extended in a straight line with your
body. Raise your right arm and left leg. Put them down and raise your
left arm and right leg. Put them down and continue. As your back
strength improves, try raising both arms and legs at the same time, arching
your back in a "reverse stomach crunch". There are, of course, more
powerful back exercises, but they are also more stressful and shouldn't
be considered until your back is 110%.


***Medication***

Antiinflamitory medication can be helpful. Ibuprofen, naproxin and
aspirin are all available without a prescription. Acetominophen (eg.
Tylanol) is NOT an antiinflamatory. These drugs are most effective if
they are taken early since inflamation is hard to get rid of once it's
become established.

A danger in antiinflamatory drugs is that they are also pain killers.
Pain is your body's way of telling you that your doing damage. If you
block the pain signals, you can easily aggravate your injury without
knowing it.

Muscle relaxants are sometime prescribed for back problems. These should
only be obtained from a physician.


***Ice, Heat and Massage***

Ice is a great way to reduce pain and inflamation. A good way to apply
ice is to freeze water in a paper cup. Peel the cup back to expose the
ice and then use the cup as a handle while gently rubbing the ice over
the effected area. Ice is particularly good for the first couple of
days. Some people find that it's useful to continue ice treatments
beyond that. Others find that the ice treatments make their backs tight
if they continue beyond a couple of days.

Heat, especially moist heat, can be useful. However, it should not be
used for a couple of days after injuring your back or after aggravating a
current injury. Regardless of the timing, if you feel worse during or
shortly after heat treatment, stop doing it.

In the later stages of a back problem, I find that my low back muscles
get tight. Gentle massage seems to help them relax, promoting the
healing process. I suspect that massage could make things worse in some
cases, such as when the injury is fresh.


***Book***

An excellent book on this subject is "Treat Your Own Back" by Robin
McKenzie, Spinal Publications Ltd., P.O. Box 93, Waikanae, New Zealand
ISBN 0-9597746-6-1. They use this book at the Low Back Center of the
University of Minnesota Hospital.

------------------------------

Subject: 9.30 Saddle Sores
From:
(Lee Green MD MPH)

I think I'm developing a couple of saddle sores. I'm curious as to an
effective treatment for them, and effective preventative measures I can


It recurs intermittently here. Lots of comments about keeping clean to
keep the bugs at bay, all to the good.

However, there is more to saddle sores than infection. Skin has several
defenses against bacterial invasion, all of which must fail before
infection occurs.

Abrasion breaks the physical barrier, and preventing it is the reason for
good bike shorts. Lubrication is sometimes helpful too. I recommend not
Vaseline but Desitin. Yup, the diaper rash stuff. Some advocate bag balm
(there seems to be a whole cult of folk medicine around bag balm,
actually) but I'd say best avoid it: it softens skin, which is just what
you don't want.

The point that most posters here seem to miss is probably the most
important though: tissue ischemia. That is, the skin and subcutaneous fat
between your bones and the saddle get compressed. Blood doesn't flow
through them much. Low blood flow is "ischemia", meaning not much oxygen,
nutrients, antibodies, white blood cells, and other good things delivered
to the area.

Ischemic tissue is highly susceptible to infection, heals poorly, and can
break down and form a sore just from ischemia, without any infection at
all. It's similar to the pressure sores that nursing home patients
suffer.

Keep clean, use lubricants if they seem to help, but especially wear good
bike shorts, *make sure your saddle fits properly*, and *get off the
saddle often to allow blood flow through the tissues.*

There is more to saddle sores if you're interested in a lot of technical
detail regarding oxygen tension, shear forces, etc but e-mail me if you
want the gory details.

------------------------------

Subject: 9.31 Group Riding Tips
From: Roger Marquis

[More up to date copies of Roger's articles can be found at
http://www.roble.com/marquis/]

There is no more effective way to become a motivated cyclist than
finding a good regular group ride. Here are some group riding
techniques common around the world.

* Pacelines, Pacelines, Pacelines. Single or double, rotating
quickly or slowly but always smooth and tight. This is the single
overriding feature common to every experienced group ride.

* Accelerate slowly and with an eye to keeping the group together.
Attacks, jumps, short-hard pulls and other race-like riding may be
fine for certain smaller rides but have no place in a group oriented
ride. I'm often surprised that novice riders sometimes think this
kind of aggressive riding is better training than a good rotating
paceline.

* A consistent pace is key. Try establishing a pedaling rhythm
before reaching the front, and maintain it until just after pulling
off. If you're feeling especially strong accelerate and/or take a
longer pull but if you do increase the pace do it gradually. Don't
forget to pedal harder on descents to make up for the extra
aerodynamic resistance.

* Go hard on the hills (and elsewhere) but don't forget to regroup.
This doesn't mean waiting for every last straggler but always make
a reasonable effort to regroup after the harder sections.

* Wheelsitters are always welcome, but please stay at the back.
There's nothing more disruptive than someone who rotates to the
front only to slow down on hitting the wind. If you're feeling
extended, tired, or otherwise not inclined to pull through there's
no problem with sitting at the back, just let the riders who are
rotating know when they've reached the back of the rotating section.

* Don't open gaps! If you find yourself behind a gap close it
_slowly_. A skilled group will remain in a tight paceline through
95% of an average ride including stops, corners, short climbs,
descents, and traffic by closing the inevitable gaps before they
become problems.

* Don't point out every single pothole, oncoming car, or other
obstacle. Each rider has to take responsibility for themselves.
This means that everyone should be paying attention to the traffic
and the road, even at the back. The frontmost riders should point
out unusual hazards of course, and steer the group gradually around
glass, potholes, slower riders and such but don't ever assume that
you can leave it up to the other riders to watch the road ahead.

* The lead riders are most responsible for the group's behavior
and must take this into account at stop signs and lights. Don't
accelerate through a yellow light unless you know the back of the
group can make it too. If the group does get split ride slow until
the rear group has caught back on. If you're at the back please
don't run the intersection just to maintain contact unless it is
clear that traffic is waiting for the entire group to pass.

* Don't accommodate elitist attitudes. Perhaps the best thing about
good group rides, aside from training, is socializing. Team
affiliation, racing experience, helmet use, type of bicycle, etc.
are all matters of individual preference and should be left as
such. As long as the rider is safe and able to keep up they should
be welcome.

* Experienced riders should point out mistakes. This must be done
diplomatically of course but it is important to make people aware
of unsafe riding, hard braking, cutting blind corners, unnecessarily
obstructing traffic, etc.

* It's also helpful to meet at a popular, central location. Cafes,
plazas, and bike shops are all good places to wait and talk before
the ride starts.

* Finally, a a href="http://www.roble.net/marquis/clinic"skills
clinic/a can be an excellent method of helping new riders achieve
the safety and proficiency necessary to participate in a paceline.

