A Cycling & bikes forum. CycleBanter.com

Go Back   Home » CycleBanter.com forum » rec.bicycles » Techniques
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Patent updates



 
 
Thread Tools Display Modes
  #1  
Old November 7th 19, 08:31 PM posted to rec.bicycles.tech
AMuzi
external usenet poster
 
Posts: 13,447
Default Patent updates

We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/
--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971

Ads
  #2  
Old November 7th 19, 11:30 PM posted to rec.bicycles.tech
Tom Kunich[_5_]
external usenet poster
 
Posts: 1,231
Default Patent updates

On Thursday, November 7, 2019 at 11:31:54 AM UTC-8, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/
--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


I would wonder how you could ever thread a hose/outer cable through that much of a length of bike without an actual inside tube.
  #3  
Old November 7th 19, 11:44 PM posted to rec.bicycles.tech
AMuzi
external usenet poster
 
Posts: 13,447
Default Patent updates

On 11/7/2019 4:30 PM, Tom Kunich wrote:
On Thursday, November 7, 2019 at 11:31:54 AM UTC-8, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/


I would wonder how you could ever thread a hose/outer cable through that much of a length of bike without an actual inside tube.


Depends on the frame and how much impedimenta is hidden
inside. On some, drop in wire or hose, catch it in one's
fingers through the big hole in front of the BB. For many,
neodymium magnets and a stiff poly wire are the quickest
solution. Others need something to pierce the swarf inside
like a 1/16" welding rod. Then there are the odd frames now
and again which just resist cable/hose installation for no
good reason and tick off the mechanic.

Typical tool:
https://jagwire.com/products/tools/i...l-routing-tool

--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


  #4  
Old November 8th 19, 12:41 AM posted to rec.bicycles.tech
JBeattie
external usenet poster
 
Posts: 5,870
Default Patent updates

On Thursday, November 7, 2019 at 2:44:57 PM UTC-8, AMuzi wrote:
On 11/7/2019 4:30 PM, Tom Kunich wrote:
On Thursday, November 7, 2019 at 11:31:54 AM UTC-8, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/


I would wonder how you could ever thread a hose/outer cable through that much of a length of bike without an actual inside tube.


Depends on the frame and how much impedimenta is hidden
inside. On some, drop in wire or hose, catch it in one's
fingers through the big hole in front of the BB. For many,
neodymium magnets and a stiff poly wire are the quickest
solution. Others need something to pierce the swarf inside
like a 1/16" welding rod. Then there are the odd frames now
and again which just resist cable/hose installation for no
good reason and tick off the mechanic.

Typical tool:
https://jagwire.com/products/tools/i...l-routing-tool


If you're doing a bare frame, it's a PITA but not horrible. It is horrible if you're trying to snake a Di2 wire or hose or cable through a crowded DT into a little passage under the BB with existing cables/hoses/wires. And let's see what's behind door number one! https://tinyurl.com/yy9xwxwb This is the great time suck with modern bikes -- along with hidden nipples in pre-fab wheels and a few other annoyances.

-- Jay Beattie.

-- Jay Beattie.
  #5  
Old November 8th 19, 12:51 AM posted to rec.bicycles.tech
James[_8_]
external usenet poster
 
Posts: 6,153
Default Patent updates

On 8/11/19 6:31 am, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/


Oh how I long for all electric wireless brakes and gears.

--
JS
  #6  
Old November 8th 19, 02:22 AM posted to rec.bicycles.tech
AMuzi
external usenet poster
 
Posts: 13,447
Default Patent updates

On 11/7/2019 5:41 PM, jbeattie wrote:
On Thursday, November 7, 2019 at 2:44:57 PM UTC-8, AMuzi wrote:
On 11/7/2019 4:30 PM, Tom Kunich wrote:
On Thursday, November 7, 2019 at 11:31:54 AM UTC-8, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/


I would wonder how you could ever thread a hose/outer cable through that much of a length of bike without an actual inside tube.


