#1
|
|||
|
|||
Headset woes
I have just taken my headset apart and had a bit of a surprise.
Rather than finding a ball/roller races, I found cartridge bearings. The lower bearing is kn*****ed and the LBS have ordered me a new one. No problem there really, but how am I meant to service the bearings if I cannot get them apart to pack in the grease? The bike is a Dawes Galaxy and the headset is a Deore LX. John T. Remove the singers of Spam before replying |
Ads |
#2
|
|||
|
|||
Headset woes
John Tomlinson wrote:
I have just taken my headset apart and had a bit of a surprise. Rather than finding a ball/roller races, I found cartridge bearings. The lower bearing is kn*****ed and the LBS have ordered me a new one. No problem there really, but how am I meant to service the bearings if I cannot get them apart to pack in the grease? The bike is a Dawes Galaxy and the headset is a Deore LX. Most of them are not supposed to be regreased - you just get new cartridges which are pregreased. Some cartridges can be prised apart with a screwdriver, however, but there is a risk of damaging the seals. I find Stronglight O'Light ones work better without the seals! ~PB |
#3
|
|||
|
|||
Headset woes
On Tue, 24 Feb 2004 22:00:23 -0000, "Pete Biggs"
wrote: Most of them are not supposed to be regreased - you just get new cartridges which are pregreased. Some cartridges can be prised apart with a screwdriver, however, but there is a risk of damaging the seals Yep. I did try that very gently but would have caused too much damage; I needed to put the old unit back to use the bike until Friday when the LBS say they will have some for me. But looking at the old cartridge, it is not very well sealed. You can clearly see the balls through a small gap in the housing. So the grease is bound to wash out. I think it was the 150k audax I did in Norfolk the other weekend that washed the grease out of the old unit :-( I find Stronglight O'Light ones work better without the seals! ~PB So, do you take off the seals so you can add your own grease as and when required? JT Remove the singers of Spam before replying |
#4
|
|||
|
|||
Headset woes
John Tomlinson wrote:
Most of them are not supposed to be regreased - you just get new cartridges which are pregreased. Some cartridges can be prised apart with a screwdriver, however, but there is a risk of damaging the seals Yep. I did try that very gently but would have caused too much damage; I needed to put the old unit back to use the bike until Friday when the LBS say they will have some for me. But looking at the old cartridge, it is not very well sealed. You can clearly see the balls through a small gap in the housing. So the grease is bound to wash out. I think it was the 150k audax I did in Norfolk the other weekend that washed the grease out of the old unit :-( You could perhaps try an external boot: Lizzard Skinz or a home made job. I find Stronglight O'Light ones work better without the seals! So, do you take off the seals so you can add your own grease as and when required? From new, I found the headset was binding with the seals so I took them off and leave them off for that reason. Weather protection is compromised but I can regrease when required. In fact I'm only using the top half of the headset now and use an A9 lower. The O'Light has needle bearing cartridges* instead of the ball type that Shimano use. * Poor design IMO: has smaller rollers than A9's and seals are excessivley tight. Might be ok if head tube faces are absolutely perfect. ~PB |
#5
|
|||
|
|||
Headset woes
John Tomlinson wrote:
: I have just taken my headset apart and had a bit of a surprise. : Rather than finding a ball/roller races, I found cartridge bearings. : The lower bearing is kn*****ed and the LBS have ordered me a new one. : No problem there really, but how am I meant to service the bearings if : I cannot get them apart to pack in the grease? For my money, I'd buy a Campag Record headset which has a grease port on the lower race so you can grease it easily. Arthur -- Arthur Clune http://www.clune.org "Technolibertarians make a philosophy out of a personality defect" - Paulina Borsook |
#6
|
|||
|
|||
Headset woes
On Tue, 24 Feb 2004 19:26:33 +0000 (UTC), John Tomlinson
wrote: I have just taken my headset apart and had a bit of a surprise. Rather than finding a ball/roller races, I found cartridge bearings. The lower bearing is kn*****ed and the LBS have ordered me a new one. No problem there really, but how am I meant to service the bearings if I cannot get them apart to pack in the grease? You're not. You're meant to replace them. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cannondale MT800 tandem headset removal question | Tony Healy | Techniques | 2 | April 2nd 04 04:36 PM |
Threadless headset questions/problems | Scott Ghiz | Techniques | 4 | February 18th 04 01:51 PM |