Roger Marquis


------------------------------

Subject: 9.32 Riding in echelon
From: Kevin metcalfe
Date: Fri, 13 Sep 1996 16:47:03 -0700 (PDT)

The "fan" you guys are talking about is called an echelon. It is
something that even a lot of good cat 1 and 2 riders can't do properly.
It looks something like this: (Each "|" is a rider.)

Wind from the left Wind from the right
|| ||
|| ||
|| ||
|| ||
|| ||
|| ||
| |
| |
| |

The single file guys at the bottom of the picture are "in the gutter".
Though they may be behind another rider they are getting almost no draft
and their days are numbered unless they can get into the echelon proper.

The riders in the echelon will rotate through from the sheltered side to
the front and then back in the windward side. i.e. With wind from the
left you rotate counter clockwise and you rotate clockwise when the wind
is from the right. If you are riding in a echelon and you want to keep
things smooth and together you will NEVER take a big long pull on the
front. You will always just rotate through. If you take a big pull at
the front, the previously pulling riders will continue to drift back.
Especially since the last guy to pull is still in the wind waiting for
you to swing over and give him a draft! What you'll end up with is a
single file echelon. This is bad because the number of riders that can
fit into an echelon is determined by the width of the road. If you go
single file, then only half as many can fit into the echelon and you've
got a lot of ****ed off riders pushing the wind.

A strong team (like ONCE) can cause a lot of damage in a cross wind. By
putting the whole team on the front and making the echelon just wide
enough for the team, they can drive the pace up front hard enough to
shatter the field. Smart riders will start forming second and third
echelons behind the original. This is the best thing to do.
Unfortunately there are two problems. First, as soon as you get close,
some moron will try and jump across to the first echelon. This is
usually stupid because the reason you are in the second echelon is
because they're no room in the first one. So the offending moron will
often find himself stuck in the gutter unless he can muscle his way into
the echelon. (A lot like trying to knock Abdu off of his leadout man
with 300 meters to go.) The second problem is that most of the stronger
riders are probably already in the first echelon so you're at a
horsepower disadvantage.

Often, early in a race, the field might encounter a strong cross wind and
break into as many as eight or ten echelons. Each echelon will be within
50 to 100 meters of the next one. They will continue like this until the
course turns either into or with the wind and the group will reform.
Just because you aren't physically connected to the front group in this
situation IS NOT NECESSARILY A REASON TO PANIC. If there are only ten
miles to go however, feel free to panic.

There's nothing about an echelon that makes it faster than a regular pace
line. The reason it will break the field up is that only part of the
field will fit in an echelon.

------------------------------

Subject: 9.33 Mirrors II
From: Richard Moorman
Date: Tue, 8 Oct 96 22:42 MDT

Helmet mirrors are very useful for nearsighted people with glasses. I use
my mirror to determine what's going to affect my travels in the next ten or
fifteen seconds. I don't worry about absolute accuracy, I just want the big
picture. If I want that information without a mirror, I have to twist my
body and head around so that I can look at the road behind me through my
glasses. To do this correctly I have to take my left hand off the bars,
disorient myself, and risk wobbling around a lot. It's dangerous. With the
mirror, it's just a glance up and to the left for a second or two. Mirrors
aren't for everyone, but for some of us they're wonderful. I use a mirror
despite the bad design that makes the plastic ones ridiculously breakable.
I hope that someone develops a flexible, springy mirror mount. It seems an
enormously obvious idea.

------------------------------

Subject: 9.34 Thorns aka Puncture Vine
From: Jobst Brandt
Date: Thu, 21 Sep 2000 16:54:00 PDT

Not all riders suffer from thorns which seems mainly to be a function
of avoidance rather than luck or protective means in the tires.
Rather than searching for tires or sealants that will survive thorns,
recognizing the plant is a more effective step toward avoiding flats.
The plant is not mobile and does not propel its seed pods away from
its tendrils. However, some riders think nothing of pulling thorns
from their tires and throwing them on the road as they patch their
tires. This practice seems to be part of not understanding avoidance.
In my experience, riders who suffer most from thorns, have no idea of
the plants appearance or its habitat. Most, think the yellow star
thistle is puncture vine which it is not and it cannot penetrating a
tire.

Puncture vine, tribulus terrestris, grows mainly on barren soil,
typically on roadsides that have been sprayed with herbicides to
prevent grass fires from discarded but burning cigarettes. The plant
germinates after the heat of summer has begun and grows from a central
tap root that reaches as deep as three meters. It has flesh colored
tendrils that radiate 30 to 50 cm with 1 x 3 cm dark green compound
filigree leaves that follow the sun. Its 1 cm diameter blossoms with
five yellow petals produce spherical seed clusters that separate into
five hardwood seed pods when ripe. Each pod or segment has two 6 mm
long thorns extending from the top of the arches so that gravity will
make one of the two thorns point upward. The plant produces seeds
throughout its annual growth.

Some examples:

http://www.cwma.org/puncturevine.html

http://www.or.blm.gov:80/Prineville/weed/puncture.htm

http://tinyurl.com/d0xo

------------------------------

Subject: 9.35 Gyroscopic Forces
From: Jobst Brandt
Date: Fri, 13 Feb 2004 12:07:59 -0800

What keeps the bicycle upright?

The question is often asked and, as often as not, is an introduction
to expound on the gyroscopic forces of the rotating wheels that make
bicycling possible. This claim is as accurate as the one that
authoritatively explains that spokes support the bicycle wheel by
hanging the hub from the upper spokes. They don't and it doesn't.

Some who propose the gyroscope theory, also explain that the advanced
skill of making fast turns on a bicycle involves a technique they call
countersteer. In fact, a bicycle cannot be ridden without
countersteer, commonly called balance, and it is this balance that is
used to keep the bicycle upright, just as one does while walking,
running, ice skating or roller skating. To say that the gyroscopic
forces of rotating wheels keep the bicycle upright, ignores that
roller skates are operated the same way and have so little gyroscopic
moment that one cannot detect it. On ice skates the argument fails
entirely. Besides, a bicycle can be ridden at less than three miles
per hour, at which speeds there is no effective gyroscopic reaction.

Those who ride no-hands sense and make use of the small gyroscopic
effect of the front wheel to steer. This, together with trail of the
steering geometry stabilize steering. Without trail, the bicycle
would have poor straight ahead preference and would riding no-hands
difficult. Many bicyclists never master riding no-hands because the
gyroscopic forces are too small for them to detect. Hands on the
handlebars completely obscure these forces.

For those who ride no-hands, countersteer should be visible and
obvious because the bicycle must be leaned away from the preferred
lean angle and direction of a curve so that the turn can be initiated.
With hands on the bars, although the opposing lean is unnecessary,
countersteer is still needed and can be done without counter-leaning.

