|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
Centuar Ultra-t-shift sstem
On 5/21/2021 11:22 AM, Tom Kunich wrote:
On Friday, May 21, 2021 at 8:13:57 AM UTC-7, wrote: Op vrijdag 21 mei 2021 om 16:30:20 UTC+2 schreef : On Friday, May 21, 2021 at 12:30:32 AM UTC-7, wrote: Op vrijdag 21 mei 2021 om 02:11:05 UTC+2 schreef : I assume that Andrew would be someone that could answer this question, I have a set of the 10 speed Centaur Ultra-shifters. They don't have the same size bolt for locking the shifters onto the handlebars. But the smaller size hex wrench doesn't seem to work. Do these things use something really dumb like a Torx fitting and if so that would require some special tool and where could that be obtained? Its a Torx 25 bolt. Dumb? Torx is a superior interface compared to a hex interface. You better get used to it and buy a set of Torx wrenches. An engineer here at work who uses a allen bolt instead of a Torx in one of their designs get ‘fired’. Lou, I should add that at the spot in the hoods where the Torx wrench is inserted the hoods on the ones I've seen have been cut by the edges of those. That is bad engineering in anyone's book. Huh?? Been there done that: https://photos.app.goo.gl/TypuKvYARvRvvmSg8 Lou, I can't even peel the hood back far enough to SEE the complete bolt as your photo shows. Also you can see that you are inserting the Torx at an angle which is not recommended. There is a channel so that you can insert the Torx from the top side under the hood. This allows the Torx driver to be inserted at a very flat angle. On this we agree. As does the drawing in the Campagnolo user manual. color photo: https://images.immediate.co.uk/produ...size=620%2C412 -- Andrew Muzi www.yellowjersey.org/ Open every day since 1 April, 1971 |
Ads |
#22
|
|||
|
|||
Centuar Ultra-t-shift sstem
AMuzi wrote:
On 5/21/2021 11:00 AM, Tom Kunich wrote: On Friday, May 21, 2021 at 8:06:50 AM UTC-7, AMuzi wrote: On 5/21/2021 9:25 AM, Tom Kunich wrote: On Thursday, May 20, 2021 at 5:23:25 PM UTC-7, AMuzi wrote: On 5/20/2021 7:11 PM, Tom Kunich wrote: I assume that Andrew would be someone that could answer this question, I have a set of the 10 speed Centaur Ultra-shifters. They don't have the same size bolt for locking the shifters onto the handlebars. But the smaller size hex wrench doesn't seem to work. Do these things use something really dumb like a Torx fitting and if so that would require some special tool and where could that be obtained? "Dumb" is sorta subjective, isn't it? Peel back the rubber lever cover from the back side and actually look at it. Because it's an aluminum fastener, it's Torx, not hex. Good engineering/design practice. I think you misunderstand my meaning. At that particular place a Torx is a very bad decision. You have soft pliable rubber hoods and it is not a particularly good idea to stick something down in there with sharp edges. This is engineering 101. Don't destroy what you go to so much trouble and expense to build. I don't get your theory. In practice, any tool slips easily under a rubber cover. For a small aluminum sleeve fastener, Torx is a better drive than Allen or PziDrive or Phillips. The difference in weight from the previous 6 mm bolt and the new Torx 25 is negligible and saying that it is easy ignores the fact that so many new hoods are being sold because the old ones were torn from the torx drivers. If that's true we haven't seen it here. For an aluminum sleeve fastener, Torx is the better design over other drives. Mr Holtman, an engineer, mentioned this fact earlier. Now announcing the new Safe-T-Drive fastener system. Hemispherical drive head mates perfectly with the matching recess in the bolt head, while avoiding scratching nearby surfaces. |
#23
|
|||
|
|||
Centuar Ultra-t-shift sstem
On Fri, 21 May 2021 08:47:14 -0700 (PDT), jbeattie
wrote: You do have to be careful using a cordless driver to install screws, but my driver has five or six torque settings, and the lowest is very low, so I've had no problems with stripping six-bolt disc rotor screws, which, IME, are always Torx head. I get them snug with the driver and then finish them with a torque wrench. Which maker and model driver do you use? I sometimes use a DeWalt DCF787 driver and DCD777 drill/driver for chainsaw work. However, like the bicycle, I don't use either to install screws. The DCD777 drill/driver has an adjustable clutch but the DCF787 driver does NOT have a clutch. I also have a DCD710 drill, which I use for disassembling computers and few other DeWalt power tools. Some details on torque including torque specs for various DeWalt models: https://toolguyd.com/dewalt-cordless-drills-uwo-torque/ My DCD777 will produce 65Nm or 575in-lbs at 500 rpm maximum. No numbers for minimum torque. Apparently, the 15 position clutch is not calibrated. The problem I had with using power tools to install screws came from using them for building computer cases and reassembling chainsaws. The tiny M3 and less tiny 6-32 screws simply don't have enough threads to prevent stripping, especially in thin stamped sheet metal with the usual loose tolerances. The chance of wrecking the computer case was just too much to risk using power. After a few minor disasters assembling computers, chain saws, and bicycles, I decided to use power tools only for disassembly. It might be safe at the lowest clutch settings, but I don't believe that the risk of failure is worth the convenience. Better safe than sorry. I use a corded screw gun to mount plywood panels in my utility trailer using self-tapping Torx head screws, but they use a large bit and are more resistant to stripping. https://static.grainger.com/rp/s/is/...=1000&wid=1000 Nice, but a little big for a bicycle. I've stripped a few bits, usually from driving at an angle. I've tried hardening some bits, which helps. "Experiment CRASH TEST hardening bit for screwdriver" https://www.youtube.com/watch?v=Y7RSfVqbjSo (3:00) Misc: T25 is for decking screws and T27 for most chainsaws. -- Jeff Liebermann PO Box 272 http://www.LearnByDestroying.com Ben Lomond CA 95005-0272 Skype: JeffLiebermann AE6KS 831-336-2558 |
#24
|
|||
|
|||
Centuar Ultra-t-shift sstem
On Friday, May 21, 2021 at 7:17:13 PM UTC-7, wrote:
On Fri, 21 May 2021 08:47:14 -0700 (PDT), jbeattie wrote: You do have to be careful using a cordless driver to install screws, but my driver has five or six torque settings, and the lowest is very low, so I've had no problems with stripping six-bolt disc rotor screws, which, IME, are always Torx head. I get them snug with the driver and then finish them with a torque wrench. Which maker and model driver do you use? I sometimes use a DeWalt DCF787 driver and DCD777 drill/driver for chainsaw work. However, like the bicycle, I don't use either to install screws. The DCD777 drill/driver has an adjustable clutch but the DCF787 driver does NOT have a clutch. I also have a DCD710 drill, which I use for disassembling computers and few other DeWalt power tools. Some details on torque including torque specs for various DeWalt models: https://toolguyd.com/dewalt-cordless-drills-uwo-torque/ My DCD777 will produce 65Nm or 575in-lbs at 500 rpm maximum. No numbers for minimum torque. Apparently, the 15 position clutch is not calibrated. My ancient Makita died, and I got an el cheapo Black and Decker replacement at Home Depo. https://tinyurl.com/25as2rk It has 11 clutch settings. It's a surprisingly god drill for the price. I also have some macho corded drills including a Milwaukee hammer drill. I'm just throwing that out there to establish my tool bonafides. I only use a drill on two bicycle fittings -- spoke nipples and six-bolt rotor bolts. I also use it for the bolts on my gas pole hedge trimmer (Husky) since there are so many M5 bolts, and removing them with a wrench takes forever. I've driven lots of other types of screws -- including the self-tapping Torx heads I linked, deck screws, drywall, cement board, etc., etc. It is easy to strip all of those with the corded screw gun, and you have to be light on the trigger. -- Jay Beattie. |
#25
|
|||
|
|||
Centuar Ultra-t-shift sstem
On Fri, 21 May 2021 19:17:06 -0700, Jeff Liebermann
wrote: On Fri, 21 May 2021 08:47:14 -0700 (PDT), jbeattie wrote: You do have to be careful using a cordless driver to install screws, but my driver has five or six torque settings, and the lowest is very low, so I've had no problems with stripping six-bolt disc rotor screws, which, IME, are always Torx head. I get them snug with the driver and then finish them with a torque wrench. Which maker and model driver do you use? I sometimes use a DeWalt DCF787 driver and DCD777 drill/driver for chainsaw work. However, like the bicycle, I don't use either to install screws. The DCD777 drill/driver has an adjustable clutch but the DCF787 driver does NOT have a clutch. I also have a DCD710 drill, which I use for disassembling computers and few other DeWalt power tools. Some details on torque including torque specs for various DeWalt models: https://toolguyd.com/dewalt-cordless-drills-uwo-torque/ My DCD777 will produce 65Nm or 575in-lbs at 500 rpm maximum. No numbers for minimum torque. Apparently, the 15 position clutch is not calibrated. The problem I had with using power tools to install screws came from using them for building