|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Dropout blues - rear wheel pulling out
Gday,
I have an older italian steel frame which I just got second hand and manage to keep pulling the rear wheel out of the dropouts. The dropouts are almost parallel to the chain line which probably doesn't help. Anyway, I read thru previous posts and the comments seem to be distilled to 1. ensure the axle isn't protruding thru the dropouts preventing QR binding properly 2. use a steel nutted QR such as shimano as they bind better than the non steel alloy ones. 3. insert a binding washer ( a serrated washer ) between frame and dropouts 4. score the dropouts as a means of last resort 5. use track axle/nuts I have some questions regarding these and a couple of other things. 1. I have mavic cosmic elite hubs/wheelset. My LBS reckons they're "good wheels which are designed to handle the QR being jacked up as tight as you can get it". I read elsewhere that overtightening QR's can cause compression of the bearings and other equally painful sounding ailments. Any solution will require me jacking the QR up very tight so the q is will I be damaging my hub in the process? 2. do track axles/nuts actually hold the wheel in place any better than a quick release? I so, will this put extra pressure on my hub ala question 1? 3. if i wanted to score the dropouts (eek) how should this be done? 4. will inserting the washers change the rear spacing and affect shifting? If so can i adjust for this simply by adjusting the DR limit screws or is it more complex than that? 5. is the wise options just to kiss my ( ideal barring the wheel falling off thing) frame goodbye, and look for a different less life threatening one? Appreciate any thoughts you might have. Happy flaming, Will |
Ads |
#2
|
|||
|
|||
Dropout blues - rear wheel pulling out
1. I have mavic cosmic elite hubs/wheelset. My LBS reckons they're
"good wheels which are designed to handle the QR being jacked up as tight as you can get it". I read elsewhere that overtightening QR's can cause compression of the bearings and other equally painful sounding ailments. Any solution will require me jacking the QR up very tight so the q is will I be damaging my hub in the process? Will: I'm not a big fan of the Mavic QRs; my guess is that you'll find better results if you replace the rear one with a conventional Shimano (or Campy) style. The problem isn't just the mating surfaces being steel vs aluminum or serrated vs smooth, but the way the mechanism works. Give it a try before pulling hair out on all the other options. --Mike-- Chain Reaction Bicycles www.ChainReactionBicycles.com "SuperFly" wrote in message oups.com... Gday, I have an older italian steel frame which I just got second hand and manage to keep pulling the rear wheel out of the dropouts. The dropouts are almost parallel to the chain line which probably doesn't help. Anyway, I read thru previous posts and the comments seem to be distilled to 1. ensure the axle isn't protruding thru the dropouts preventing QR binding properly 2. use a steel nutted QR such as shimano as they bind better than the non steel alloy ones. 3. insert a binding washer ( a serrated washer ) between frame and dropouts 4. score the dropouts as a means of last resort 5. use track axle/nuts I have some questions regarding these and a couple of other things. 1. I have mavic cosmic elite hubs/wheelset. My LBS reckons they're "good wheels which are designed to handle the QR being jacked up as tight as you can get it". I read elsewhere that overtightening QR's can cause compression of the bearings and other equally painful sounding ailments. Any solution will require me jacking the QR up very tight so the q is will I be damaging my hub in the process? 2. do track axles/nuts actually hold the wheel in place any better than a quick release? I so, will this put extra pressure on my hub ala question 1? 3. if i wanted to score the dropouts (eek) how should this be done? 4. will inserting the washers change the rear spacing and affect shifting? If so can i adjust for this simply by adjusting the DR limit screws or is it more complex than that? 5. is the wise options just to kiss my ( ideal barring the wheel falling off thing) frame goodbye, and look for a different less life threatening one? Appreciate any thoughts you might have. Happy flaming, Will |
#3
|
|||
|
|||
Dropout blues - rear wheel pulling out
SuperFly wrote:
Gday, I have an older italian steel frame which I just got second hand and manage to keep pulling the rear wheel out of the dropouts. use campy or shimano closed cam skewers. much better mechanism allowing higher, more consistent application of clamping force. they don't allow slip. The dropouts are almost parallel to the chain line which probably doesn't help. Anyway, I read thru previous posts and the comments seem to be distilled to 1. ensure the axle isn't protruding thru the dropouts preventing QR binding properly 2. use a steel nutted QR such as shimano as they bind better than the non steel alloy ones. 3. insert a binding washer ( a serrated washer ) between frame and dropouts 4. score the dropouts as a means of last resort 5. use track axle/nuts I have some questions regarding these and a couple of other things. 1. I have mavic cosmic elite hubs/wheelset. My LBS reckons they're "good wheels which are designed to handle the QR being jacked up as tight as you can get it". I read elsewhere that overtightening QR's can cause compression of the bearings and other equally painful sounding ailments. Any solution will require me jacking the QR up very tight so the q is will I be damaging my hub in the process? 2. do track axles/nuts actually hold the wheel in place any better than a quick release? I so, will this put extra pressure on my hub ala question 1? 3. if i wanted to score the dropouts (eek) how should this be done? 4. will inserting the washers change the rear spacing and affect shifting? If so can i adjust for this simply by adjusting the DR limit screws or is it more complex than that? 5. is the wise options just to kiss my ( ideal barring the wheel falling off thing) frame goodbye, and look for a different less life threatening one? Appreciate any thoughts you might have. Happy flaming, Will |
#4
|
|||
|
|||
Dropout blues - rear wheel pulling out
"SuperFly" wrote in message oups.com... Gday, I have an older italian steel frame which I just got second hand and manage to keep pulling the rear wheel out of the dropouts. The dropouts are almost parallel to the chain line which probably doesn't help. Anyway, I read thru previous posts and the comments seem to be distilled to 1. ensure the axle isn't protruding thru the dropouts preventing QR binding properly 2. use a steel nutted QR such as shimano as they bind better than the non steel alloy ones. 3. insert a binding washer ( a serrated washer ) between frame and dropouts 4. score the dropouts as a means of last resort 5. use track axle/nuts I have some questions regarding these and a couple of other things. 1. I have mavic cosmic elite hubs/wheelset. My LBS reckons they're "good wheels which are designed to handle the QR being jacked up as tight as you can get it". I read elsewhere that overtightening QR's can cause compression of the bearings and other equally painful sounding ailments. Any solution will require me jacking the QR up very tight so the q is will I be damaging my hub in the process? 2. do track axles/nuts actually hold the wheel in place any better than a quick release? I so, will this put extra pressure on my hub ala question 1? 3. if i wanted to score the dropouts (eek) how should this be done? 4. will inserting the washers change the rear spacing and affect shifting? If so can i adjust for this simply by adjusting the DR limit screws or is it more complex than that? 5. is the wise options just to kiss my ( ideal barring the wheel falling off thing) frame goodbye, and look for a different less life threatening one? Appreciate any thoughts you might have. Happy flaming, Will I had the same problem when I upgraded the wheels and other components on my 1978 Gios. The newer quick releases don't work on horizontal dropouts. I reinstalled my Campy skewers and that solved the problem immediately. Neal |
#5
|
|||
|
|||
Dropout blues - rear wheel pulling out
SuperFly wrote:
Gday, I have an older italian steel frame which I just got second hand and manage to keep pulling the rear wheel out of the dropouts. The dropouts are almost parallel to the chain line which probably doesn't help. Anyway, I read thru previous posts and the comments seem to be distilled to 1. ensure the axle isn't protruding thru the dropouts preventing QR binding properly 2. use a steel nutted QR such as shimano as they bind better than the non steel alloy ones. 3. insert a binding washer ( a serrated washer ) between frame and dropouts 4. score the dropouts as a means of last resort 5. use track axle/nuts I have some questions regarding these and a couple of other things. 1. I have mavic cosmic elite hubs/wheelset. My LBS reckons they're "good wheels which are designed to handle the QR being jacked up as tight as you can get it". I read elsewhere that overtightening QR's can cause compression of the bearings and other equally painful sounding ailments. Any solution will require me jacking the QR up very tight so the q is will I be damaging my hub in the process? 