That there are gyroscopic forces is evident from the riderless bicycle
test in which a bicycle is shoved at a brisk speed (from another
bicycle) and allowed to coast on its own. If the initial course is
straight, the bicycle will continue this path until it slows to a
speed where gyroscopic forces are too small to correct steering. Then
the bicycle takes a steep turn as it falls.

Gyroscopic forces are also used to walk a bicycle, holding it by the
saddle and steering it to either side by quickly tilting the bicycle.
The effect can be observed by resting a road bicycle (with a
horizontal top tube) on the shoulder tilted forward just enough to
make the front wheel aim straight ahead. Spinning the front wheel by
hand forward will make it steer as one expects, left for a left tilt,
right for a right tilt, all moves performed in less than a second.
With the wheel spinning backward, all responses are reversed.

A good example of a bicycle with no gyroscopic forces is the ski-bob,
a "bicycle" with short ski runners in place of wheels. This bicycle,
having no rotating parts, is ridden downslope easily by anyone who can
ride a bicycle.

------------------------------

Subject: 9.36 Going over the bars
From: Jobst Brandt
Date: Fri, 05 Sep 1997 17:31:23 PDT

Many bicyclists fear using the front brake because they believe it, in
contrast to the rear brake, might cause the bicycle to overturn. What
is not apparent, is that overturning a bicycle with the front brake is
much harder than it seems, and that braking itself, is not the cause
of most pitchovers.

The primary cause of bicycle pitchover, is that the bicycle stops and
the rider does not, after which the bicycle overturns when the rider's
thighs strike the handlebars. Overturning can be simulated by walking
next to the bicycle, both hands on the bars, and applying the front
brake to raise the rear wheel. This experiment should make apparent
how small a force will overturn the bicycle when it stops and the
rider does not.

Beginners overturn when they use the front brake because they are not
aware that, unless they brace with their arms, only the friction on
the saddle prevents the bicycle from stopping without them. However,
even riders, who don't make this mistake, can pitchover from a
front-wheel jam that leaves no time to react. A stopped rear wheel
usually does not cause pitchover, because even if the rider moves
forward, unloading the rear wheel, effectively releases the brake.

Typically, front wheel jams occur from a stick in the spokes, a fender
jamming into the fork crown, a front cantilever straddle cable falling
onto a knobby tread, or a retaining bolt of a caliper brake releasing
from the fork crown. These are unanticipated events for which a rider
cannot brace if not already doing so. However, on clean pavement a
front wheel jam will overturn the bicycle regardless of rider reaction.

That bicycles do not easily overturn by braking becomes apparent by
attempting to raise the rear wheel, preferably at modest speed and
while bracing with the arms. The front brake, the principal stopping
and speed control device on motorcycles and cars, is especially
important for bicycles, whose short wheelbase causes even more weight
to transfer to the front wheel while braking, thereby making the rear
brake less effective. Therefore, the front brake should be understood
and used properly rather than being maligned as it is.

Formerly bicycles in the USA had their front brake on the right hand
as do motorcycles. A concerted effort by right handed safety
advocates, moved the "dangerous" front brake to the left hand, where
it could do less harm, and there it remains today.

------------------------------

Subject: 9.37 Yet another powerbar recipe
From: Dave Blake
Date: 1 Jun 1998 00:51:37 GMT

Bikewrkr wrote:
I'm getting sick of spending what seems to be all of my money on power bars,
gels, etc.

I know someone out there has their own secret sauce.


Here it is again - the Good Biscuit as tested and
raved about on rec.bicycles.tech.

Also, there is a clip in the FAQ at
http://draco.acs.uci.edu/rbfaq

I clipped this recipe about 3-4 years ago, from a
wreck.bikes newsgroup, and didn't make any of them.
The topic came up again recently, so I reposted the
recipe. And someone (please forgive me for not
remembering who) made them. And they came out well.
So then I felt really guilty, and I made some of my
own. And they came out well too. Non-cyclists at work
kept stopping by my desk to see if I had any more,
So here is the recipe. Please let me know how they turn out.

1-1/2 cup whole wheat flour
3/4 cup all purpose flour
1/2 cup brown sugar, firmly packed
1/4 cup wheat germ
0.5 teaspoon baking powder
1 teaspoon cinnamon
1/2 teaspoon salt
2 eggs
1/3 cup corn, safflower, or light olive oil
1/4 cup molasses (or equivalent mix of molasses and honey)
(the honey mix is sweeter, I find all molasses a little bitter)

1/4 cup RAW sugar (not white refined sugar)
1 tablespoon finely grated orange peel (California orange NOT Florida)
1 teaspoon vanilla
1 cup orange juice (fresh JUICED from those California oranges)

1 cup chopped dried figs (or 1.5 cups total dried fruit)
1/2 cup golden raisins (I used 1 cup figs, 0.5 dry strawberries)

1/2 cup chopped almonds (or other nuts)

Combine flours, sugar, wheat, wheat germ, baking powder, cinnamon, and
salt. In smaller bowl, blend eggs, butter, honey, molasses, orange
peel, vanilla, and orange juice with wire whip. Add liquid to dry
ingredients; whip until smooth. Add figs, raisins, and almonds.

Spread in a greased 9 x 13 inch baking pan. Bake at 350 degrees F oven
for 35 minutes, until it tests done.

Makes about 24 bars.


Dave Blake


------------------------------

Subject: 9.38 Custom Jerseys
From:

Date: Wed, 10 Nov 1999 10:22:48 PST

Does anybody know where I can find someplace that does custom jerseys
for clubs? Any ideas on how much they would cost? Please Email me at
one of the addresses below. Thanks for any help you can give me.


There are all sorts of jersey makers that you can find here or there. They
can usually be found advertising in the back of various bicycle
publications. Let's see if I can do this again:

Jerseys can be cheap -- in the neighborhood of $20 in quantities of 100 --
if you are willing to settle for one color (with perhaps some second color
trim for the sleeve and waistband piping) with a silk screened club logo.
These are the sorts of jerseys that were common in the old days. (Try Pyro
Apparel which I used and for this sort of jersey they were fine.)

Since the advent of fancy jerseys on professional teams more and more clubs
prefer to have the same sort of jerseys which use expensive high tech
materials and even more expensive coloring techniques such as sublimation
printing (where the jersey is white and the colored patterns and writing is
melted into the material permanently.)

Jerseys of this sort will run you about $60 apiece in 100's quantities from
the top line manufacturers counting all of the charges and shipping. These
would have several colors and complex artwork. (You can get this sort of
thing from Voler, VO2max, Canari, Castelli, etc.)

