|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
interchangeable hubs?
I have an old huffy 3-speed, my best guess is that it is from the
1970's. I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. Where would I start to figure out if it's even possible? (Tire size, frame fork, something else?) |
#2
|
|||
|
|||
interchangeable hubs?
On Apr 15, 6:01 pm, Jeff Welch wrote:
I have an old huffy 3-speed, my best guess is that it is from the 1970's. I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. Where would I start to figure out if it's even possible? (Tire size, frame fork, something else?) Sure, it's possible. A Sturmey Archer hub might be a better choice for that frame spacing, if you don't want to spread it. Plenty of options with and without brakes. |
#3
|
|||
|
|||
interchangeable hubs?
In article
, landotter wrote: On Apr 15, 6:01 pm, Jeff Welch wrote: I have an old huffy 3-speed, my best guess is that it is from the 1970's. I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. Where would I start to figure out if it's even possible? (Tire size, frame fork, something else?) Sure, it's possible. A Sturmey Archer hub might be a better choice for that frame spacing, if you don't want to spread it. Plenty of options with and without brakes. To elaborate, you'll almost certainly want to build a new wheel around the Nexus hub, so just find out what the old wheel size was (you can easily determine that from the tire markings or by taking it to a half-competent LBS), and spec the necessary rim from there. The Nexus 7 hubs can be built with rim, roller, or coaster brake setups, so you can preserve the present braking setup or change it as you prefer. As Landotter suggests, an S-A 7-speed will fit in your frame without changing the rear spacing, though potentially at the cost of a bit of efficiency and niceness that the Nexus hubs have. I doubt you'll notice, and if you might, you'll probably want one of the even spiffier 8-speed Nexus/Alfine hubs, or the also-spiffy SRAM iMotion 9 hub. For any of those not-Sturmey hubs, respacing is a mildly unusual mechanical challenge that will require either an enthusiastic amateur or a mostly-competent LBS. If you're taking a DIY approach, you'll need a new rear wheel, spec the brake properly, a new shifter, and the various small parts. Plus you'll need to re-space the frame if you don't go for the S-A 7. Dealing with a shop that has done such a conversion before will help you avoid one of my minor mistakes: if you order, for example, an Alfine hub, the standard Shimano part number (at least around here) gets you a bare hub, but no shifter or cabling (they come together as a separate part number), no cog (your old 3-speed cog will work fine, surprisingly), and no cable attachment thingy, magic lockring thingy, or anti-turn nuts (again, the distributors in my country pack those three pieces into a different part number). Logically ordering just the shifter and the hub will get you a set of elegant-looking mechanical lumps and a bit of research and waiting to find the complete finishing bits. I'd like to thank Dan Burkhart of Boomer Cycle (Ontario) for helping out with that part. In the US, Harris Cyclery is the canonical source knowledge and hubs-in-stock, and their prices are a benchmark, if a beatable one. -- Ryan Cousineau http://www.wiredcola.com/ "In other newsgroups, they killfile trolls." "In rec.bicycles.racing, we coach them." |
#4
|
|||
|
|||
interchangeable hubs?
On Apr 15, 9:30*pm, Ryan Cousineau wrote:
In article , *landotter wrote: On Apr 15, 6:01 pm, Jeff Welch wrote: I have an old huffy 3-speed, my best guess is that it is from the 1970's. *I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. *Where would I start to figure out if it's even possible? *(Tire size, frame fork, something else?) Sure, it's possible. A Sturmey Archer hub might be a better choice for that frame spacing, if you don't want to spread it. Plenty of options with and without brakes. To elaborate, you'll almost certainly want to build a new wheel around the Nexus hub, so just find out what the old wheel size was (you can easily determine that from the tire markings or by taking it to a half-competent LBS), and spec the necessary rim from there. To elaborate tangentially from there, the rim is likely an "26 x 1 3/8" EA3 size, or 590mm, which is right inbetween "road" and "mtb" size wheels. A common and good version is the Sun Cr-18. It's polished aluminum, and looks great on restored rides: http://www.bikemannetwork.com/biking/p/RM8494 27" rims are also readily available. If you're super lucky, though, and the bike is an actual mtb size 26" (559mm), then you can purchase a pre-built Nexus wheel for less than the sum of the parts. One last thing to consider if you want retro with zero work, you can get the really cool Schwinn "Coffee" for $250 in a single speed, and the three speed retails for around $370. Checked one out at my LBS. Looks retro from a distance, but rides like a modern bike. Sweet! http://bikesfortherestofus.blogspot....e-cruiser.html |
#5
|
|||
|
|||
interchangeable hubs?
In article
, landotter wrote: One last thing to consider if you want retro with zero work, you can get the really cool Schwinn "Coffee" for $250 in a single speed, and the three speed retails for around $370. Checked one out at my LBS. Looks retro from a distance, but rides like a modern bike. Sweet! http://bikesfortherestofus.blogspot....e-cruiser.html That is a gracefully retro bike! -- Ryan Cousineau http://www.wiredcola.com/ "In other newsgroups, they killfile trolls." "In rec.bicycles.racing, we coach them." |
#6
|
|||
|
|||
interchangeable hubs?