Depends on the frame and how much impedimenta is hidden
inside. On some, drop in wire or hose, catch it in one's
fingers through the big hole in front of the BB. For many,
neodymium magnets and a stiff poly wire are the quickest
solution. Others need something to pierce the swarf inside
like a 1/16" welding rod. Then there are the odd frames now
and again which just resist cable/hose installation for no
good reason and tick off the mechanic.

Typical tool:
https://jagwire.com/products/tools/i...l-routing-tool


If you're doing a bare frame, it's a PITA but not horrible. It is horrible if you're trying to snake a Di2 wire or hose or cable through a crowded DT into a little passage under the BB with existing cables/hoses/wires. And let's see what's behind door number one! https://tinyurl.com/yy9xwxwb This is the great time suck with modern bikes -- along with hidden nipples in pre-fab wheels and a few other annoyances.

-- Jay Beattie.

-- Jay Beattie.


We love Door #1! A finger fits in there.

annoyances
We miss engineeers. Once they were replaced by 'designers'
we were screwed.

--
Andrew Muzi
www.yellowjersey.org/
Open every day since 1 April, 1971


  #7  
Old November 8th 19, 05:34 AM posted to rec.bicycles.tech
JBeattie
external usenet poster
 
Posts: 5,870
Default Patent updates

On Thursday, November 7, 2019 at 5:22:17 PM UTC-8, AMuzi wrote:
On 11/7/2019 5:41 PM, jbeattie wrote:
On Thursday, November 7, 2019 at 2:44:57 PM UTC-8, AMuzi wrote:
On 11/7/2019 4:30 PM, Tom Kunich wrote:
On Thursday, November 7, 2019 at 11:31:54 AM UTC-8, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/

I would wonder how you could ever thread a hose/outer cable through that much of a length of bike without an actual inside tube.


Depends on the frame and how much impedimenta is hidden
inside. On some, drop in wire or hose, catch it in one's
fingers through the big hole in front of the BB. For many,
neodymium magnets and a stiff poly wire are the quickest
solution. Others need something to pierce the swarf inside
like a 1/16" welding rod. Then there are the odd frames now
and again which just resist cable/hose installation for no
good reason and tick off the mechanic.

Typical tool:
https://jagwire.com/products/tools/i...l-routing-tool


If you're doing a bare frame, it's a PITA but not horrible. It is horrible if you're trying to snake a Di2 wire or hose or cable through a crowded DT into a little passage under the BB with existing cables/hoses/wires. And let's see what's behind door number one! https://tinyurl.com/yy9xwxwb This is the great time suck with modern bikes -- along with hidden nipples in pre-fab wheels and a few other annoyances.

-- Jay Beattie.

-- Jay Beattie.


We love Door #1! A finger fits in there.

annoyances
We miss engineeers. Once they were replaced by 'designers'
we were screwed.


What is actually behind door number one is a cramped raceway under the BB insert with, if you can see through it, a small hole into the DT where you catch incoming cables, hoses, wires, etc. Its a nice door, but on my old Roubaix, for example, it covers a cramped warren of wires and hoses.

-- Jay Beattie
  #8  
Old November 8th 19, 10:18 AM posted to rec.bicycles.tech
[email protected]
external usenet poster
 
Posts: 824
Default Patent updates

On Friday, November 8, 2019 at 12:41:37 AM UTC+1, jbeattie wrote:
On Thursday, November 7, 2019 at 2:44:57 PM UTC-8, AMuzi wrote:
On 11/7/2019 4:30 PM, Tom Kunich wrote:
On Thursday, November 7, 2019 at 11:31:54 AM UTC-8, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/


I would wonder how you could ever thread a hose/outer cable through that much of a length of bike without an actual inside tube.


Depends on the frame and how much impedimenta is hidden
inside. On some, drop in wire or hose, catch it in one's
fingers through the big hole in front of the BB. For many,
neodymium magnets and a stiff poly wire are the quickest
solution. Others need something to pierce the swarf inside
like a 1/16" welding rod. Then there are the odd frames now
and again which just resist cable/hose installation for no
good reason and tick off the mechanic.