Top line jerseys require top line designs and if you get amateur designers
you could easily get an expensive jersey that looks like crap. So if you
don't have some good industrial designers in the club and can't afford to
get one, stay with the cheaper end of the chain.

Also quantity discounts are substantial so a large club can get very cheap
high class jerseys while a small club may actually pay more for much lower
quality jerseys.

http://www.pyroapparel.com/ (used and recommend)
http://www.voler.com/ (used and recommend)
http://www.vomax.com/ (Jazzy works for them and that's recommendation enough)
http://www.pearlizumi.com/ (Their production jerseys are some of the very best)
http://www.cannondale.com/ (They have very high quality stuff but I don't
know whether they make custom jerseys but I would imagine so for a large
order.)
http://www.sugoi.ca/team/ (It's close but these guys get my vote for top quality.)

A lot of people pop in and out of this business and its best to stick with
people who have shown that they can deliver a product on time and remain
there for years. There are also a lot of dorky clothing manufacturers that
think they can capitalize on bicycling's perceived popularity beware the
baggy shorts crowd since they can't figure out how to sew real lycra and
coolmax.

From off of the Urbanek site: (http://www.bicycleapparel.com)


What you need to know before you order Team & Club Apparel

Printed Jerseys and Team/Club Apparel

Most of the printed jerseys that you see on the market are sublimated.
Sublimation is a printing process whereby the image on a sheet of paper is
transferred onto white fabric through heat and pressure. The heat and
pressure cause the ink on the paper to turn to a gas which permanently
impregnates the fabric. The benefit of this process is that the image is
permanent and will not crack or fade like silk screening. Because the ink
impregnates the fabric and does not lay on top of the fabric like silk
screen printing, it does not interfere with the wicking properties or
breathability of the garment. The down side to this process is the expense.
Pricing is based on the number of colors in the garment and the quantity of
garments you wish to order. Each company has different minimums and pricing
policies so shop around.

Pricing is based on the number of colors and the number of garments

INFORMATION YOU WANT TO ASK
Delivery times (especially important if you have a scheduled event). The
average turn around time for a sublimation job is 6-8 weeks from the receipt
of deposit. In peak season deliveries can get behind. Order early and allow
extra time if you have a scheduled event.

Garment fit. If you are buying for a team or club, ask the company to supply
you with a size run of the garments that you wish to order and have everyone
try them on before you place your order. You will need to give the company a
deposit for the samples.

The following manufacturers make custom cycling apparel for teams & clubs.

Canari 800 929 2925
Castelli 877 324-7448
Giordana 800 366 4482
Hot Shoppe 949 487 2828
Kucharik 310 538 4611
Louis Garneau 802 334 5885
Pearlizumi 800 328 8488
Pace 800 762 7223
Parentini (39) 0571 467543
ST Cyclewear (619) 449-4300
Sugoi 800 432 1335
Voler 800 473 7814
VO Max 800 530 9740

INFORMATION THAT YOU NEED TO GIVE THE MANUFACTURER.
Before you shop... have the following information ready!

1) Quantity and style of garments that you want to order.
2) Do you have art work completed, or do you want the company to do the art
work for you?
3) How many colors are in your art work?
4) Do you want to have different art work on the front and back?

------------------------------

Subject: 9.39 Iliotibial Band Syndrome and Patelar Tendonitis
From: Tom Kunich
Date: Thu, 25 Nov 1999 22:21:41 -0800

I missed discussion earlier regarding Iliotibial Band Syndrome. I have been
having leg pain lately & the doc. told me this could be causing it. What
can other cyclists tell me about this ie, symptoms, causes, cure, avoidance
in the future?


Illiotibial Band Syndrome is caused by the bike fit all right. But it is
an overuse injury and your bike fit may not be the direct cause, but
instead be a factor contributing to retaining the injury.

The people most in danger of contracting this RARELY serious but painful
problem are short women with wide hips. However, there have been reports
from both sexes and all sizes upon occasion.

It is caused when the illiotibial band is stretched across the bony
ridge on the outside of the knee joint. Bend your knee and feel the
outside edge of your leg at the knee and that is where the pain should
be if it is am illiotibial band problem.

Another problem in the immediate area is patelar tendonitis. The pain
for this is associated more with the knee cap (patelar) than the side of
the leg/knee. PT pain is usually more towards the center of the kneecap
though mine was to the outside top of the knee cap.

Normally people who contract IBS from bike fit simply have the seat down
too low. This is also the cause of much Patelar Tendonitis.

Both problems are usually associated with a major jump in the amount of
riding or the level of riding that you have performed.

The cure for either is pretty much the same regiment:

1) As long as you have the pain do not ride hard. It is usually
recommended that you stay in the small ring. But many people can strain
just as hard in the little ring as the big. The main thing is to ride,
but to ride easy.

2) Start your ride easy and ride for about 15-20 minutes then stop and
stretch. Stretching is normally something like holding your left foot in
your right hand for 30 seconds, releasing and resting for about a minute
then repeating three times. If you can feel ANYTHING stretching you are
pulling too hard. Proper stretching is designed to return tendons to
their NORMAL length not pull them over your shoulder. Do both sides
regardless that only one is bothered. The other side will be carrying
more load than usual because you will favor the painful side.

3) Directly after your ride you must again stretch. Don't put it off
till later. There is no later in stretching. You must stretch when your
muscles are warmed up and the tendons are ready for it.

4) Immediately after you get back from your ride ice the painful area. I
just put a few ice cubes into a zip-lock plastic bag, sat down and
watched a 1/2 hour TV show. You need at least 20 minutes of icing. Some
people are sensitive to ice and then need to use a regular ice back or
wrap the plastic bag in a face cloth or some such. As long as you aren't
burning your skin, more icing is better than less.

5) As an OPTION but one I recommend, you can take over-the-counter
anti-inflammatories such as aspirin or ibuprophen. NEVER MIX pain
relievers. NEVER, NEVER mix them with Tylenol or other acetylmenophen
mixtures. Kidney failures have been known to happen when mixing these
things at package dosages. People, even doctors, are often pretty
cavalier about aspirin and the like but you should always follow the
package directions for maximum dosage and you should always consume a
lot of water when using these things. These things are dangerous to your
health if mishandled.

6) If you don't stretch you will not get better. If you don't ice you
may not get better. The important thing in fit is to get the seat height
and the handlebar reach appropriate for your body. There are other
factors in a fit that can lead to problems but you need to know
something about bike fit and this isn't the appropriate forum. Remember
that it's easier to hurt yourself stretching than just about any other
way so always use care when stretching.