On Wed, 16 Apr 2008 02:30:10 +0000, Ryan Cousineau wrote:
In article , landotter wrote: On Apr 15, 6:01 pm, Jeff Welch wrote: I have an old huffy 3-speed, my best guess is that it is from the 1970's. I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. Where would I start to figure out if it's even possible? (Tire size, frame fork, something else?) Sure, it's possible. A Sturmey Archer hub might be a better choice for that frame spacing, if you don't want to spread it. Plenty of options with and without brakes. To elaborate, you'll almost certainly want to build a new wheel around the Nexus hub, so just find out what the old wheel size was (you can easily determine that from the tire markings or by taking it to a half-competent LBS), and spec the necessary rim from there. The Nexus 7 hubs can be built with rim, roller, or coaster brake setups, so you can preserve the present braking setup or change it as you prefer. As Landotter suggests, an S-A 7-speed will fit in your frame without changing the rear spacing, though potentially at the cost of a bit of efficiency and niceness that the Nexus hubs have. Does Sturmey make a 7-speed hub? If you mean the 8-speed hub, that may not be a good choice for the OP because the gearing is better suited to small-wheeled bikes: http://sheldonbrown.com/harris/sturmey-archer-hubs.html I doubt you'll notice, and if you might, you'll probably want one of the even spiffier 8-speed Nexus/Alfine hubs, or the also-spiffy SRAM iMotion 9 hub. For any of those not-Sturmey hubs, respacing is a mildly unusual mechanical challenge that will require either an enthusiastic amateur or a mostly-competent LBS. If you're taking a DIY approach, you'll need a new rear wheel, spec the brake properly, a new shifter, and the various small parts. Plus you'll need to re-space the frame if you don't go for the S-A 7. Dealing with a shop that has done such a conversion before will help you avoid one of my minor mistakes: if you order, for example, an Alfine hub, the standard Shimano part number (at least around here) gets you a bare hub, but no shifter or cabling (they come together as a separate part number), no cog (your old 3-speed cog will work fine, surprisingly), and no cable attachment thingy, magic lockring thingy, or anti-turn nuts (again, the distributors in my country pack those three pieces into a different part number). Logically ordering just the shifter and the hub will get you a set of elegant-looking mechanical lumps and a bit of research and waiting to find the complete finishing bits. I'd like to thank Dan Burkhart of Boomer Cycle (Ontario) for helping out with that part. In the US, Harris Cyclery is the canonical source knowledge and hubs-in-stock, and their prices are a benchmark, if a beatable one. |
#7
|
|||
|
|||
interchangeable hubs?
In article ,
Gary Young wrote: On Wed, 16 Apr 2008 02:30:10 +0000, Ryan Cousineau wrote: In article , landotter wrote: On Apr 15, 6:01 pm, Jeff Welch wrote: I have an old huffy 3-speed, my best guess is that it is from the 1970's. I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. Where would I start to figure out if it's even possible? (Tire size, frame fork, something else?) Sure, it's possible. A Sturmey Archer hub might be a better choice for that frame spacing, if you don't want to spread it. Plenty of options with and without brakes. As Landotter suggests, an S-A 7-speed will fit in your frame without changing the rear spacing, though potentially at the cost of a bit of efficiency and niceness that the Nexus hubs have. Does Sturmey make a 7-speed hub? If you mean the 8-speed hub, that may not be a good choice for the OP because the gearing is better suited to small-wheeled bikes: http://sheldonbrown.com/harris/sturmey-archer-hubs.html Argh yes, that's the one. My excuse is that they used to make a 7-speed. Or perhaps I'm just going senile. Nonetheless, while you're roughly right about the gearing (it's really just a matter of the direct-drive gear being the lowest gear; not a fatal issue), the hub's claim to fame is that it can be put into a frame as narrow as 115 mm. -- Ryan Cousineau http://www.wiredcola.com/ "In other newsgroups, they killfile trolls." "In rec.bicycles.racing, we coach them." |
#8
|
|||
|
|||
interchangeable hubs?
On Tue, 15 Apr 2008 22:22:36 -0500, Gary Young wrote:
On Wed, 16 Apr 2008 02:30:10 +0000, Ryan Cousineau wrote: In article , landotter wrote: On Apr 15, 6:01 pm, Jeff Welch wrote: I have an old huffy 3-speed, my best guess is that it is from the 1970's. I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. Where would I start to figure out if it's even possible? (Tire size, frame fork, something else?) Sure, it's possible. A Sturmey Archer hub might be a better choice for that frame spacing, if you don't want to spread it. Plenty of options with and without brakes. To elaborate, you'll almost certainly want to build a new wheel around the Nexus hub, so just find out what the old wheel size was (you can easily determine that from the tire markings or by taking it to a half-competent LBS), and spec the necessary rim from there. The Nexus 7 hubs can be built with rim, roller, or coaster brake setups, so you can preserve the present braking setup or change it as you prefer. As Landotter suggests, an S-A 7-speed will fit in your frame without changing the rear spacing, though potentially at the cost of a bit of efficiency and niceness that the Nexus hubs have. Does Sturmey make a 7-speed hub? If you mean the 8-speed hub, that may not be a good choice for the OP because the gearing is better suited to small-wheeled bikes: Nonsense. The only difference between a small-wheeled version and a large-wheeled version of a successful Nexus conversion are the sizes of the chainring and rear cog; the internal arrangements of the gearhub have no increased suitablilty for wheels of any size. The only considerations of this order that would be of importance are range of gearing available and maximum torque allowed. |
#9
|
|||
|
|||
interchangeable hubs?
