A Cycling & bikes forum. CycleBanter.com

Go Back   Home » CycleBanter.com forum » rec.bicycles » Techniques
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Reasonable expectation...............



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #9  
Old September 16th 17, 09:30 PM posted to rec.bicycles.tech
[email protected]
external usenet poster
 
Posts: 3,345
Default Reasonable expectation...............

On Friday, September 15, 2017 at 7:30:42 PM UTC-7, John B. wrote:
On Fri, 15 Sep 2017 19:59:27 +0100, "Ian Field"
wrote:



"John B." wrote in message
.. .
On Thu, 14 Sep 2017 21:33:17 +0100, "Ian Field"
wrote:



"Joerg" wrote in message
...
On 2017-09-14 10:42, AMuzi wrote:
On 9/14/2017 12:32 PM, Ian Field wrote:
The bike I built up on a frame I dragged out of a hedge has
a seized seat post.

So far; I've slackened the clamp bolt and give it a squirt
of PTFE penetrating oil at least once a day - is there a
reasonable expectation that it might work loose?

Thanks.

Yes.
The vibration and cyclic loading of the post can free them.
Not always but well worth a daily shot of penetrant and some miles.
Leave the bolt out and cross your fingers!


Might sing soprano after it let go all of a sudden :-)

Its seriously stuck, it'll probably need a lot of twisting to shift it at
all once it starts to loosen.

If I still had a welder, I'd weld a lever arm to it so I could apply
enough
force.

If it is an aluminum seat post in a steel frame and you can't budge it
with a, oh say 24 inch pipe wrench, after a few days of penetrating
oil then it probably won't come out without some serious attention.

I once spent nearly a week to make a boring bar and boring out a stuck
seat tube after all else failed however after reading the Internet I
discovered that dissolving the aluminum tube using lye would have been
much easier :-)


No aluminium - and I wouldn't want a glob of corrosive **** running down
into the BB bracket if there was.


You are supposed to disassemble the bicycle before you start :-(

From the Internet:

As a strong alkali, sodium hydroxide will attack and dissolve the
following metals: Tin, Aluminum, zinc, cadmium - behaves closely
enough to zinc. It will also attack chromium plating and copper,
although ammonia is far better at dissolving copper:

The reaction with those metals releases hydrogen gas.

Sodium hydroxide will not react with iron or steel, in fact the
alkaline conditions will not allow rust to grow;


What would you use in a frame that has been fully chromed?
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Reasonable? Necessary? You Decide Nuxx Bar UK 135 March 11th 08 11:19 PM
No reasonable expectation of a bike on the side of the road TimC Australia 32 December 8th 06 01:12 AM
Is this just and reasonable? Bill C Racing 16 August 4th 06 02:22 PM
WTB - reasonable tri/TT wheels MJR Marketplace 0 July 6th 06 02:48 PM
LBS reasonable markup Keith Vetter General 57 June 17th 04 03:01 PM


All times are GMT +1. The time now is 01:47 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CycleBanter.com.
The comments are property of their posters.