7) Finally, I said that this rarely becomes serious -- but sometimes it
does. If you allow this pain to persist for a very long time it can
cause scarring of the tendon on the tibial ridge area and fixing this
can require surgery. This is not the sort of pain the you can 'ride off'
such as when you're hardening up your sit bones for longer rides. Or
when your neck hurts from bending it up in a tight aero tuck. This pain
requires you to do something about it. IF IT PERSISTS DEFINITELY GO TO A
DOCTOR SPECIALIZING IN SPORTS INJURIES OF THIS NATURE.

8) Bike fit to prevent the problem in the first place. Stretch as a
preventative measure if you are in the most likely group -- short, wide
hipped women. Stretch, ice and ani-inflammatory to rid yourself of the
problem. Ride easy until the pain is gone.

In some people the pain goes away in a week while in others it takes
months of hard work. And remember that in 99.99% of the cases the
simplest measures are the most effective.

------------------------------

Subject: 9.40 Staying up in a crash
From: "John F Tomlinson"
Date: Tue, 22 May 2001 07:37:41 -0400

I just barely avoided falling in the largish crash on the last lap of
a race a few weeks ago, and that got me thinking about the key
elements in avoiding crashing.

The first is to convince yourself of something that isn't completely
true -- that you are one hundred percent responsible for staying
upright and avoiding crashes.

Sure, in reality another rider might take your front wheel out from
under you or cause a big pile-up but, whenever you are on the bike,
you've got to believe that you are responsible for yourself. That's
the only way you can ensure you'll do your best not to fall.

I crashed in Central Park about five years ago. Another rider slammed
me from the side and we both fell off. I was vaguely aware that he was
next to me and knew he was a bad rider. So while he "caused" the
crash, I simply should not have been near him. That was my mistake.

The second element also involves attitude -- it's learning to not give
up when a crash is happening and instead to do whatever it takes to
find a way around or through it. Bikes might be falling all around
you, but you've got to have the confidence to keep fighting to find a
way out. Don't accept that you will fall.

Most importantly, don't look into a crash as it happens -- instead
look for open space and get your bike through that space. You tend to
steer your bike where you look and if your concentration is on falling
riders, you're going to get caught up in their trouble. Too many
riders see a crash, stare at it, jam on their brakes and then ride
into the crash. Instead, as soon as a crash starts you want to try to
get around it as fast as possible. It's sometimes OK to touch your
brakes for a split second to give yourself some time to find a way
around, but at racing speeds you're rarely going to actually avoid a
crash by stopping. Instead just look for open space on either side of
the crash and go for it. You might even want to accelerate into the
open space before the crash spreads.

I really can recall almost nothing about the crash a few weeks ago.
Bikes started flying around in front of me and the next thing I knew I
was looking for clear space. At first that space seemed to get farther
and farther away as the crash got bigger and bigger but, eventually, I
got through at the very edge of the road. I never looked at the actual
crash.

It's possible to practice focusing on open space by using a similar
technique to deal with potholes on training rides -- as soon as you
see one, don't look at it. Look for smooth road. With time this will
become second nature.

Fourth, whenever riding, keep a broad focus and stay aware of what's
going on around you. Don't stare at the rider in front of you but
instead look further ahead. The faster you're going, the further ahead
your focus should be.

This broad focus will often enable you to deal with trouble before it
even starts. You'll see people getting squirrelly or the road clogging
up on one side and be prepared to deal with it. Recognize too that in
much the same way as you want to accelerate around crashes, you often
should accelerate around trouble. Move up in the field before the road
gets narrow. Get to a difficult corner at the head of the group rather
than in the middle. Try to rely less on your brakes. Don't ride around
in group rides or races with your hands on the brakes. Learn to deal
with trouble by getting past it, not by just slowing down.

This sort of "aggression" is important not only to placing well but
also to your safety.

Fifth is what lots of people talk about, but too few do -- work to
improve your bike handling skills while on training rides. Some of
these skills are to make you a smoother, more predictable rider.
Others are to enable you to deal with situations in races where other
riders, intentionally or not, try to take your space. Both types of
skills are important.

Learn to keep your upper body relaxed. Gain an understanding of how
you use your hands, butt and feet to steer the bike. Practice
cornering, riding on bad roads and bunny-hopping so you'll be lighter
on the bike. Practice pacelines and ride closer and closer to other
riders. Practicing bumping into other riders and touching wheels is
good too -- you might want to start learning this while riding slowly
on a grassy field. Learn about protecting your front wheel and
handlebars. Riding off-road, on any kind of bike, can improve your
bike handling. Elizabeth races cyclo-cross in the off-season, which is
great for skills.

There are a lot of details to bike handling that I won't go into here;
formal coaching sessions or club rides are a good place to start.

You can also use other sports to improve your balance and body
awareness. Skiing, skating, soccer, basketball and dance are good.
(Motorcycling is supposedly great.)

Sixth, make sure your bike is in good working order. It should be
reliable and fit your body well. Your weight should be properly
distributed over the two wheels -- with just slightly more weight on
the back wheel than the front when riding in the drops.

Finally -- be aware of your limits. Crashes often happen when riders
are tired and get sloppy. They don't pay attention to what's going on
around them and their reactions slow. If you find yourself fighting
with the bike and riding with your head down, make a conscious effort
to relax and keep your eyes up. If you can't do that, back off from
the race -- you're a danger to yourself and others. As you improve as
a racer you'll find you get better at staying alert and in control
even when very tired.

Your limits are not only physical, but technical and mental too.
Learning and improvement come from pushing the boundaries of what
you're comfortable and proficient at. Bike racing is supposed to be
difficult and a small amount of fear is normal. But if you're
consistently stressed about crashing, or spending time constantly
riding your brakes due to fear, it might be worth backing off in the
race and giving yourself some space, even if you get dropped. A lot of
times when I'm scared I ride right at the front, or go way to the back
where there is more space until things calm down. Later, you can work
on your skills and confidence so that in the next race, you'll be more
in control.

------------------------------

Subject: 9.41 Applying Merlin Decals
From: Mark Hickey

Remove the old decals completely (including any residue). There
shouldn't be any clear coat on top of the decals (hey, it's a ti
bike). I'd suggest cleaning the tube with acetone or other solvent to
make sure it's clean.

Peel the heavy paper backing (I'll bet it's green) off the decal.

Place the decal VERY CAREFULLY in place, starting with the top making
contact.

VERY CAREFULLY rub down the decal so it makes contact with the frame
(you'll be able to see where this is happening).

Once the decal is placed on the frame, vigorously rub the decal with a
clean rag to create some heat (start slowly to keep from wrinkling the
decal).

When you're done, lightly "squeegee" over the decal with the edge of a
credit card or something similar. You'll see the decal release from
the backing as this happens.

If you end up with an air bubble, you can usually pierce the decal and
squeeze the air out (with the backing still in place, or "reapplied".

