|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Recovering Saddle
I've got a saddle that is very comfortable but has a sort of artificial suede cover that I don't believe is going to last long if the seat is used very much. I can buy a "seat cover" with draw strings to tighten it up but I am looking for a more permanent solution... and one that doesn't look so muck like a kludge, if truth be told. I've seen a number of "re-cover your saddle" articles on the web and it looks pretty straight forward but has anyone actually done this? And if so are there any things that are a bit tricky that one needs to take into consideration? -- Cheers, John B. |
Ads |
#2
|
|||
|
|||
Recovering Saddle
I did it once, long ago. Actually, I was customizing a hard plastic bodied
saddle. I drilled a few holes in the places my sit-bones hit to give it some more flex, and built up cushioning lumps using RTV silicon. Then I stretched and glued a new leather cover over the saddle. IIRC, I used contact cement. It wasn't difficult, and it worked very well. The saddle's still good, although I haven't been using it for quite a while. - Frank Krygowski |
#3
|
|||
|
|||
Recovering Saddle
On Fri, 20 Jan 2017 20:16:37 -0800 (PST), Frank Krygowski
wrote: I did it once, long ago. Actually, I was customizing a hard plastic bodied saddle. I drilled a few holes in the places my sit-bones hit to give it some more flex, and built up cushioning lumps using RTV silicon. Then I stretched and glued a new leather cover over the saddle. IIRC, I used contact cement. It wasn't difficult, and it worked very well. The saddle's still good, although I haven't been using it for quite a while. - Frank Krygowski Do you remember any problem in laying the covering smoothly over the contact cement. -- Cheers, John B. |
#4
|
|||
|
|||
Recovering Saddle
On Saturday, January 21, 2017 at 12:01:47 AM UTC-5, John B. wrote:
On Fri, 20 Jan 2017 20:16:37 -0800 (PST), Frank Krygowski wrote: I did it once, long ago. Actually, I was customizing a hard plastic bodied saddle. I drilled a few holes in the places my sit-bones hit to give it some more flex, and built up cushioning lumps using RTV silicon. Then I stretched and glued a new leather cover over the saddle. IIRC, I used contact cement. It wasn't difficult, and it worked very well. The saddle's still good, although I haven't been using it for quite a while. - Frank Krygowski Do you remember any problem in laying the covering smoothly over the contact cement. -- Cheers, John B. Hi again John. The two great things about not gluing the entire cover to the old saddle are #1 it's a lot easier to stretch the leather and #2 you have lots of time to do that. what I did was glue the leather to one side on the inside of the old saddle shell and let that cure. I do find that cyanoacrylic glue is a lot faster but you don't have the same working time as you do with a good quality contact adhesive/cement. Plus you have to be more careful. With a contact cement you can glue that one side and when cured you can then stretch the new leather (or vinyl) cover over to the oppsite side and mark on the inside of the leather where the contact cement needs to go. Then you apply the contact cememt to the leather and to the inside of the saddle shell and then take your time stretching the leather over the shell. With contact cement you can in need to pull the leather away from the shell if there's a wrinkle and then stretch the leather both side to side and lengthwise to eliminate any wrinkling. I found the thin leather I used could stretch a fair bit in either direction. I also found that if the new leather covering was stretched moderately that it did not wrinkle in use. If concerned about the contact cemented edges coming loose you can then stich the leather to the bottom sides of the saddle shell by drilling small holes through the leather and saddle shell and then stiching the leather to the shell too. Cheers |
#5
|
|||
|
|||
Recovering Saddle
On Fri, 20 Jan 2017 21:19:41 -0800 (PST), Sir Ridesalot
wrote: On Saturday, January 21, 2017 at 12:01:47 AM UTC-5, John B. wrote: On Fri, 20 Jan 2017 20:16:37 -0800 (PST), Frank Krygowski wrote: I did it once, long ago. Actually, I was customizing a hard plastic bodied saddle. I drilled a few holes in the places my sit-bones hit to give it some more flex, and built up cushioning lumps using RTV silicon. Then I stretched and glued a new leather cover over the saddle. IIRC, I used contact cement. It wasn't difficult, and it worked very well. The saddle's still good, although I haven't been using it for quite a while. - Frank Krygowski Do you remember any problem in laying the covering smoothly over the contact cement. -- Cheers, John B. Hi again John. The two great things about not gluing the entire cover to the old saddle are #1 it's a lot easier to stretch the leather and #2 you have lots of time to do that. what I did was glue the leather to one side on the inside of the old saddle shell and let that cure. I do find that cyanoacrylic glue is a lot faster but you don't have the same working time as you do with a good quality contact adhesive/cement. Plus you have to be more careful. With a contact cement you can glue that one side and when cured you can then stretch the new leather (or vinyl) cover over to the oppsite side and mark on the inside of the leather where the contact cement needs to go. Then you apply the contact cememt to the leather and to the inside of the saddle shell and then take your time stretching the leather over the shell. With contact cement you can in need to pull the leather away from the shell if there's a wrinkle and then stretch the leather both side to side and lengthwise to eliminate any wrinkling. I found the thin leather I used could stretch a fair bit in either direction. I also found that if the new leather covering was stretched moderately that it did not wrinkle in use. If concerned about the contact cemented edges coming loose you can then stich the leather to the bottom sides of the saddle shell by drilling small holes through the leather and saddle shell and then stiching the leather to the shell too. Cheers In the article I read the author had used staples to make sure that the edges, folded up under the bottom of the seat and glued, did not come loose, which sounded like a good idea. I had thought that they might be special staples but he mentions buying the short ones needed in a business supply shop. I thought I'd look into that also. -- Cheers, John B. |