computer cases and reassembling chainsaws. The tiny M3 and less tiny 6-32 screws simply don't have enough threads to prevent stripping, especially in thin stamped sheet metal with the usual loose tolerances. The chance of wrecking the computer case was just too much to risk using power. After a few minor disasters assembling computers, chain saws, and bicycles, I decided to use power tools only for disassembly. It might be safe at the lowest clutch settings, but I don't believe that the risk of failure is worth the convenience. Better safe than sorry. I use a corded screw gun to mount plywood panels in my utility trailer using self-tapping Torx head screws, but they use a large bit and are more resistant to stripping. https://static.grainger.com/rp/s/is/...=1000&wid=1000 Nice, but a little big for a bicycle. I've stripped a few bits, usually from driving at an angle. I've tried hardening some bits, which helps. "Experiment CRASH TEST hardening bit for screwdriver" https://www.youtube.com/watch?v=Y7RSfVqbjSo (3:00) Quite simply that guy doesn't know what he is doing, at least as shown in the film. The quenching in carbon is probably a rather futile attempt at case hardening and had he submerged the bit in carbon dust and then heated the whole mess to a red heat and held it there for a period and then quenched the bit he would have had far more success. As for his quenching in liquids he doesn't seem to get the bit anywhere near hardening temperature, i.e. red heat. Misc: T25 is for decking screws and T27 for most chainsaws. -- Cheers, John B. |
#26
|
|||
|
|||
Centuar Ultra-t-shift sstem
On Sat, 22 May 2021 10:56:25 +0700, John B.
wrote: On Fri, 21 May 2021 19:17:06 -0700, Jeff Liebermann wrote: Nice, but a little big for a bicycle. I've stripped a few bits, usually from driving at an angle. I've tried hardening some bits, which helps. "Experiment CRASH TEST hardening bit for screwdriver" https://www.youtube.com/watch?v=Y7RSfVqbjSo (3:00) Quite simply that guy doesn't know what he is doing, at least as shown in the film. The quenching in carbon is probably a rather futile attempt at case hardening and had he submerged the bit in carbon dust and then heated the whole mess to a red heat and held it there for a period and then quenched the bit he would have had far more success. As for his quenching in liquids he doesn't seem to get the bit anywhere near hardening temperature, i.e. red heat. He doesn't get it quite right, but I like the method and the result. However, as you note, he made many mistakes. Quenching in clean oil doesn't work. Quenching in used motor oil does work because it contains free carbon which will dissolve into the steel bit. However, controlling the amount of carbon absorbed is difficult. One could easily end up with too much carbon and produce brittle cast iron. There's also a tendency for the surface to oxidize. That can all be fixed by switching to vacuum hardening, but that might be overkill for hardening a bit. Quenching in carbon dust doesn't work because there is no oil or water to conduct the heat to the loose carbon and to prevent oxidation. In his setup, the carbon acts like a thermal insulator with about 1/10th the thermal conductivity of steel. Quenching in water results in a hard but brittle bit. However, he didn't bother annealing the hardened bit, which would probably have resulted in a much better tip. Hardening by slow air cooling is a good compromise between the original untreated bit, and the various attempts to harden the tip. However, air cooling only works with steel compositions that are made for air hardening such as those with high chromium content: https://en.wikipedia.org/wiki/Tool_steel#Air-hardening:_the_A_series The problem here is that I don't know what flavor of mystery metal was used to make the original bit. The bit does NOT have a high chromium content because all the bits were magnetic. I've only hardened about 10 Phillips #2 bits. Everything was an experiment and no two were hardened in the same manner. I did reproduce the cracking of the water quenched bit, but later produced something quite hard by re-heating and annealing the water quenched bit in dirty motor oil. Quenching in dirty motor oil without annealing resulted in something only slightly better than the water hardening and air annealing method. -- Jeff Liebermann PO Box 272 http://www.LearnByDestroying.com Ben Lomond CA 95005-0272 Skype: JeffLiebermann AE6KS 831-336-2558 |
#27
|
|||
|
|||
Centuar Ultra-t-shift sstem
On Fri, 21 May 2021 23:06:02 -0700, Jeff Liebermann