It takes a few days for the decals to reach full strength (they dry
from the outside in). Be careful with 'em during that period.

Mark Hickey
Habanero Cycles
http://www.habcycles.com

------------------------------

Subject: 9.42 Flats from beer and cigarettes
From: Jobst Brandt
Date: Tue, 16 Sep 1997 11:10:32 PDT

Flat tires are caused by beer in winter and by cigarettes in summer.
As odd as this may seem, there is a direct link.

Glass is visible on roads by its shiny splinters and shards as well as
not being the same color as the road. When wet from rain, these
characteristics vanish and leave glass looking like any bit of gravel.
Not only is it "invisible" but it is lubricated and cuts through
rubber effortlessly. A convincing experiment is to cut a thick rubber
band with a razor, first dry, then wet.

In summer flats are caused by puncture vine thorns, a plant that grows
only on barren soil. There isn't much of that around except
peculiarly on roadsides that have been sprayed to prevent grass from
growing, grass that when dry presents a fire hazard for cigarettes
discarded from cars. Puncture vine grows on these barren roadsides
that have been created for safer cigarette disposal. If roadsides
were not sprayed, puncture vine would be a rare occurrence along roads
where bicyclists most often ride.

http://www.cwma.org/puncturevine.html
http://www.or.blm.gov:80/Prineville/weed/puncture.htm
http://tinyurl.com/d0xo

------------------------------

Subject: 9.42 Riding on Ice
From: Jobst Brandt
Date: Fri, 13 Feb 2004 12:07:59 -0800

Ice riding is best done with studded tires of which there are a few
suppliers, mainly in northern Europe, such as Nokian:

http://www.nokiantyres.fi/bike/winter/index.html

Riding on ice, especially frozen lakes, requires a few practical
tricks. This applies to slick as well as studded tires. Ice, in
contrast to fresh snow, is slick no matter whether it is frozen water
or firmly compacted snow. It offers poor traction. Therefore, riding
on ice should be done in top gear to avoid rear wheel spin. This is
similar to driving cars with manual transmissions where starting in
second gear helps avoid wheel spin. For bicycling on level ice, top
gear is best for both starting and cruising, because while starting,
acceleration is the main force while once rolling, wind drag, even at
low speeds, readily exceeds traction.

In the absence of studded tires for frozen lakes without a snow crust,
slick tires are better than ones with miniature automobile tread
because they give more contact surface, thereby reducing contact
pressure and slip.

Braking with the front wheel is impractical for two reasons. Skidding
the front wheel usually causes a fall, and there is no way to detect
that the front wheel is skidding except by falling. In contrast, rear
wheel skidding is benign and it can be easily detected. By continuing
to pedal while braking enables a precise ABS. When the rear wheel
skids, the pedals stop suddenly, to which one can respond almost
instantly by letting up the brake. The response speed and precision
of this method is surprising.

Good gloves help not only against the cold, but with inevitable
falling, they protect the hands from the ice. Frozen lakes are a
wonderful way to appreciate landscapes where there is no alternate
route and is safer than riding with traffic on icy streets. Thin ice,
a term heard often with risky adventures, is a hazard that occurs from
currents and from convection caused by gas bubbling to the surface in
marshy areas. Stay away from reeds and swamps.

Water in a frozen lake is at 4C (39F), its greatest density because
colder water rises to the surface and begins to freeze while warmer
water rises to the surface and cools. Marsh gas bubbling to the
surface brings 4C water to the surface to melt ice causing thin hollow
domes that no longer contact the water.

Thin spots can be detected if the surface is clear ice but they
present a hazard just the same. The bubble method is used to protect
boats too large to be lifted from the water. It keeps an opening in
the ice from an under water bubbler pipe in the shape of the hull.

http://tinyurl.com/ttp6

------------------------------

Subject: 10 Off-Road

------------------------------

Subject: 10.1 Suspension Stems
From: Brian Lee

by Brian Lee & Rick Brusuelas, 1994

ABSTRACT: Discussion of the differences between suspension stems
and suspension forks, and a listing of the pros & cons of suspension
stems.

DESCRIPTION: The suspension stem discussed here is the
Allsop-type, which employs a linkage parallelogram and a spring
mechanism to effect shock-absorption. Two models on the market
using this mechanism are the Allsop Softride, and a version
produced by J.P. Morgen, a machinist based in San Francisco.
There is also a version put out by J.D Components of Taiwan
(advertised in Mountain Bike Action), however judging from
illustrations, this unit does not employ the parallelogram design
shared by Allsop & Morgen. Other Taiwanese models may also exist.
The Girvin-type stem, which uses a simpler hinge and bumper, will
not be directly addressed here, although some of the comments
may also apply.

The Allsop-type suspension stem (suspension stem) works on a
different principal than a telescopic shock fork. Instead of
only the front wheel moving to absorb shock, a stem allows the
entire front end of the bike to move with obstacles while the
rider's position does not change.

All suspension requires some form of "inertial backstop" to
operate. A theoretical suspension (stem or fork) loaded with
zero mass will not function regardless of the size of obstacle
encountered. This is because there is nothing to force the
compression of the spring mechanism. It is essentially locked
out.

In a fork system, the weight of the bike & rider both provide the
inertial backstop. In a stem system, the rider's weight on the
handlebars provides the backstop. Because of this, the two
systems "ride" differently.

Since most of the weight comes from the pressure of the rider's
hands, the stem system encourages a more weight-forward style of
riding. Or perhaps placing the stem on a frame with a shorter
top tube so the rider's weight is distributed more on the front
end. (Shortening the front end has also been applied by frame
builders on frames intended for use with suspension forks. Ex:
Bontrager.)

What does this mean to you and me? It means the suspension stem
requires a certain amount of the rider's weight to be on it at
all times in order to remain completely active. For the majority
of riding, it's just fine. The only difference is in extremely
steep descents, where you are forced to keep the weight back in
order to keep from going over the bars.

In this situation, much less weight is on the bars to activate
the stem. Further, if one were to encounter a largish rock on
such a descent, what does one do? The instinctive thing is to
pull back a bit to unweight the front and help the front wheel
over. This removes all the weight from the stem area, and you
are now riding a rigid bike again.

A fork system is also affected by weight shifts, but not quite to
the extent that a stem is affected, because of the weight of bike
& rider coming through the head tube to be distributed into the
fork. Even if you were to remove your hands from the bars on a
gnarly descent and hang with butt brushing the rear wheel, you
are still applying weight to the bike through the pedals.

All this, of course, is theoretical and YMMV. I, for one, am not
always able to react to obstacles coming at me and leave the
front end weighted. When that happens, I'm very glad I have
suspension.