#6
|
|||
|
|||
Recovering Saddle
On Saturday, January 21, 2017 at 1:37:49 AM UTC-5, John B. wrote:
On Fri, 20 Jan 2017 21:19:41 -0800 (PST), Sir Ridesalot wrote: On Saturday, January 21, 2017 at 12:01:47 AM UTC-5, John B. wrote: On Fri, 20 Jan 2017 20:16:37 -0800 (PST), Frank Krygowski wrote: I did it once, long ago. Actually, I was customizing a hard plastic bodied saddle. I drilled a few holes in the places my sit-bones hit to give it some more flex, and built up cushioning lumps using RTV silicon. Then I stretched and glued a new leather cover over the saddle. IIRC, I used contact cement. It wasn't difficult, and it worked very well. The saddle's still good, although I haven't been using it for quite a while. - Frank Krygowski Do you remember any problem in laying the covering smoothly over the contact cement. -- Cheers, John B. Hi again John. The two great things about not gluing the entire cover to the old saddle are #1 it's a lot easier to stretch the leather and #2 you have lots of time to do that. what I did was glue the leather to one side on the inside of the old saddle shell and let that cure. I do find that cyanoacrylic glue is a lot faster but you don't have the same working time as you do with a good quality contact adhesive/cement. Plus you have to be more careful. With a contact cement you can glue that one side and when cured you can then stretch the new leather (or vinyl) cover over to the oppsite side and mark on the inside of the leather where the contact cement needs to go. Then you apply the contact cememt to the leather and to the inside of the saddle shell and then take your time stretching the leather over the shell. With contact cement you can in need to pull the leather away from the shell if there's a wrinkle and then stretch the leather both side to side and lengthwise to eliminate any wrinkling. I found the thin leather I used could stretch a fair bit in either direction. I also found that if the new leather covering was stretched moderately that it did not wrinkle in use. If concerned about the contact cemented edges coming loose you can then stich the leather to the bottom sides of the saddle shell by drilling small holes through the leather and saddle shell and then stiching the leather to the shell too. Cheers In the article I read the author had used staples to make sure that the edges, folded up under the bottom of the seat and glued, did not come loose, which sounded like a good idea. I had thought that they might be special staples but he mentions buying the short ones needed in a business supply shop. I thought I'd look into that also. -- Cheers, John B. Staples will work IF #1 they are strong enough to penetrate into the saddle shell and #2 you can getthe stapler to where you need to do the staplind and that can be very hard to do with the saddle rails in place. Good luck and cheers |
#7
|
|||
|
|||
Recovering Saddle
nnnnnnn throw it away
materials have advanced treat urbutt goo.gl/gFsZZw repaired Spec saddles with Shoe Goo UV REC ...this process can go on ideafintely unique in that this is one of the few uses for Shoe Goo but new generation materials saddles are a major improvement in comfort n durability. |
#8
|
|||
|
|||
Recovering Saddle
oh with shoe goo or using contact cement n nylon or polyester place a plastic grocery bag over saddle n tie on with bag handles....is like a chamois flexible interlude.
|
#9
|
|||
|
|||
Recovering Saddle
On Saturday, January 21, 2017 at 9:23:14 AM UTC-5, DATAKOLL MARINE RESEARCH wrote:
oh with shoe goo or using contact cement n nylon or polyester place a plastic grocery bag over saddle n tie on with bag handles....is like a chamois flexible interlude. the shoe goo idea is filler, eg saddle Bondo, on a hard saddle |
#10
|
|||
|
|||
Recovering Saddle
On 1/21/2017 12:01 AM, John B. wrote:
On Fri, 20 Jan 2017 20:16:37 -0800 (PST), Frank Krygowski wrote: I did it once, long ago. Actually, I was customizing a hard plastic bodied saddle. I drilled a few holes in the places my sit-bones hit to give it some more flex, and built up cushioning lumps using RTV silicon. Then I stretched and glued a new leather cover over the saddle. IIRC, I used contact cement. It wasn't difficult, and it worked very well. The saddle's still good, although I haven't been using it for quite a while. - Frank Krygowski Do you remember any problem in laying the covering smoothly over the contact cement. I don't remember any problem, but at this point I can't recall the exact technique I used. The result was/is quite smooth, no wrinkles. -- - Frank Krygowski |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Recovering addict | Don Whybrow | UK | 7 | March 29th 06 06:36 PM |
saddle recovering repair | [email protected] | Techniques | 10 | January 23rd 06 09:14 AM |
recovering seats | [email protected] | Techniques | 7 | July 30th 05 01:51 PM |
recovering a fushionless kh seat? | saam | Unicycling | 5 | July 29th 05 08:01 PM |
Aussie Women recovering | Claudius Vitalis | Racing | 0 | July 25th 05 11:24 PM |