|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): http://www.artscyclery.com/learningc...tlebosses.html |
Ads |
#2
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
On Thursday, February 18, 2016 at 6:37:52 AM UTC-8, Andre Jute wrote:
TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): http://www.artscyclery.com/learningc...tlebosses.html Still useful. I wonder what the method is for removing a rivnut without wallowing out the hole. -- Jay Beattie. |
#3
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
jbeattie wrote:
:On Thursday, February 18, 2016 at 6:37:52 AM UTC-8, Andre Jute wrote: : TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): : http://www.artscyclery.com/learningc...tlebosses.html :Still useful. I wonder what the method is for removing a rivnut without wallowing out the hole. Least tooling intensive way is a series of drill bits, starting small, and working up. When the inner part gets thin, it can be deformed and removed or pushed through. If you do it a lot, there are specialized cutters and fixtures to do it in fewer steps. -- sig 38 |
#4
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
On Thursday, February 18, 2016 at 3:31:23 PM UTC, jbeattie wrote:
On Thursday, February 18, 2016 at 6:37:52 AM UTC-8, Andre Jute wrote: TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): http://www.artscyclery.com/learningc...tlebosses.html Still useful. I wonder what the method is for removing a rivnut without wallowing out the hole. -- Jay Beattie. It's for jobs like these that drill bits are sold in sets. Start with a small bit, drill a pilot hole, fit a slightly bigger bit, and so on, until the rivet you want to remove is just a thin shell which you can squeeze with pliers so it comes out without damaging the hole. That's the easy party. The more difficult part is fishing for bits that fell inside that will rattle irritatingly. Andre Jute |
#5
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
On 2/18/2016 10:53 AM, David Scheidt wrote:
jbeattie wrote: :On Thursday, February 18, 2016 at 6:37:52 AM UTC-8, Andre Jute wrote: : TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): : http://www.artscyclery.com/learningc...tlebosses.html :Still useful. I wonder what the method is for removing a rivnut without wallowing out the hole. Least tooling intensive way is a series of drill bits, starting small, and working up. When the inner part gets thin, it can be deformed and removed or pushed through. If you do it a lot, there are specialized cutters and fixtures to do it in fewer steps. See http://electricalequipment.tpub.com/...07-14_34_1.jpg For a bike, that would rely on having the frame tube open at the bottom (say, into the bottom bracket) so the body of the rivnut could be taken out. I wouldn't want one rattling around inside a frame tube as I rode. -- - Frank Krygowski |
#6
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
On Thu, 18 Feb 2016 07:31:19 -0800 (PST), jbeattie
wrote: I wonder what the method is for removing a rivnut without wallowing out the hole. -- Jay Beattie. Use a button head rivet extractor like this: http://www.northerntool.com/shop/tools/product_200451731_200451731 http://www.yardstore.com/browse.cfm/4,4332.html https://www.aircraft-tool.com/shop/detail.aspx?PRODUCT_ID=1341S http://www.browntool.com/Default.aspx?tabid=344&ProductID=154 These are very common among aviation mechanics, where the typical general aviation flying machine is held together with blind rivets. The basic idea is to keep the drill centered in the middle of the rivet or rivnut using the head as a guide. As long as the head is not mutilated, that should work. The rest is picking the correct size drill bit. You're on your own for figuring out how to remove what's left of the rivet and shavings from inside the frame. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#7
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
On 2/18/2016 7:31 AM, jbeattie wrote:
On Thursday, February 18, 2016 at 6:37:52 AM UTC-8, Andre Jute wrote: TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): http://www.artscyclery.com/learningc...tlebosses.html Still useful. I wonder what the method is for removing a rivnut without wallowing out the hole. You grind the top off, let the bottom go into the frame, then shake out the the bottom piece through the seat tube or bottom bracket. Of course you have to be extremely careful when grinding. I'd make a shield out of thin piece of steel, with a hole drilled into it, to prevent the grinding wheel from contacting the frame and I'd do the last little bit with a tiny metal file. Use a small rotary tool for most of the grinding. |
