A Cycling & bikes forum. CycleBanter.com

Go Back   Home » CycleBanter.com forum » rec.bicycles » Techniques
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Aluminum bikes



 
 
Thread Tools Display Modes
  #21  
Old July 10th 19, 01:58 PM posted to rec.bicycles.tech
AMuzi
external usenet poster
 
Posts: 13,447
Default Aluminum bikes

On 7/10/2019 12:36 AM, AK wrote:
On Tuesday, July 9, 2019 at 7:44:09 PM UTC-5, Tom Kunich wrote:
On Monday, July 8, 2019 at 5:56:40 PM UTC-7, Ralph Barone wrote:
wrote:
On Monday, July 8, 2019 at 1:58:38 AM UTC-5, AK wrote:

I did not see any mention of how to find the leak. :-)

Suppose I could carry a small spray bottle of soapy water


The VAST MAJORITY of the time it is very easy to find a leak in a tube.
You inflate it and hold it up to your ear and/or cheek. You will hear or
feel the air coming out. ONLY in very rare instances do you need water
and/or the soap bubbles to find a leak. And then its a very slow leak
that you could easily get home riding. Just stop every couple miles and
pump it up again. Its a very, very slow leak so will hold air for awhile.


Replace the tube and fix it when you get home (but make sure there’s no
shrapnel left in the tire first).


I had a flat on my tubeless this morning. Pumped it up, went in and coming out it was flat again. I pulled out the other bike and it had my Look Keo Blades on it and my shoes fit Delta. Changed the pedals. Returning from the ride I decided that the flat was from the sealant drying up as they do after several months.

Took a bottle of sealant and injected about an once and a half and pumped the tire up. All is AOK.

Took the chains off both bikes. One of them needed tossing and I had a spare new chain. I have this solution that would take the paint off of a battleship so I put the chains in it. First the new one since it cuts that new chain grease off and you can't even see any results. Replaced it, used some liquid wax on it and all is well. Discovered I have a set of Delta pedals that are the same weight as the Keo Blades. The problem was that whoever I bought them from must have been using them for cyclocross and the bearings were goners. I had another set of Look 226's and pulled the shaft and bearing out of those, cleaned the internal rollers with Triflow and installed them working like new again.

The old chain was black even though I had cleaned it with Rock and Roll a week ago. Put it in that solution and waited 20 minutes and rinsed it off and it looked like a new chain. Measure it for wear but it is a gold chain and they hardly wear. None detectable. Installed, waxed and left it to dry.

Made a hot dog and am ready to go re-watch the TdF. Where's my beer?


Do not know what TdF is. Maybe you can enlighten me.

I bought a tube of Easy Lube by White Lightning bicycle lubricant a couple of weeks ago.

Have not had a chance to use it yet.

Since covering my bike with a tarp, the rusting of my chain has dropped considerably.







Do not know what TdF is. Maybe you can enlighten me.


https://www.letour.fr/en/

--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


Ads
  #22  
Old July 10th 19, 03:16 PM posted to rec.bicycles.tech
Tom Kunich[_5_]
external usenet poster
 
Posts: 1,231
Default Aluminum bikes

On Wednesday, July 10, 2019 at 1:13:26 AM UTC-7, wrote:
On Tuesday, July 9, 2019 at 7:44:09 PM UTC-5, Tom Kunich wrote:
I had a flat on my tubeless this morning. Pumped it up, went in and coming out it was flat again. Returning from the ride I decided that the flat was from the sealant drying up as they do after several months.

Took a bottle of sealant and injected about an once and a half and pumped the tire up. All is AOK.


I think Chalo had a post recently about all the hassle of using tubeless. You just confirmed what he wrote.




Took the chains off both bikes. One of them needed tossing and I had a spare new chain. I have this solution that would take the paint off of a battleship so I put the chains in it. First the new one since it cuts that new chain grease off and you can't even see any results. Replaced it, used some liquid wax on it and all is well.


So you removed the best chain lube, applied in the best way possible at the factory.




Measure it for wear but it is a gold chain and they hardly wear.


You honestly believe "gold" chains hardly wear? Do you think the gold plating, coloring, is somehow extra hard to resist wear? Or is it far more likely "gold" chains don't wear because they are so pretty that you never ever ride that bike and keep it hanging up in the living room all pretty as a trophy. With the "gold" chain.


Please tell me that you aren't stupid enough to think that they actually use gold. You are missing a few links of a full chain.
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Aluminum [email protected] General 0 March 6th 08 02:02 PM
Titanium vs aluminum. ntappin Unicycling 17 September 6th 06 11:49 PM
Welding An Aluminum Rim Kenny Techniques 9 April 10th 05 12:05 AM
Aluminum Bar Ends [email protected] Marketplace 0 March 6th 05 12:44 AM
Old steel vs. new aluminum Beans Baxter General 28 June 3rd 04 08:55 PM


All times are GMT +1. The time now is 07:29 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CycleBanter.com.
The comments are property of their posters.