wrote: On Sat, 22 May 2021 10:56:25 +0700, John B. wrote: On Fri, 21 May 2021 19:17:06 -0700, Jeff Liebermann wrote: Nice, but a little big for a bicycle. I've stripped a few bits, usually from driving at an angle. I've tried hardening some bits, which helps. "Experiment CRASH TEST hardening bit for screwdriver" https://www.youtube.com/watch?v=Y7RSfVqbjSo (3:00) Quite simply that guy doesn't know what he is doing, at least as shown in the film. The quenching in carbon is probably a rather futile attempt at case hardening and had he submerged the bit in carbon dust and then heated the whole mess to a red heat and held it there for a period and then quenched the bit he would have had far more success. As for his quenching in liquids he doesn't seem to get the bit anywhere near hardening temperature, i.e. red heat. He doesn't get it quite right, but I like the method and the result. However, as you note, he made many mistakes. Quenching in clean oil doesn't work. Quenching in used motor oil does work because it contains free carbon which will dissolve into the steel bit. However, controlling the amount of carbon absorbed is difficult. One could easily end up with too much carbon and produce brittle cast iron. There's also a tendency for the surface to oxidize. That can all be fixed by switching to vacuum hardening, but that might be overkill for hardening a bit. Quenching in carbon dust doesn't work because there is no oil or water to conduct the heat to the loose carbon and to prevent oxidation. In his setup, the carbon acts like a thermal insulator with about 1/10th the thermal conductivity of steel. Quenching in water results in a hard but brittle bit. However, he didn't bother annealing the hardened bit, which would probably have resulted in a much better tip. Hardening by slow air cooling is a good compromise between the original untreated bit, and the various attempts to harden the tip. However, air cooling only works with steel compositions that are made for air hardening such as those with high chromium content: https://en.wikipedia.org/wiki/Tool_steel#Air-hardening:_the_A_series The problem here is that I don't know what flavor of mystery metal was used to make the original bit. The bit does NOT have a high chromium content because all the bits were magnetic. I've only hardened about 10 Phillips #2 bits. Everything was an experiment and no two were hardened in the same manner. I did reproduce the cracking of the water quenched bit, but later produced something quite hard by re-heating and annealing the water quenched bit in dirty motor oil. Quenching in dirty motor oil without annealing resulted in something only slightly better than the water hardening and air annealing method. The problem with the video is that you don't know what he is starting with. Normal practice when hardening a steel object is to fully harden it, i.e., heat to a red temperature and quench, normally in water or even salt water. this results in the maximum hardness, and brittleness, for that alloy. Then reheat (temper) to a lower temperature which reduces the hardness by (hopefully) an amount that leaves one (again hopefully) with a device of sufficient hardness to do whatever work is required but not as brittle as the fully hardened condition and then a final quench to stop all further changes. I might add that the higher the carbon content the harder the first quench will leave the work and with the greatest internal stresses. I have quenched a number of high carbon "drill rod" tools in water and had several of them crack after quenching while laying on the bench while waiting for the temperature of the oven to come down to a "tempering" temperature. The "secret" is in the speed of hardening and water provides the fastest cooling and oils are somewhat slower cooling with light grades of oil being faster then heavier grades. If you heat iron or steel in the presence of carbon the material will absorb some of the carbon and you will "case harden", the item forming a thin skin of high carbon over a low carbon core. If you then heat the material and quench it you will end up with a thin skin of hard and thus more brittle steel over a softer and less brittle core. A blacksmith will temper by colors. First heat the item and fully harden it and then, after polishing or otherwise removing any surface oxidation, then reheat to a specific color and quench again for the harness you require. Light colors, yellow or very light brown result in a harder material then darker colors, light blue, dark blue, etc. -- Cheers, John B. |
#28
|
|||
|
|||
Centuar Ultra-t-shift sstem
On 5/22/2021 1:06 AM, Jeff Liebermann wrote:
On Sat, 22 May 2021 10:56:25 +0700, John B. wrote: On Fri, 21 May 2021 19:17:06 -0700, Jeff Liebermann wrote: Nice, but a little big for a bicycle. I've stripped a few bits, usually from driving at an angle. I've tried hardening some bits, which helps. "Experiment CRASH TEST hardening bit for screwdriver" https://www.youtube.com/watch?v=Y7RSfVqbjSo (3:00) Quite simply that guy doesn't know what he is doing, at least as shown in the film. The quenching in carbon is probably a rather futile attempt at case hardening and had he submerged the bit in carbon dust and then heated the whole mess to a red heat and held it there for a period and then quenched the bit he would have had far more success. As for his quenching in liquids he doesn't seem to get the bit anywhere near hardening temperature, i.e. red heat. He doesn't get it quite right, but I like the method and the result. However, as you note, he made many mistakes. Quenching in clean oil doesn't work. Quenching in used motor oil does work because it contains free carbon which will dissolve into the steel bit. However, controlling the amount of carbon absorbed is difficult. One could easily end up with too much carbon and produce brittle cast iron. There's also a tendency for the surface to oxidize. That can all be fixed by switching to vacuum hardening, but that might be overkill for hardening a bit. Quenching in carbon dust doesn't work because there is no oil or water to conduct the heat to the loose carbon and to prevent oxidation. In his setup, the carbon acts like a thermal insulator with about 1/10th the thermal conductivity of steel. Quenching in water results in a hard but brittle bit. However, he didn't bother annealing the hardened bit, which would probably have resulted in a much better tip. Hardening by slow air cooling is a good compromise between the original untreated bit, and the various attempts to harden the tip. However, air cooling only works with steel compositions that are made for air hardening such as those with high chromium content: https://en.wikipedia.org/wiki/Tool_steel#Air-hardening:_the_A_series The problem here is that I don't know what flavor of mystery metal was used to make the original bit. The bit does NOT have a high chromium content because all the bits were magnetic. I've only hardened about 10 Phillips #2 bits. Everything was an experiment and no two were hardened in the same manner. I did reproduce the cracking of the water quenched bit, but later produced something quite hard by re-heating and annealing the water quenched bit in dirty motor oil. Quenching in dirty motor oil without annealing resulted in something only slightly better than the water hardening and air annealing method. Small edged 1020 pieces can be case hardened with acetylene soot which was once a standard lesson in machine shop classes. I don't think this has any practical application for a Phillips bit since new ones are dirt cheap. Comments here note that bicycle sprockets are very cheap compared t making a sprocket: https://hackaday.com/2019/11/29/maki...-the-tidy-way/ -- Andrew Muzi www.yellowjersey.org/ Open every day since 1 April, 1971 |
#29
|
|||
|
|||
Centuar Ultra-t-shift sstem
On Friday, May 21, 2021 at 8:00:45 PM UTC-7, jbeattie wrote:
On Friday, May 21, 2021 at 7:17:13 PM UTC-7, wrote: On Fri, 21 May 2021 08:47:14 -0700 (PDT), jbeattie wrote: You do have to be careful using a cordless driver to install screws, but my driver has five or six torque settings, and the lowest is very low, so I've had no problems with stripping six-bolt disc rotor screws, which, IME, are always Torx head. I get them snug with the driver and then finish them with a torque wrench. Which maker and model driver do you use? I sometimes use a DeWalt DCF787 driver and DCD777 drill/driver for chainsaw work. However, like the bicycle, I don't use either to install screws. The DCD777 drill/driver has an adjustable clutch but the DCF787 driver does NOT have a clutch. I also have a DCD710 drill, which I use for disassembling computers and few other DeWalt power tools. Some details on torque including torque specs for various DeWalt models: https://toolguyd.com/dewalt-cordless-drills-uwo-torque/ My DCD777 will produce 65Nm or 575in-lbs at 500 rpm maximum. No numbers for minimum torque. Apparently, the 15 position clutch is not calibrated. My ancient Makita died, and I got an el cheapo Black and Decker replacement at Home Depo. https://tinyurl.com/25as2rk It has 11 clutch settings. It's a surprisingly god drill for the price. I also have some macho corded drills including a Milwaukee hammer drill. I'm just throwing that out there to establish my tool bonafides. I only use a drill on two bicycle fittings -- spoke nipples and six-bolt rotor