Now enough theory stuff, here's a summary of the advantages &
disadvantages of suspension stems:

PROs

1) Lighter than a suspension fork. This depends on the existing
stem/fork combination. If the current stem and rigid fork are
heavy, then a suspension fork may be a better choice. For
example, I've chosen the following items for comparison, as they
represent the lightest and heaviest of commercially available
stems & forks (weights for all stems are for conventional types -
non-Aheadset):

Litespeed Titanium 211g
Ritchey Force Directional 375g
Allsop Stem 625g
Fat Chance Big One Inch 680g
Tange Big Fork 1176g
Manitou 3 1360g
Lawwill Leader 1588g

So say you have a Litespeed stem and a Fat Chance fork. The
combined weight would be 891 g. Switching to an Allsop would
change the combined weight to 1305 g, while a Manitou 3 would
bring it to 1571 g. The Allsop has a weight advantage of 266 g
(9.4 oz).

OTOH, if you have a Ritchey stem & Tange Big Fork, the original
weight would be 1551 g. Allsop stem = 1801 g. Manitou 3 = 1735
g. In this case, keeping the boat anchor of a fork and switching
to the Allsop would be a weight penalty of 66 g (2.3 oz.).

Of course, YMMV depending on your original equipment.

2) Does not affect frame geometry. A suspension fork
retrofitted to a frame, *not* designed for suspension, raises the
front end - sometimes as much as 1". This reduces the effective
head angle and slackens the steering, slowing it down. This is
especially true for smaller sized frames which, with their
shorter wheel base, are affected to a greater degree by the
raising of the head tube. A suspension stem provides suspension
while preserving the handling of the bike.

3) Torsionally rigid fork. Telescopic forks all have a certain
amount of flex to them, and the sliders are able to move up &
down independently. This aspect of front suspension forks has
spawned a new line of suspension enhancing products: stiffer
fork braces, and bigger, heavier suspension hubs. All to stiffen
up the fork. This is one reason suspension stems are favored by
some riders who ride lots of tight, twisting single track.

4) No stiction. Stiction, or static friction, is friction that
exists as the fork sliders rub against the stanchion tubes.
This friction is an extra force that must be overcome for a fork
system to activate. Not a problem on large hits. But more of a
problem on small- and medium-size impacts. Because the stem has
none, the stem responds better to small, high-frequency bumps
(washboard) than many air-oil forks.

5) More boing for the buck. The Allsop stem provides up to 3"
of stiction-free travel, at a cost of about $250, depending
where you go. The majority of forks in this price range only
offer 1" - 2" of travel, and are often heavy, flexy, and fraught
with stiction. The fork could be stiffened, but at the
additional cost of a stiffer fork brace or perhaps a suspension
hub and a rebuilt wheel (e.g. fork brace - $90; hub - $80;
rebuild - $100. Plus the original $350 for the fork. YMMV).

6) Better "feel". The stem allows you to have a rigid fork,
which transmits more "information" back to the rider. This is a
benefit when riding through creeks where you cannot see where
your wheel is.

7) Less exposed to the environment. The stem is higher, more
out of the way than suspension forks. Thus you can ride through
creeks and mud without having to worry about your fork seals, or
about contaminating the innards of the fork. Even if mud
splashes on a suspension stem, the pivots are less sensitive to
grit than sliders and stanchion tubes.

8) Ease of maintenance. There are no seals to replace or
service, no oil to replace, no air pressure to adjust, and no
bumpers to wear out. An occasional lube of the pivots is all
that is needed. An extension of this is the ease of initial set
up. For best results, you have to set suspension (fork or stem)
to react according to your weight and riding style. With air/oil
forks you may have to change oil, adjust pressure or change
damping settings (if the fork has them). With bumper forks you
may need to swap out bumper stacks and mix-n-match bumpers until
you get what works for you. With the stem, the only adjustment
is to increase or decrease the spring tension with an allen
wrench.


CONs

1) No damping. This is one of the main complaints from
proponents of suspension forks. The suspension stem will give
way to absorb shock, but the return is not controlled and cannot
be adjusted. JP Morgen currently makes a suspension stem which
employs oil-damping, but Allsop does not.

2) Requires adjustment to riding style. As mentioned above, the
stem requires weight to be applied to it to function. This is
also one of the complaints applied to the Softride rear
suspension beam. The flip-side to this, according to riders of
the Beam, is once the adjustment is made to "plant your butt on
the saddle" the ride is extremely comfortable and affords
excellent control by sticking the rear tire to the ground.

3) Stem "clunks" on rebound. The feeling is about the same as
suspension bottoming out, except it happens on the rebound. This
is not as much a problem on the Allsop as on the Morgen stem,
which uses a hard plastic top-out bumper. This is a subjective
complaint, as some riders claim not to notice it.

4) Stem not torsionally rigid. Another trade off. The stem is
not proof to twisting forces and may be noticeable in hard,
out-of-the-saddle efforts. Allsop has redesigned the top beam of
their aluminum stem for 1994 to address this problem. Instead
of the aluminum "dog bone" structure for the top linkage member,
they've substituted a machined aluminum beam, reminiscent of a
cantilever bridge.

SUMMARY: In my opinion, a suspension stem is an excellent choice
if one is retrofitting an existing bike, which has not been
designed around a suspension fork. A suspension stem is also a
very good choice if one's primary riding is twisty singletrack,
where you need the sharp, precise steering of a rigid fork.
There are undoubtedly situations for which a stem may not be
ideal, but stems should not be dismissed as a viable form of
suspension. The best thing to do is to try both types of
suspension if you can, and see what you like better.

------------------------------

Subject: 10.2 MTB FAQ available
From: Vince Cheng

The MTB FAQ from the above author is no longer available.

------------------------------

Subject: 10.3 Installing new rear derailleur spring
From: Alan C Fang
Date: Tue, 20 May 1997 12:27:07 -0700 (PDT)

leave the derailler on the bike. first, check the orientation of the old
spring so that you will know how to put in the new one. taking out the
old spring shouldn't be too hard- just yank on it. if you can't do it,
use the reverse of what i'm about to tell you for getting the new spring
in.

one end of the spring is open. that open end has to hook onto this bar on
the derailler body. to get it up and over this bar, get a piece of brake
or shifter cable (or a strong string) and bend it in half, putting a kink
in it. put the spring inside the derailler in the proper orientation.
thread this kink through the derailler where the bar is, making it go on
the side of the bar opposite the open side of the spring's hook. hook the
kink in the cable around the open end of the spring, and yank on the
cable. that should pull the open end of the spring past the bar. now you
can stuff the tip of the hook back over the bar, thus hooking the
derailler spring onto the bar.

the closed end of the spring is much easier to get in. what i use is a
bottom bracket tool, the kind with the pins for adjusting older style
bb's. use one of the pins to grab the closed end of the spring, and lift
it up so that it hooks onto that [other thing]. you are done. voila! or
as a dyslexic would say, viola!