On Wed, 16 Apr 2008 12:47:38 +0000, _ wrote:
On Tue, 15 Apr 2008 22:22:36 -0500, Gary Young wrote: On Wed, 16 Apr 2008 02:30:10 +0000, Ryan Cousineau wrote: In article , landotter wrote: On Apr 15, 6:01 pm, Jeff Welch wrote: I have an old huffy 3-speed, my best guess is that it is from the 1970's. I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. Where would I start to figure out if it's even possible? (Tire size, frame fork, something else?) Sure, it's possible. A Sturmey Archer hub might be a better choice for that frame spacing, if you don't want to spread it. Plenty of options with and without brakes. To elaborate, you'll almost certainly want to build a new wheel around the Nexus hub, so just find out what the old wheel size was (you can easily determine that from the tire markings or by taking it to a half-competent LBS), and spec the necessary rim from there. The Nexus 7 hubs can be built with rim, roller, or coaster brake setups, so you can preserve the present braking setup or change it as you prefer. As Landotter suggests, an S-A 7-speed will fit in your frame without changing the rear spacing, though potentially at the cost of a bit of efficiency and niceness that the Nexus hubs have. Does Sturmey make a 7-speed hub? If you mean the 8-speed hub, that may not be a good choice for the OP because the gearing is better suited to small-wheeled bikes: Nonsense. The only difference between a small-wheeled version and a large-wheeled version of a successful Nexus conversion are the sizes of the chainring and rear cog; the internal arrangements of the gearhub have no increased suitablilty for wheels of any size. The only considerations of this order that would be of importance are range of gearing available and maximum torque allowed. Take a look at Sheldon Brown's internal gear calculator: http://sheldonbrown.com/gears/internal.html If the OP has 26-inch wheels, a 170mm crank, and a 40-tooth chainring, then adding the Sturmey-Archer 8-speed hub with its stock 25-tooth sprocket would give him a range of 41.6 to 126.9 gear inches. That strikes me as pretty high for a typical gearhub bike. Now try the Shimano Nexus 8-speed hub with its stock 19-tooth sprocket (all else held equal) and you get a range of 28.8 to 88.4 gear inches. It's true that you could get the Sturmey-Archer down into the Nexus territory with a 28-tooth chainring, but it's my understanding that such a small ring would probably result in rapid wear of the ring and chain (though perhaps I'm mistaken about that). Moreover, the OP, who has an old 3-speed, probably doesn't have a crank with replaceable rings and thus would have to buy a new crank and maybe a new bottom bracket. This problem would be exacerbated if the OP's wheels are larger than 26 inches. So, I don't think it's nonsense to say that the Sturmey-Archer hub is better suited to small-wheeled bicycles (and actually I was just echoing Sheldon Brown's judgment on that). |
#10
|
|||
|
|||
interchangeable hubs?
On Tue, 15 Apr 2008 23:01:11 GMT, Jeff Welch wrote:
I have an old huffy 3-speed, my best guess is that it is from the 1970's. I'm just learning how to maintain and repair my own bike, and was wondering if it is possible to convert the current Shimano 3-speed hub to one of their new Nexus 7-speed hubs. Where would I start to figure out if it's even possible? (Tire size, frame fork, something else?) A point to consider is that the Nexus hubs have a control-cable arrangement that runs inside the chainstay, while the SA hubs have the control-cable running through the axle nut. This means that you may need an anti-rotation washer for the Nexus different than what may be supplied, in order to get the control-cable to run in the direction you wish. These washers have varying degrees of offset between the axle flats and the dropout tangs; I think they are available separately, but you may have to look hard. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Phil Wood Bottom Brackets Interchangeable? | suzyj | Australia | 0 | July 7th 06 04:35 AM |
Are Shimano chainrings interchangeable? | Caleb | Techniques | 16 | May 20th 06 01:45 PM |
Ksyrium SL and Elite freehubs interchangeable? | Chuck Liu | Techniques | 0 | March 18th 06 03:51 AM |
DT Wheelsmith nipples interchangeable? | [email protected] | Techniques | 8 | February 24th 06 01:49 PM |
MegaExo interchangeable with Hollowtech II? | [email protected] | Techniques | 6 | December 12th 05 07:16 PM |