bolts. I also use it for the bolts on my gas pole hedge trimmer (Husky) since there are so many M5 bolts, and removing them with a wrench takes forever. I've driven lots of other types of screws -- including the self-tapping Torx heads I linked, deck screws, drywall, cement board, etc., etc. It is easy to strip all of those with the corded screw gun, and you have to be light on the trigger. We had Frank gaffawing that torque wrenches were around forever. What he doesn't seem to know was that they were NOT used to limit how tight you make a bolt as much as to make sure things were evenly tightened. This prevented things like head gaskets leaking and the like. It wasn't until softer materials like Aluminum came into use that rather to make sure things were all tightened equally they were used to prevent overtightening and stripping softer materials. |
#30
|
|||
|
|||
Centuar Ultra-t-shift sstem
On 5/22/2021 2:06 AM, Jeff Liebermann wrote:
On Sat, 22 May 2021 10:56:25 +0700, John B. wrote: On Fri, 21 May 2021 19:17:06 -0700, Jeff Liebermann wrote: Nice, but a little big for a bicycle. I've stripped a few bits, usually from driving at an angle. I've tried hardening some bits, which helps. "Experiment CRASH TEST hardening bit for screwdriver" https://www.youtube.com/watch?v=Y7RSfVqbjSo (3:00) Quite simply that guy doesn't know what he is doing, at least as shown in the film. The quenching in carbon is probably a rather futile attempt at case hardening and had he submerged the bit in carbon dust and then heated the whole mess to a red heat and held it there for a period and then quenched the bit he would have had far more success. As for his quenching in liquids he doesn't seem to get the bit anywhere near hardening temperature, i.e. red heat. +1 He doesn't get it quite right, but I like the method and the result. However, as you note, he made many mistakes. Quenching in clean oil doesn't work. Quenching in used motor oil does work because it contains free carbon which will dissolve into the steel bit. No, sorry. There's no migration of carbon into the hot steel during an oil quench, dirty or no. A lot of backyard mechanics don't understand oil quenching. They think it's always magically superior to water quenching. But the purpose of an oil quench is to give a slower quench than water. (Brine gives a faster quench.) In a properly controlled industrial process, the choice of quench rate is determined by the type of steel alloy. Some alloys have the ability to fully harden with a slower quench. Those use oil quenching. The big benefit is that a slower quench is less likely to warp or crack the part. This can be important for parts with complex geometry, varying wall thicknesses etc. However, controlling the amount of carbon absorbed is difficult. One could easily end up with too much carbon and produce brittle cast iron. The diffusion of carbon into steel is called carburizing, and it's a solid solution phenomenon. Solid carbon atoms _slowly_ make their way in among the solid iron (or steel) atoms. It's a lot different from water soaking into a sponge. It takes a long time. Hardening by slow air cooling is a good compromise between the original untreated bit, and the various attempts to harden the tip. However, air cooling only works with steel compositions that are made for air hardening such as those with high chromium content: https://en.wikipedia.org/wiki/Tool_steel#Air-hardening:_the_A_series Yes. Air quenching is much slower than oil quenching, given similar cross sections. It usually requires even fancier steel alloys. BTW, I remember visiting a wire drawing factory producing steel wire for radial tire belts. Occasionally the drawing process would cause a wire to break. They had a rig that electrically butt-welded the broken ends of the wire. But the thin wire air quenched to brittle martensite, so the rig re-warmed it to temper it or anneal it. It was like this demonstration of welding a band saw blade, but completely automatic: https://www.youtube.com/watch?v=xuFpZTUjtmg -- - Frank Krygowski |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Performance Ultra Shorts or Ultra Bib Shorts-opinions | JBIthaca | Techniques | 40 | March 8th 06 02:34 PM |
STI shift levers won't shift down | donb | Techniques | 3 | April 20th 05 07:21 PM |
Shift lever loose on rear derailleur shift | Larry Gagnon | Techniques | 3 | April 5th 05 05:42 PM |
WTB:Looking for a Daytona/Centuar/Athena or Veloce 9sp rear hub to build a spare wheel. | Jeff & Jane | Marketplace | 0 | May 4th 04 03:38 AM |
Profile Design "swift shift" and shift adapter | David Kerber | Techniques | 6 | November 17th 03 09:37 PM |