------------------------------

Subject: 10.4 A Brief History of the Mountain Bike
From: Jobst Brandt
Date: Fri, 13 Feb 2004 12:07:59 -0800

The first -successful- high quality fat-tire bicycle was built in
Marin County, California by Joe Breeze, who recognized a demand for
such a bicycle while riding with friends on the rocky trails of nearby
Mt Tamalpais. They used balloon-tire one-speed bicycles from the
1930s, 1940s and 1950s (Schwinn Excelsior) with New Departure and
Bendix coaster brakes. These brakes were the origin of the name
"Repack" for one of the trails, because one descent was enough to
overheat the hub brake, requiring it to be re-packed. They referred
to their Mt. Tamalpais downhill bicycles as "my mountain bike" in
contrast to "my road bike" without giving the term generic
significance. According to Joe Breeze, riders around Santa Barbara
also used the term for their fat tired trail bicycles.

Joe Breeze, Otis Guy, and Gary Fisher, all still in the bicycle
business today, were top category USCF riders. Many of the Tamalpais
riders were members of road racing Velo Club Tamalpais, whose blue and
gold jersey carried the Mt. Tamalpais silhouette logo. In October of
1977, Joe built a fat-tire bicycle of lightweight tubing that was
previously found only on better road racing bicycles. It had all new,
high-quality parts and 26" x 2.125" Uniroyal "Knobby" tires on Schwinn
S2 rims and Phil Wood hubs. Joe built ten of these first Breezers by
June 1978. Breezer #1 has been on display at various places,
including the Oakland Museum, where it has been on permanent display
since 1985.

However the first Breezer was predated by a frame built for Charlie
Kelly by Craig Mitchell earlier in 1977. As the Breezer frames that
followed, it was made of 4130 chrome-molybdenum airframe tubing.
Charlie equipped it with the parts from his Schwinn Excelsior
including SunTour derailleurs and thumb shifters, TA aluminum cranks,
Union drum brake hubs, motorcycle brake levers, Brooks B-72 saddle,
Schwinn S-2 rims and UniRoyal Knobby tires (essentially, the best
parts found on clunkers of that day). In spite of this, he chose to
switch back to his Schwinn frame, which he rode until June of 1978,
when he got himself a Breezer, and for one reason or another the
Mitchell frame was not further developed.

In January 1979, Joe and Otis, who were planning another tandem
transcontinental record attempt, visited Tom Ritchey, who was building
the frame, and brought along Joe's Breezer mountain bike. Peter
Johnson, another noted frame builder who happened to be present, was
impressed with its features, as was Tom, sensing the significance of
the concept, both being veteran road bike trail riders in the Santa
Cruz mountains. Gary Fisher got wind of Tom's interest in fat tire
bikes and asked Tom to build him one. Tom built one for himself, one
for Gary, and one for Gary to sell.

After building nine more frames later in 1979, Tom couldn't find
buyers for them in nearby Palo Alto, so he asked Fisher if he could
sell them in Marin. Fisher and Charlie Kelly pooled a few hundred
dollars and started "MountainBikes" which became today's Gary Fisher
Bicycles. It was the first exclusively mountain bike business. It
was Tom's bikes, and Fisher and Kelly's business that made the
introduction of the mountain bike take hold. This was an obvious gap
in the bicycle market, most builders focusing on road bikes, left this
as an open field for innovation.

Fisher and Kelly tried to trademark the name Mountainbike, but through
procedural or definition errors the application was finally rejected.
Meanwhile in the 1980's Bicycling Magazine had a "name that bike"
contest that excluded the name "Mountainbike", that name being before
the trade mark board at the time. ATB was the winner but it didn't
hold ground against the much more natural "Mountain Bike" name that
spread rapidly after the trade mark application failed.

If anyone's name stands out as the builder of the earliest viable
mountain bike, it is Joe Breeze, who today still produces Breezers.
The marketing push first came from Tom Ritchey, Gary Fisher, and
Charlie Kelly and the ball was rolling. At first the USCF felt it
below their dignity, as did the UCI, to include these bicycles, but
after NORBA racers began to outnumber USCF racers, they relented and
absorbed these upstarts, as they certainly would recumbents if they
had similar public appeal.

------------------------------

Subject: 10.5 The Mike Vandeman FAQ
Date: Tue, 29 Jul 1997 20:49:05 PDT

The old Mike Vandeman FAQ is no longer available.

------------------------------

Subject: 10.6 Ode to a Usenet Kook
From: (Trekkie Dad)
Date: Mon, 30 Nov 1998 16:10:38 -0800

[previously posted on alt.mountain-bike]

Ode to a Usenet Kook

Do you like my mountain-bike?
Do you like it? Do you, Mike?

I do not like your mountain-bike.
Leave it home! Go for a hike!
Too many gears! Enormous treads!
You rip my favorite trails to shreds!
You may not ride it here or there,
You may not ride it anywhere!

May I ride on single-track
with all my gear in camelbak?

You may not ride on single-track
with mountain bike or camelbak
And do not ride on fire-road,
It cannot take the overload.
You may not ride it here or there,
You may not ride it anywhere!

Where may I ride my new hardtail;
The one that's made by Cannondale?

You may not ride your new hardtail,
be it Trek or Cannondale.
You may not ride on single-track
With mountain bike or camelbak.
I do not like your mountain-bike.
Leave it home! Go for a hike!

Where may I ride my plush GT
With seven cogs and chainrings three?

You may not ride that plush GT,
in habitat that's human-free
It never will be allowed, you see
I want to save the woods! (for ME)

Stay off the trails for heaven's sakes,
Your knobby tires are killing snakes.
It's known to all biologists,
And famous herpetologists.
We do not like your mountain-bike!
Leave it home! Go for a hike!
You may not ride it here or there,
You may not ride it anywhere!

But, mikey, you don't understand
Enlightened people manage land.

So I will ride my mountain-bike,
I'll go on wheels. You take a hike!
And I will ride it here and there,
And I will ride it everywhere.

I will ride on single-track
With fully-loaded Camelbak.
And I will ride on fire-road,
It isn't such a heavy load!

I will ride that new hardtail;
the one that's made by Cannondale,
And I will ride my plush GT
(There is no place that's "human-free")

A little skill is all it takes
To keep from killing whippersnakes.
And we all know your PhD
Is NOT in herpetology.

--
Trekkie Dad | ICQ #14818568 |

World Without Cars Dictionary (updated November 27, 1998) at
http://www.geocities.com/yosemite/rapids/2356/wwc.html

------------------------------

Ads
 

Home - Home - Home - Home - Home