|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
tap size for nimbus isis hub threads??
hello, i have a nimbus hub that was crossthreaded a little bit, and i need to run a tap through to clean it out. the damage is not serious enough to ruin the threads, but i am unsure of the actual thread measurements. i'm fairly certain it is m11x1.00. can anyone confirm or correct that measurement?? thanks! -- OneWheelLess sigg ------------------------------------------------------------------------ OneWheelLess's Profile: http://www.unicyclist.com/profile/16793 View this thread: http://www.unicyclist.com/thread/75188 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
Ads |
#2
|
|||
|
|||
tap size for nimbus isis hub threads??
I think its 12 not 11. But I am not too sure about this. -- agentQ --- 'Uneed Films' (http://www.uneedfilms.com) ------------------------------------------------------------------------ agentQ's Profile: http://www.unicyclist.com/profile/13021 View this thread: http://www.unicyclist.com/thread/75188 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#3
|
|||
|
|||
tap size for nimbus isis hub threads??
just email or im(if you have gchat or gmail) there are really good also make sure it's the right threads per inch i would not trust a measurement i would get the specs -- colin340 ------------------------------------------------------------------------ colin340's Profile: http://www.unicyclist.com/profile/14925 View this thread: http://www.unicyclist.com/thread/75188 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#4
|
|||
|
|||
tap size for nimbus isis hub threads??
In another post: http://www.unicyclist.com/forums/showthread.php?t=55389 "The ISIS spec allows for the use of either M12 or M15 cranks bolts. Koxx and KH both use M12 crank bolts that have a 1.0mm pitch. So you need a 12mm x 1.0mm pitch tap. Truvativ sells a M12 self extracting CroMo crank bolt set that I used to convert my Koxx cranks to a self extracting setup. I got this idea from using a set of Truvativ ISIS cranks on my Koxx hub (see my avatar). These should fit the KH cranks to make them self extracting." That should answer your question. Jerry -- jtrops ------------------------------------------------------------------------ jtrops's Profile: http://www.unicyclist.com/profile/17262 View this thread: http://www.unicyclist.com/thread/75188 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#5
|
|||
|
|||
tap size for nimbus isis hub threads??
Thanks jerry! That was exactly what I needed to know! -- OneWheelLess sigg ------------------------------------------------------------------------ OneWheelLess's Profile: http://www.unicyclist.com/profile/16793 View this thread: http://www.unicyclist.com/thread/75188 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Retapping (Koxx)ISIS Hub Threads? | Brian O. | Unicycling | 16 | March 17th 08 09:17 AM |
nimbus isis trials or nimbus X? | unikid132 | Unicycling | 16 | February 24th 08 04:50 PM |
Nimbus ISIS v.s KH ISIS Hubs | oneisenough | Unicycling | 50 | November 2nd 07 04:43 PM |
Nimbus II or Nimbus Trials ISIS Splined hub? | brendonv | Unicycling | 15 | August 29th 07 08:24 AM |
Selling FSA slined ISIS BB Italian Threads | Scott Morrison | Marketplace | 0 | April 15th 05 06:42 PM |