#8
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
On 2/18/2016 7:53 AM, David Scheidt wrote:
jbeattie wrote: :On Thursday, February 18, 2016 at 6:37:52 AM UTC-8, Andre Jute wrote: : TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): : http://www.artscyclery.com/learningc...tlebosses.html :Still useful. I wonder what the method is for removing a rivnut without wallowing out the hole. Least tooling intensive way is a series of drill bits, starting small, and working up. When the inner part gets thin, it can be deformed and removed or pushed through. If you do it a lot, there are specialized cutters and fixtures to do it in fewer steps. That may work for a Rivnut that isn't spinning, but probably not for one that is already loose. For a loose one you grind the top off until you can push the bottom into the frame. Then you shake out the piece in the frame through the bottom bracket or seat tube. |
#9
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
On Thursday, February 18, 2016 at 7:54:00 AM UTC-8, David Scheidt wrote:
jbeattie wrote: :On Thursday, February 18, 2016 at 6:37:52 AM UTC-8, Andre Jute wrote: : TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): : http://www.artscyclery.com/learningc...tlebosses.html :Still useful. I wonder what the method is for removing a rivnut without wallowing out the hole. Least tooling intensive way is a series of drill bits, starting small, and working up. When the inner part gets thin, it can be deformed and removed or pushed through. If you do it a lot, there are specialized cutters and fixtures to do it in fewer steps. This guy does it in a single pass with a right-sized drill bit. It must not enlarge the hole, because when he withdraws the bit, the old rivnut is on it. https://www.youtube.com/watch?v=0gqT...M-ZnkD&index=2 It is not immediately apparent to me how this tool works: https://www.youtube.com/watch?v=-gkY...M-ZnkD&index=5 -- Jay Beattie. |
#10
|
|||
|
|||
How the LBS fixes rivnuts installed by wannabel bike mechanics
On 2/18/2016 4:16 PM, jbeattie wrote:
On Thursday, February 18, 2016 at 7:54:00 AM UTC-8, David Scheidt wrote: jbeattie wrote: :On Thursday, February 18, 2016 at 6:37:52 AM UTC-8, Andre Jute wrote: : TROLL BAIT (ONLY ON RBT -- ELSEWHERE CONSIDERED USEFUL INFORMATION): : http://www.artscyclery.com/learningc...tlebosses.html :Still useful. I wonder what the method is for removing a rivnut without wallowing out the hole. Least tooling intensive way is a series of drill bits, starting small, and working up. When the inner part gets thin, it can be deformed and removed or pushed through. If you do it a lot, there are specialized cutters and fixtures to do it in fewer steps. This guy does it in a single pass with a right-sized drill bit. It must not enlarge the hole, because when he withdraws the bit, the old rivnut is on it. https://www.youtube.com/watch?v=0gqT...M-ZnkD&index=2 It is not immediately apparent to me how this tool works: https://www.youtube.com/watch?v=-gkY...M-ZnkD&index=5 -- Jay Beattie. It wasn't clear to me either in the live action version. Try the manufacturer's animation: https://www.youtube.com/watch?v=hJMd...ature=youtu.be it's an EDM process. Probably the best way to deal with a lot of the same rivets in a series, seems excessive for most cyclists' home repairs. -- Andrew Muzi www.yellowjersey.org/ Open every day since 1 April, 1971 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Why auto mechanics are such scoundrels and bike mechanics nice people? | John B. | Techniques | 0 | August 15th 12 02:10 AM |
A program to train young bike mechanics... | spdrecrd | General | 6 | November 3rd 07 02:42 PM |
A program to train young bike mechanics... | Tom Sherman[_2_] | Techniques | 0 | November 3rd 07 02:42 PM |
Oiling every day keeps the bike mechanics away | Micheal Artindale | Mountain Biking | 9 | December 23rd 04 01:14 PM |
YoHost Brett Fixes FREE Bike Classifieds | Cycle America | General | 0 | May 13th 04 08:51 PM |