|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
To Lube Or Not To Lube Shifter Cables That is the Question!
Steve Sr. wrote: Bike Gurus, My apologies to Shakespeare. I was wondering if there was any consensus on this subject. I am referring to the Shimano type of cables with the plastic core. If the answer is yes, then what is the recommended lube? I can tell you one lube not to use is Finish Line "dry". It sets up way too stiff and will definitely cause shifting issues. I am currently working on an Ultegra 10 system that is shifting kind of funky. I recently had it in to the bike shop and I think they lubed the cables but I don't know with what. Yes, I have already checked for Gatorade under the bottom bracket and there wasn't any. Thanks, Steve I use White Lightning (on IRD for Campy brake and shift cables) and I only use it when they are first installed. Your lube should work too if you do the same. Lube the cable and then wipe it down after the wet medium is dried. Wet lubes attract dust and will only make it worse in a short period. Most cables should work without lube so the dry lube is optional. With both sets of cables (w Campy) wrapped under the bar tape, it seems logical that any advantage can help when they have to go through some of those tight angles caused by following the bar. I guess I just have my habits to make my gear operate the best that I can. Dry lube is great for those circumstances when you need to avoid attracting grime and they work best if wiped before putting the effected components in place if there is any risk that the dried lube will cause problems like you pointed out. I use the same dry lube on cleats (Speedplay) and brake calipers. It makes such a huge difference in avoiding grime while allowing nearly the same performance as they would if freshly hit with WD40 or similar. I also use it on my drivetrain during the wet months becuase it lasts so much longer than wet lubes when exposed to water (its second key advantage). |
Ads |
#2
|
|||
|
|||
To Lube Or Not To Lube Shifter Cables That is the Question!
Chris M wrote:
Steve Sr. wrote: Bike Gurus, My apologies to Shakespeare. I was wondering if there was any consensus on this subject. I am referring to the Shimano type of cables with the plastic core. If the answer is yes, then what is the recommended lube? I can tell you one lube not to use is Finish Line "dry". It sets up way too stiff and will definitely cause shifting issues. I am currently working on an Ultegra 10 system that is shifting kind of funky. I recently had it in to the bike shop and I think they lubed the cables but I don't know with what. Yes, I have already checked for Gatorade under the bottom bracket and there wasn't any. Thanks, Steve I use White Lightning (on IRD for Campy brake and shift cables) and I only use it when they are first installed. Your lube should work too if you do the same. Lube the cable and then wipe it down after the wet medium is dried. Wet lubes attract dust and will only make it worse in a short period. To the contrary, I cut and run the cables dry, and when they invariably get gummy after a few months, I use Prolink dabbed in a rag and wiped directly on the cable, not dribbled down into the housing. Most cables should work without lube so the dry lube is optional. With both sets of cables (w Campy) wrapped under the bar tape, it seems logical that any advantage can help when they have to go through some of those tight angles caused by following the bar. I guess I just have my habits to make my gear operate the best that I can. Dry lube is great for those circumstances when you need to avoid attracting grime and they work best if wiped before putting the effected components in place if there is any risk that the dried lube will cause problems like you pointed out. I use the same dry lube on cleats (Speedplay) and brake calipers. It makes such a huge difference in avoiding grime while allowing nearly the same performance as they would if freshly hit with WD40 or similar. I also use it on my drivetrain during the wet months becuase it lasts so much longer than wet lubes when exposed to water (its second key advantage). Many find the opposite to be true. -- Phil |
#3
|
|||
|
|||
To Lube Or Not To Lube Shifter Cables That is the Question!
I pull the cable across a block of wax a few times (or soak it in the
molten wax if I'm doing a chain at the time) before inserting it into the noodle(s). This not only adss lubrication, but it also leaves a solid water resistant coating on the exposed sections. - - Comments and opinions compliments of, "Your Friendly Neighborhood Wheelman" My web Site: http "colon-slash-slash" geocities "dot" com "slash" czcorner To E-mail me: ChrisZCorner "at" webtv "dot" net |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Shifter question. | NewRoadie | Racing | 7 | September 10th 04 09:34 PM |
Lube question about Record hubs | Mark | Techniques | 21 | August 24th 04 11:58 PM |
To lube new brake/gear cables? | JackGuest-com | UK | 5 | June 10th 04 08:13 PM |
Avid Flak jacket shifter cables/ cable stop question | qa2 | Mountain Biking | 1 | January 27th 04 09:53 AM |
Question for the anti-helmet guys | Harris | Techniques | 37 | October 7th 03 04:40 PM |