Typical tool:
https://jagwire.com/products/tools/i...l-routing-tool


If you're doing a bare frame, it's a PITA but not horrible. It is horrible if you're trying to snake a Di2 wire or hose or cable through a crowded DT into a little passage under the BB with existing cables/hoses/wires. And let's see what's behind door number one! https://tinyurl.com/yy9xwxwb This is the great time suck with modern bikes -- along with hidden nipples in pre-fab wheels and a few other annoyances.

-- Jay Beattie.

-- Jay Beattie.


Last week I replaced for the first time the inner cables of the front and rear derailleur of my internal routed Canyon frame. It was very easy. The frame has a big removable plastic cap on the bottom of the bottom bracket shell with the cable guides integrated. I removed the cranks and put a liner (a piece of the smallest shrink tube) from the RD side over the old cable to the BB shell in the horizontal chainstay. After that it is a piece of cake..

Lou
  #9  
Old November 8th 19, 03:51 PM posted to rec.bicycles.tech
JBeattie
external usenet poster
 
Posts: 5,870
Default Patent updates

On Friday, November 8, 2019 at 1:18:13 AM UTC-8, wrote:
On Friday, November 8, 2019 at 12:41:37 AM UTC+1, jbeattie wrote:
On Thursday, November 7, 2019 at 2:44:57 PM UTC-8, AMuzi wrote:
On 11/7/2019 4:30 PM, Tom Kunich wrote:
On Thursday, November 7, 2019 at 11:31:54 AM UTC-8, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/

I would wonder how you could ever thread a hose/outer cable through that much of a length of bike without an actual inside tube.


Depends on the frame and how much impedimenta is hidden
inside. On some, drop in wire or hose, catch it in one's
fingers through the big hole in front of the BB. For many,
neodymium magnets and a stiff poly wire are the quickest
solution. Others need something to pierce the swarf inside
like a 1/16" welding rod. Then there are the odd frames now
and again which just resist cable/hose installation for no
good reason and tick off the mechanic.

Typical tool:
https://jagwire.com/products/tools/i...l-routing-tool


If you're doing a bare frame, it's a PITA but not horrible. It is horrible if you're trying to snake a Di2 wire or hose or cable through a crowded DT into a little passage under the BB with existing cables/hoses/wires. And let's see what's behind door number one! https://tinyurl.com/yy9xwxwb This is the great time suck with modern bikes -- along with hidden nipples in pre-fab wheels and a few other annoyances.

-- Jay Beattie.

-- Jay Beattie.


Last week I replaced for the first time the inner cables of the front and rear derailleur of my internal routed Canyon frame. It was very easy. The frame has a big removable plastic cap on the bottom of the bottom bracket shell with the cable guides integrated. I removed the cranks and put a liner (a piece of the smallest shrink tube) from the RD side over the old cable to the BB shell in the horizontal chainstay. After that it is a piece of cake.

Lou


Changing a cable isn't terrible. On my Norco, for example, the RD cable is all in housing. Installing the housing is a PITA getting it through the chain stay, but once in, cable replacement is easy. The FD cable is in housing from the lever to the DT, but then it stops and runs bare through the frame. My technique for running the FD cable is to pull the old cable just a bit out of the lever, cut off the button, pull off the outer housing and then I cut off a cable end cap so it has a hole in both ends, put the new cable through the lever, through the housing and crimp it to old cable with the cable cap and then just pull it through the frame. The openings are big enough to accommodate the cable cap, and then I just clip it off since there is so much excess cable anyway. I suppose I could use shrink wrap to join the cable for the pull, but I've never tried that. Running a new hydraulic hose or cable housing can be a pain depending on the frame and circumstances. My worst experience was running a new hose through a Roubaix when I couldn't use the old hose to pull because the meth-heads who stole the bike (the police brought it back) had cut the rear tube and shoved the end in the stay.