2. do track axles/nuts actually hold the wheel in place any better than a quick release? I so, will this put extra pressure on my hub ala question 1? 3. if i wanted to score the dropouts (eek) how should this be done? 4. will inserting the washers change the rear spacing and affect shifting? If so can i adjust for this simply by adjusting the DR limit screws or is it more complex than that? 5. is the wise options just to kiss my ( ideal barring the wheel falling off thing) frame goodbye, and look for a different less life threatening one? Use an old steel-handled Shimano skewer and ensure the cam is lubricated with a drop of oil. |
#6
|
|||
|
|||
Dropout blues - rear wheel pulling out
|
#7
|
|||
|
|||
Dropout blues - rear wheel pulling out
SuperFly wrote:
The dropouts are almost parallel to the chain line which probably doesn't help. Bike shops have tools to check the dropout alignment and to adjust it by cold setting (that is, bending). I'd make sure the dropout alignment is correct (that is, their faces parallel to the central plane of the frame). Tom Ace |
#8
|
|||
|
|||
Dropout blues - rear wheel pulling out
Adjusting the bearings and then tightening the **** out of the
quick-release is definitely the best solution. I have a steel-framed singlespeed that didn't have good bite with the locknut serrations. It took me a decent crash when my chain derailed to figure that one out. I use a old-school steel-handled Shimano QR and I have to yank on it pretty hard to get it off. Whatever you do, don't use any of the small late-model Specialized skewers. They're crap. Phil |
#9
|
|||
|
|||
Dropout blues - rear wheel pulling out
SuperFly wrote:
Gday, I have an older italian steel frame which I just got second hand and manage to keep pulling the rear wheel out of the dropouts. The dropouts are almost parallel to the chain line which probably doesn't help. Anyway, I read thru previous posts and the comments seem to be distilled to 1. ensure the axle isn't protruding thru the dropouts preventing QR binding properly 2. use a steel nutted QR such as shimano as they bind better than the non steel alloy ones. 3. insert a binding washer ( a serrated washer ) between frame and dropouts 4. score the dropouts as a means of last resort 5. use track axle/nuts I have some questions regarding these and a couple of other things. 1. I have mavic cosmic elite hubs/wheelset. My LBS reckons they're "good wheels which are designed to handle the QR being jacked up as tight as you can get it". I read elsewhere that overtightening QR's can cause compression of the bearings and other equally painful sounding ailments. Any solution will require me jacking the QR up very tight so the q is will I be damaging my hub in the process? 2. do track axles/nuts actually hold the wheel in place any better than a quick release? I so, will this put extra pressure on my hub ala question 1? 3. if i wanted to score the dropouts (eek) how should this be done? 4. will inserting the washers change the rear spacing and affect shifting? If so can i adjust for this simply by adjusting the DR limit screws or is it more complex than that? 5. is the wise options just to kiss my ( ideal barring the wheel falling off thing) frame goodbye, and look for a different less life threatening one? Appreciate any thoughts you might have. Happy flaming, Will http://www.sheldonbrown.com/skewers.html |
#10
|
|||
|
|||
Dropout blues - rear wheel pulling out
In article .com,
"SuperFly" wrote: Gday, I have an older italian steel frame which I just got second hand and manage to keep pulling the rear wheel out of the dropouts. The dropouts are almost parallel to the chain line which probably doesn't help. Try a drop of oil on the cam of the quick release. It can bind and prevent proper tightening of the QR. (Concerning other question: Adjust bearings a bit loose, such that tightening the QR compresses the axle enough to take up the play and give a very modest pre-load.) -- Ned Mantei Zurich, Switzerland |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New bicycle idea | Bob Marley | General | 49 | October 7th 04 05:20 AM |
For Trade: 700c Spin Rear Wheel in Boulder for normal spoked wheel | Joe | Marketplace | 0 | September 27th 04 12:38 AM |
Ritchey Zero system rear wheel | cliff | Techniques | 3 | June 3rd 04 09:48 PM |
Wheelbuilding issues | Nate Knutson | Techniques | 13 | May 9th 04 03:29 PM |
New 700c Rear Wheel (for Tour Easy) | Jon Meinecke | Recumbent Biking | 5 | September 27th 03 12:40 AM |