|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Weinmann pivot bolt required
I'm rebuilding an old 80's Raleigh racer. Unfortunately a brake pivot
bolt has sheared. Does anyone have one of these knocking about they might be willing to bung in the post? I'd be awfully grateful. If you think you might I'll stick a photo & dims up of the little rascal. Cheers, Mike W |
Ads |
#2
|
|||
|
|||
Weinmann pivot bolt required
On Sun, 1 Jun 2008 02:56:14 -0700 (PDT)
visionset wrote: I'm rebuilding an old 80's Raleigh racer. Unfortunately a brake pivot bolt has sheared. Does anyone have one of these knocking about they might be willing to bung in the post? I'd be awfully grateful. If you think you might I'll stick a photo & dims up of the little rascal. Grab these quick" http://cgi.ebay.co.uk/ws/eBayISAPI.d...m=250252553204 |
#3
|
|||
|
|||
Weinmann pivot bolt required
visionset wrote:
I'm rebuilding an old 80's Raleigh racer. Unfortunately a brake pivot bolt has sheared. Does anyone have one of these knocking about they might be willing to bung in the post? I'd be awfully grateful. If you think you might I'll stick a photo & dims up of the little rascal. Sorry I don't have a spare bolt or brake. This could be an excuse to fit dual-pivot brakes for better braking. A used set off Fleabay wouldn't be too expensive. ~PB |
#4
|
|||
|
|||
Weinmann pivot bolt required
visionset presented the following explanation :
I'm rebuilding an old 80's Raleigh racer. Unfortunately a brake pivot bolt has sheared. Does anyone have one of these knocking about they might be willing to bung in the post? I'd be awfully grateful. If you think you might I'll stick a photo & dims up of the little rascal. Centrepull or sidepull? I might have a front sidepull bolt I could spare, I think. -- Simon |
#5
|
|||
|
|||
Weinmann pivot bolt required
On 1 Jun, 17:08, Simon D wrote:
visionset presented the following explanation : I'm rebuilding an old 80's Raleigh racer. Unfortunately a brake pivot bolt has sheared. Does anyone have one of these knocking about they might be willing to bung in the post? I'd be awfully grateful. If you think you might I'll stick a photo & dims up of the little rascal. Centrepull or sidepull? I might have a front sidepull bolt I could spare, I think. -- Simon Side Pull. That'd be fantastic if you felt you could spare it. I'll go and take a photo & measure so you don't waste your time. Cheers, Mike W |
#6
|
|||
|
|||
Weinmann pivot bolt required
visionset used his keyboard to write :
Side Pull. That'd be fantastic if you felt you could spare it. I'll go and take a photo & measure so you don't waste your time. I'm pretty sure I have one, and you can certainly have it it I have. Post a picture by all means, although I think they were all pretty much the same. I won't have any nuts, but they're just a standard 10mm job.I'm really busy at the moment, but if I have a chance I'll take a look tomorrow. Failing that, it may be next week. I'll do my best. -- Simon |
#7
|
|||
|
|||
Weinmann pivot bolt required
"visionset" wrote in message ... I'm rebuilding an old 80's Raleigh racer. Unfortunately a brake pivot bolt has sheared. Does anyone have one of these knocking about they might be willing to bung in the post? I'd be awfully grateful. If you think you might I'll stick a photo & dims up of the little rascal. I've got a pair of Weinmann type 730's in decent condition you can have. Send me an email with your address to and I'll pop them in the post for you. Tom |
#8
|
|||
|
|||
Weinmann pivot bolt required
On 1 Jun, 23:04, Simon D wrote:
visionset used his keyboard to write : Side Pull. That'd be fantastic if you felt you could spare it. I'll go and take a photo & measure so you don't waste your time. I'm pretty sure I have one, and you can certainly have it it I have. Post a picture by all means, although I think they were all pretty much the same. I won't have any nuts, but they're just a standard 10mm job.I'm really busy at the moment, but if I have a chance I'll take a look tomorrow. Failing that, it may be next week. I'll do my best. -- Simon I have PM'd you my details, let me know if you haven't got them. Thanks again. Mike W |
#9
|
|||
|
|||
Weinmann pivot bolt required
visionset presented the following explanation :
On 1 Jun, 23:04, Simon D wrote: visionset used his keyboard to write : Side Pull. That'd be fantastic if you felt you could spare it. I'll go and take a photo & measure so you don't waste your time. I'm pretty sure I have one, and you can certainly have it it I have. Post a picture by all means, although I think they were all pretty much the same. I won't have any nuts, but they're just a standard 10mm job.I'm really busy at the moment, but if I have a chance I'll take a look tomorrow. Failing that, it may be next week. I'll do my best. I have PM'd you my details, let me know if you haven't got them. Thanks again. I haven't received any message. Sorry to have not got back to you before (busy). Contact me at simondaw (at) msn.com if you still need the bolt, which I have now located. -- Simon |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
brake pivot bolt/nut engagement | John Forrest Tomlinson | Techniques | 3 | July 9th 07 12:02 PM |
Cantilever pivot bolt threading | Andrew Karre | Techniques | 2 | May 12th 05 04:17 PM |
WTB: Centering bolt for dual pivot brakes | Tim Lines | Marketplace | 0 | March 3rd 05 01:36 AM |
WANTED: Weinmann/Rigida Zac 19 Rim | [email protected] | Marketplace | 0 | February 10th 05 03:43 AM |
wtb Weinmann aero brake levers | James Placer | Marketplace | 0 | July 26th 03 07:57 PM |