Ads |
#12
|
|||
|
|||
125mm stem HELP
On Mar 18, 2:57*am, "Mike Jacoubowsky"
wrote: ====== 5mm IS anal. *I know, nuts. *I've been riding for a while both with 130mm and 120mm. *I can't change the frame, so I figured I'd go for a 125 stem. *And I'm not a weight freak by any stretch of the imagination. *I would just be better off, and in the same position as my preivous brand bikes on a 125mm. * *Thanks though. Sim ====== As was pointed out previously, you *can* have your 125 measurement, by simply getting a stem with a different angle, and adjusting for the height difference by using spacers above or below it. A 130mm 17degree stem in the "up" position is likely go put you in-between (as in, about 125mm) a 120mm & 130mm 7degree stem (also in the "up" position). And, as somebody else pointed out, you could get a bar with a slightly-different forward reach. If you don't spend much time on the center straight part of the bar, this will work just as well as a different stem.. Lots of ways to get there, once you've defined where "there" is. --Mike Jacoubowsky Chain Reaction Bicycleswww.ChainReaction.com Redwood City & Los Altos, CA USA "Sim" wrote in message ... On Mar 17, 3:43 pm, Anton Berlin wrote: On Mar 17, 5:12 am, Sim wrote: HELP! I'm looking for a 125mm road stem (31.8 clamp) I've looked around and can't find one. It doesn't seem as if QBP have any. Doesn't anyone out there at least know of any brands who if nothing else "claim" to make a 125mm stem? Preferably not carbon and not overpriced, not adjustable or anything silly like that. Someone told me the Deda Newton comes in a 125, but QBP don't seem to stock it. Any help much appreciated. cheers Sim Green Buddy if you're this worried about position, you probably are one of those freaks trying to shave 3 gms off of your rotational weight. Here's a tip, take a big dump for every race and if you're still not winning, hit the needle. 5mm is anal. 5mm IS anal. *I know, nuts. *I've been riding for a while both with 130mm and 120mm. *I can't change the frame, so I figured I'd go for a 125 stem. *And I'm not a weight freak by any stretch of the imagination. *I would just be better off, and in the same position as my preivous brand bikes on a 125mm. * *Thanks though. Sim- Hide quoted text - - Show quoted text - In the "UP" position? You mean upside down. I'm not riding a hybrid!!! And I have gone over other measurements, I'm not new to this, though I guess I should have said that. Cheers though. SIm |
#13
|
|||
|
|||
125mm stem HELP
On Mar 18, 4:08*am, "z, fred" wrote:
wrote: On Mar 17, 5:12 am, Sim wrote: HELP! *I'm looking for a 125mm road stem (31.8 clamp) *I've looked around and can't find one. *It doesn't seem as if QBP have any. Doesn't anyone out there at least know of any brands who if nothing else "claim" to make a 125mm stem? *Preferably not carbon and not overpriced, not adjustable or anything silly like that. *Someone told me the Deda Newton comes in a 125, but QBP don't seem to stock it. Any help much appreciated. cheers Sim Green Get a Llwellen Stem kit (steel) and have one made to the exact length you want. http://www.coloradocyclist.com/product/item/LOOLBTE1 Now this is interesting... Llewellen, as in the Aussie frame maker? |
#14
|
|||
|
|||
125mm stem HELP
On Mar 18, 12:53*am, Sim wrote:
On Mar 18, 2:57*am, "Mike Jacoubowsky" wrote: As was pointed out previously, you *can* have your 125 measurement, by simply getting a stem with a different angle, and adjusting for the height difference by using spacers above or below it. A 130mm 17degree stem in the "up" position is likely go put you in-between (as in, about 125mm) a 120mm & 130mm 7degree stem (also in the "up" position). And, as somebody else pointed out, you could get a bar with a slightly-different forward reach. If you don't spend much time on the center straight part of the bar, this will work just as well as a different stem. Lots of ways to get there, once you've defined where "there" is. In the "UP" position? *You mean upside down. *I'm not riding a hybrid!!! And I have gone over other measurements, I'm not new to this, though I guess I should have said that. *Cheers though. SIm If you're not new to this, then you should have figured out that bar position is some combination of stem rise, angle and handle bar extension, and that Mike is right, there are multiple ways to get the bars into any given position: http://www.habcycles.com/fitting.html Also, this isn't really a question worth crossposting for. Ben |
#15
|
|||
|
|||
125mm stem HELP
Op 18-03-10 19:14, Fredmaster of Brainerd wrote:
Also, this isn't really a question worth crossposting for. Even worse: it's not crossposted. |
#16
|
|||
|
|||
125mm stem HELP
On Mar 18, 12:07*pm, "A. Dumas Fred" wrote:
Op 18-03-10 19:14, Fredmaster of Brainerd wrote: Also, this isn't really a question worth crossposting for. Even worse: it's not crossposted. You're right and I am a dumbass. Okay, since this is rbr: the correct answer is to quit fantasizing about a 125mm stem. Just get a 120mm stem and sweat 5mm of padding off your ass. The bike will fit better and your performance will improve. |
#17
|
|||
|
|||
125mm stem HELP
On Mar 18, 2:37*pm, Fredmaster of Brainerd wrote:
On Mar 18, 12:07*pm, "A. Dumas Fred" wrote: Op 18-03-10 19:14, Fredmaster of Brainerd wrote: Also, this isn't really a question worth crossposting for. Even worse: it's not crossposted. You're right and I am a dumbass. Okay, since this is rbr: *the correct answer is to quit fantasizing about a 125mm stem. *Just get a 120mm stem and sweat 5mm of padding off your ass. *The bike will fit better and your performance will improve. Or, stop wearing Depends under your cycling shorts. |
#18
|
|||
|
|||
125mm stem HELP
On Mar 18, 10:57*pm, Scott wrote:
On Mar 18, 2:37*pm, Fredmaster of Brainerd wrote: On Mar 18, 12:07*pm, "A. Dumas Fred" wrote: Op 18-03-10 19:14, Fredmaster of Brainerd wrote: Also, this isn't really a question worth crossposting for. Even worse: it's not crossposted. You're right and I am a dumbass. Okay, since this is rbr: *the correct answer is to quit fantasizing about a 125mm stem. *Just get a 120mm stem and sweat 5mm of padding off your ass. *The bike will fit better and your performance will improve. Or, stop wearing Depends under your cycling shorts. Hmmm, getting a lot less helpful and seem to be making assumptions about my size, weight, knowledge, experience. It was a simple quesition, "does anyone know where I can get a 125mm stem". Maybe this RBR thing wasn't the place for it. Thanks to those who did help. |
#19
|
|||
|
|||
125mm stem HELP
On Mar 18, 11:34*pm, DepartFictif wrote:
On Mar 18, 10:57*pm, Scott wrote: On Mar 18, 2:37*pm, Fredmaster of Brainerd wrote: On Mar 18, 12:07*pm, "A. Dumas Fred" wrote: Op 18-03-10 19:14, Fredmaster of Brainerd wrote: Also, this isn't really a question worth crossposting for. Even worse: it's not crossposted. You're right and I am a dumbass. Okay, since this is rbr: *the correct answer is to quit fantasizing about a 125mm stem. *Just get a 120mm stem and sweat 5mm of padding off your ass. *The bike will fit better and your performance will improve. Or, stop wearing Depends under your cycling shorts. Hmmm, getting a lot less helpful and seem to be making assumptions about my size, weight, knowledge, experience. *It was a simple quesition, "does anyone know where I can get a 125mm stem". *Maybe this RBR thing wasn't the place for it. Thanks to those who did help.- Hide quoted text - - Show quoted text - Dam it, someone else used my computer. Previous post was from me! Sim PS: What's "crossposting"? |
#20
|
|||
|
|||
125mm stem HELP
On Mar 18, 4:34*pm, DepartFictif wrote:
On Mar 18, 10:57*pm, Scott wrote: On Mar 18, 2:37*pm, Fredmaster of Brainerd wrote: On Mar 18, 12:07*pm, "A. Dumas Fred" wrote: Op 18-03-10 19:14, Fredmaster of Brainerd wrote: Also, this isn't really a question worth crossposting for. Even worse: it's not crossposted. You're right and I am a dumbass. Okay, since this is rbr: *the correct answer is to quit fantasizing about a 125mm stem. *Just get a 120mm stem and sweat 5mm of padding off your ass. *The bike will fit better and your performance will improve. Or, stop wearing Depends under your cycling shorts. Hmmm, getting a lot less helpful and seem to be making assumptions about my size, weight, knowledge, experience. *It was a simple quesition, "does anyone know where I can get a 125mm stem". *Maybe this RBR thing wasn't the place for it. Thanks to those who did help. To be honest, I did try to help earlier when I suggested just getting a handlebar with a slightly longer reach. I could also have suggested that you just get a 120 and pretend it is a 125. That would work, too. FWIW, no one was making any assumptions about your size, weight, etc... the joking comments were all in good fun, and if you'll notice they didn't start until after you'd already received plenty of useful answers to your question. Well, maybe Anton Berlin started a little early, but that's just his nature. I'm not sure he knows how to give a straight answer, but that doesn't stop him from giving an answer. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
WTB: ITM Goccia or 3ttt Record stem 125mm | walter | Marketplace | 0 | June 19th 09 10:37 PM |
125mm cranks really don't like my ankles | net_hippy | Unicycling | 4 | May 17th 08 06:28 PM |
GIANT 125MM CARBON ROAD STEM $59.00 Shipperd | Kirkland King | Marketplace | 0 | March 14th 05 04:36 PM |
GIANT COMPONENTS 125MM CARBON ROAD STEM $59.00 Shipperd | Kirkland King | Marketplace | 0 | March 12th 05 04:31 PM |
torker dx 125mm crank | chickenloaf_au | Unicycling | 0 | January 23rd 05 01:37 PM |