-- Jay Beattie

-- Jay Beattie.
  #10  
Old November 8th 19, 07:57 PM posted to rec.bicycles.tech
Frank Krygowski[_4_]
external usenet poster
 
Posts: 10,538
Default Patent updates

On 11/8/2019 9:51 AM, jbeattie wrote:

On Friday, November 8, 2019 at 1:18:13 AM UTC-8, wrote:

On Friday, November 8, 2019 at 12:41:37 AM UTC+1, jbeattie wrote:

On Thursday, November 7, 2019 at 2:44:57 PM UTC-8, AMuzi wrote:
On 11/7/2019 4:30 PM, Tom Kunich wrote:
On Thursday, November 7, 2019 at 11:31:54 AM UTC-8, AMuzi wrote:
We all pause to slap our foreheads.
WTF? These are patentable designs??

https://bikerumor.com/2019/11/04/pat...es-for-others/

I would wonder how you could ever thread a hose/outer cable through that much of a length of bike without an actual inside tube.


Depends on the frame and how much impedimenta is hidden
inside. On some, drop in wire or hose, catch it in one's
fingers through the big hole in front of the BB. For many,
neodymium magnets and a stiff poly wire are the quickest
solution. Others need something to pierce the swarf inside
like a 1/16" welding rod. Then there are the odd frames now
and again which just resist cable/hose installation for no
good reason and tick off the mechanic.

Typical tool:
https://jagwire.com/products/tools/i...l-routing-tool

If you're doing a bare frame, it's a PITA but not horrible. It is horrible if you're trying to snake a Di2 wire or hose or cable through a crowded DT into a little passage under the BB with existing cables/hoses/wires. And let's see what's behind door number one! https://tinyurl.com/yy9xwxwb This is the great time suck with modern bikes -- along with hidden nipples in pre-fab wheels and a few other annoyances.

-- Jay Beattie.

-- Jay Beattie.


Last week I replaced for the first time the inner cables of the front and rear derailleur of my internal routed Canyon frame. It was very easy. The frame has a big removable plastic cap on the bottom of the bottom bracket shell with the cable guides integrated. I removed the cranks and put a liner (a piece of the smallest shrink tube) from the RD side over the old cable to the BB shell in the horizontal chainstay. After that it is a piece of cake.

Lou


Changing a cable isn't terrible. On my Norco, for example, the RD cable is all in housing. Installing the housing is a PITA getting it through the chain stay, but once in, cable replacement is easy. The FD cable is in housing from the lever to the DT, but then it stops and runs bare through the frame. My technique for running the FD cable is to pull the old cable just a bit out of the lever, cut off the button, pull off the outer housing and then I cut off a cable end cap so it has a hole in both ends, put the new cable through the lever, through the housing and crimp it to old cable with the cable cap and then just pull it through the frame. The openings are big enough to accommodate the cable cap, and then I just clip it off since there is so much excess cable anyway. I suppose I could use shrink wrap to join the cable for the pull, but I've never tried that. Running a new hydraulic hose or cable housing can be a pain depending on the frame and circumstances. My worst experience was running a new hose through a Roubaix when I couldn't use the old hose to pull because the meth-heads who stole the bike (the police brought it back) had cut the rear tube and shoved the end in the stay.


I don't doubt that there are many clever ways of fishing cables through
frame tubes. But isn't it amazing what people will put up with for
aesthetics?


--
- Frank Krygowski
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Patent News AMuzi Techniques 3 October 31st 19 07:23 PM
Patent number: 528145 [email protected] Techniques 10 January 25th 08 06:25 AM
A WORD FROM THE PATENT OFFICE datakoll Techniques 0 December 25th 07 02:55 AM
Rolf patent misleading Mike Reed Techniques 2 June 2nd 06 07:22 AM
10 collars patent [email protected] General 0 May 20th 05 09:17 AM


All times are GMT +1. The time now is 09:00 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CycleBanter.com.
The comments are property of their posters.