|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
Ok, so I've had a few rides on my new Schlumpf and I tightened one shifter button a little too hard and it's stuck. I can' remove the little inner screw- I think I might have rounded it off trying. Not a problem...it's still rideable. At least until today, because now the crank is loose on that side. I don't know how on earth I'm supposed to tighten that crank when the Schlumpf button is in the way, and stuck!!!! Any ideas? Cheers, Ken p/s Not related to the above, but on the other side, I snapped the mushroom dome of the Schlumpf button, so all I have is the bit that screws into the hub -- GizmoDuck The Induni Unicycle Tour 2009. Unicycle Tour of India. Email me for details. www.induni.adventureunicyclist.com The Uninam Tour 2008.....Hanoi to Saigon!!! www.uninam.net The SINZ Unicycle Tour 2007....South Island, New Zealand www.sinzuni.org ------------------------------------------------------------------------ GizmoDuck's Profile: http://www.unicyclist.com/profile/794 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
Ads |
#2
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
I wouldn't know either how to tighten the crank with the button in the way. Those tiny screws are easily overtightened indeed, I had a similar issue as well. In my case, the Allen bit snapped during tightening. At first I didn't notice the snapping, and it felt as if the screw was rounded. So - make sure your Allen bit is OK. If it is, the only other option I see is to drill out the little screw and get a replacement, carefully though or you might damage the threaded hole it sits in! That or sending it back to Florian who, if he has time, will perform some magic. Come to think of it, a third option is to ask some magic advice from Florian. Not sure I understand what happened at the other side. Was it that the dome-shaped bigger part of the shifter button broke apart from the stem with which the button is tightened to the shifter shaft, so you only have the middle part still on? Man, you're hard on the thing! -- Klaas Bil ------------------------------------------------------------------------ Klaas Bil's Profile: http://www.unicyclist.com/profile/3442 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#3
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
GizmoDuck;1121677 wrote: Ok, so I've had a few rides on my new Schlumpf and I tightened one shifter button a little too hard and it's stuck. I can' remove the little inner screw- I think I might have rounded it off trying. Is the new KH hub, or the original Schlumpf one? I know the original ones had two grooves in the top of the button and came with a special tool that fitted in there to hold it still whilst tightening the grub screw. If that's the case, then you might be able to try to unscrew the whole button (which will take the grub screw with it) whilst holding the shattered remains of the other button with some big pliers. For that to work, however, the grub screw in the other button needs to be tighter than the one you can't get out. An alternative would be to take off the broken button, and get hold of two very small nuts that fit on the shaft. If these are put on far enough, and tightened against each other, then that will give you a safer, easier way to hold the shaft whilst unscrewing the button with the stuck grub screw. Or else, you could just buy a new hub... and I'll pay the postage for you to send me the old one STM -- semach.the.monkey ------------------------------------------------------------------------ semach.the.monkey's Profile: http://www.unicyclist.com/profile/12078 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#4
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
Klaas Bil;1121699 wrote: I wouldn't know either how to tighten the crank with the button in the way. Those tiny screws are easily overtightened indeed, I had a similar issue as well. In my case, the Allen bit snapped during tightening. At first I didn't notice the snapping, and it felt as if the screw was rounded. So - make sure your Allen bit is OK. If it is, the only other option I see is to drill out the little screw and get a replacement, carefully though or you might damage the threaded hole it sits in! That or sending it back to Florian who, if he has time, will perform some magic. Come to think of it, a third option is to ask some magic advice from Florian. Not sure I understand what happened at the other side. Was it that the dome-shaped bigger part of the shifter button broke apart from the stem with which the button is tightened to the shifter shaft, so you only have the middle part still on? Man, you're hard on the thing! I have emailed Florian. Waiting for an answer but I'm in a bit of a hurry due to a pending record attempt in a couple of weeks How could you possibly snap the little inner bolt? Isn't it inside the button? I don't think drilling is an option... And yes, I broke the dome part where it connects to the stem. I haven't actually ridden the Sclumpf much...probably only about 50-60km so far. A bit dissapointed that it just fell to bits when I tried to shift into gear. -- GizmoDuck The Induni Unicycle Tour 2009. Unicycle Tour of India. Email me for details. www.induni.adventureunicyclist.com The Uninam Tour 2008.....Hanoi to Saigon!!! www.uninam.net The SINZ Unicycle Tour 2007....South Island, New Zealand www.sinzuni.org ------------------------------------------------------------------------ GizmoDuck's Profile: http://www.unicyclist.com/profile/794 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#5
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
semach.the.monkey;1121714 wrote: Is the new KH hub, or the original Schlumpf one? I know the original ones had two grooves in the top of the button and came with a special tool that fitted in there to hold it still whilst tightening the grub screw. If that's the case, then you might be able to try to unscrew the whole button (which will take the grub screw with it) whilst holding the shattered remains of the other button with some big pliers. For that to work, however, the grub screw in the other button needs to be tighter than the one you can't get out. An alternative would be to take off the broken button, and get hold of two very small nuts that fit on the shaft. If these are put on far enough, and tightened against each other, then that will give you a safer, easier way to hold the shaft whilst unscrewing the button with the stuck grub screw. Or else, you could just buy a new hub... and I'll pay the postage for you to send me the old one STM It's the new KH Schlumpf hub. I was considering your first option, but if I tightened the broken grub screw on the other side, it would just jam that button in there instead of the one that is currently stuck! I'm going to see if I can do your second option, but it means finding a very narrow pair of pliers to grip it I think. Your third option is not feasible because I need it for a record attempt in two weeks time. Note that in order to get my KH 36" rideable, I actually had to buy a second frame because my first (brand new) frame ended up with a jammed seatpost. (see my earlier post on using pipe cutters) -- GizmoDuck The Induni Unicycle Tour 2009. Unicycle Tour of India. Email me for details. www.induni.adventureunicyclist.com The Uninam Tour 2008.....Hanoi to Saigon!!! www.uninam.net The SINZ Unicycle Tour 2007....South Island, New Zealand www.sinzuni.org ------------------------------------------------------------------------ GizmoDuck's Profile: http://www.unicyclist.com/profile/794 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#6
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
I'm presuming you've rounded the allen key bolt, so the allen key just spins in it, it isn't just that it is very tight? If it is rounded, and unscrewing the other side doesn't loosen it enough, the only option is to drill it out. Unless you are very very exact, you need a new button, as you will destroy the button doing this. I had to do this, and I certainly needed a new button. Be careful not to bugger the shifty shaft. On other possible option is to use an easy-out / screw extractor. They are a left hand drill bit, basically you drill a little pilot hole with a normal drill bit, stick the easy out in, turn the drill to reverse, and they will dig in and unscrew the bolt (thanks to being left hand thread the drill action loosens the bolt) . You'd need to hold the button with pliers when you did this, or else it'd just screw it up. Hardware shops sell them. You'd need a pretty narrow one for a schlumpf screw though, and they are a bit brittle sometimes, so a bit risky. It will destroy the screw, but maybe not the button if you're lucky. http://tinyurl.com/5k2qlj Joe -- joemarshall ' old pics' (http://tinyurl.com/56yl2f) 'new zealand pics' (http://s119.photobucket.com/albums/o...rshall_photos/) 'new pics' (http://picasaweb.google.co.uk/joemarshall.org.uk) 'Where have I been riding? (GPS) ' (http://tinyurl.com/6fxw5x) ------------------------------------------------------------------------ joemarshall's Profile: http://www.unicyclist.com/profile/1545 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#7
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
GizmoDuck;1121730 wrote: How could you possibly snap the little inner bolt? Isn't it inside the button? No I didn't snap the little bolt. When I wrote I snapped the Allen bit, I actually meant the Allen -bit-. See this pic, which is my broken one: the thin end broke off while I tightened the little screw. The Schlumpf procedure says to tighten "very firmly (1.1 Nm)". I don't have a torque screwdriver so I just guessed how tight it should be. Misguided by the words "very firmly", I apparently guessed wrong. When I later tried using this broken tool to undo the little screw (without realising the tool was amputated), it felt as if either the screw or the tool was rounded. That's why I wrote "Check if your Allen tool is OK". Florian sent a replacement Allen bit and all was good. +-------------------------------------------------------------------+ |Filename: Schlumpf_Allen_tool.jpg | |Download: http://www.unicyclist.com/attachment/29352 | +-------------------------------------------------------------------+ -- Klaas Bil ------------------------------------------------------------------------ Klaas Bil's Profile: http://www.unicyclist.com/profile/3442 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#8
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
Klaas Bil;1122373 wrote: No I didn't snap the little bolt. When I wrote I snapped the Allen bit, I actually meant the Allen -bit-. See this pic, which is my broken one: the thin end broke off while I tightened the little screw. The Schlumpf procedure says to tighten "very firmly (1.1 Nm)". I don't have a torque screwdriver so I just guessed how tight it should be. Misguided by the words "very firmly", I apparently guessed wrong. When I later tried using this broken tool to undo the little screw (without realising the tool was amputated), it felt as if either the screw or the tool was rounded. That's why I wrote "Check if your Allen tool is OK". Florian sent a replacement Allen bit and all was good. It's for the KH Schlumpf hub, not the Road Schlumpf hub. It uses a 2.5mm allen key instead. Unfortunately, my hub never came with one, because it was confiscated from UDC by the airport when they were bringing it back to NZ. Apparently a 2.5mm allen key can be used as an offensive weapon -- GizmoDuck The Induni Unicycle Tour 2009. Unicycle Tour of India. Email me for details. www.induni.adventureunicyclist.com The Uninam Tour 2008.....Hanoi to Saigon!!! www.uninam.net The SINZ Unicycle Tour 2007....South Island, New Zealand www.sinzuni.org ------------------------------------------------------------------------ GizmoDuck's Profile: http://www.unicyclist.com/profile/794 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#9
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
GizmoDuck;1122484 wrote: It's for the KH Schlumpf hub, not the Road Schlumpf hub. It uses a 2.5mm allen key instead. Ah, now we (or at least: I) know that the little screws are different in the two hubs, because the bit that comes with the road hub is effectively a 1.5 mm allen key. I guess then that the KH Schlumpf hub doesn't come with a recommended tightening torque for that screw? Because to apply a specified torque you need a bit as opposed to a regular allen key, to put in your torque screwdriver, right? -- Klaas Bil ------------------------------------------------------------------------ Klaas Bil's Profile: http://www.unicyclist.com/profile/3442 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#10
|
|||
|
|||
Help! Stuck Schlumpf Shifter Button
Klaas Bil;1122496 wrote: Ah, now we (or at least: I) know that the little screws are different in the two hubs, because the bit that comes with the road hub is effectively a 1.5 mm allen key. I guess then that the KH Schlumpf hub doesn't come with a recommended tightening torque for that screw? Because to apply a specified torque you need a bit as opposed to a regular allen key, to put in your torque screwdriver, right? 50 Nm But who on earth carries a torque lever in their toolkit anyway? I want to throw the damn thing out the window. Just spent the last hour trying to hold the shfit shaft and unscrew the stuck button, now I think I've damaged the threads on it. -- GizmoDuck The Induni Unicycle Tour 2009. Unicycle Tour of India. Email me for details. www.induni.adventureunicyclist.com The Uninam Tour 2008.....Hanoi to Saigon!!! www.uninam.net The SINZ Unicycle Tour 2007....South Island, New Zealand www.sinzuni.org ------------------------------------------------------------------------ GizmoDuck's Profile: http://www.unicyclist.com/profile/794 View this thread: http://www.unicyclist.com/thread/73859 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help! Stuck Schlumpf Shifter Button | GizmoDuck | Unicycling | 1 | October 31st 08 02:13 PM |