|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Crank lengh advice needed please.
I've searched the forum and read a lot on crank length, but I'm still unsure what to do so would appreciate some suggestions. I've been learning now for about 2 months and can pretty well ride as far as my legs will allow on flattish bike tracks and the road (no off roading yet) and can successfully freemount about 30% of the time - so overall I'm pretty happy but I feel that now I need to start getting some miles under the wheels to really build up my skill.....however I'm finding that on the flat and smooth I'm just not going as fast as I'd like. Today over a 3 mile ride my max speed was 8.5 mph (legs flying!) but my general comfortable speed was only about 6 mph - which I think is too slow and makes my ride feel a bit unsteady and wobbly. I would like to add at least 2 or 3 mph (or more?) to those speeds but can't figure out what crank length's to get, so all suggestions welcome. The facts a 24" Onza Muni Hookworm tyre 165mm cranks I'm 48 and not as fit as I should be - but getting fitter! -- Splodge ------------------------------------------------------------------------ Splodge's Profile: http://www.unicyclist.com/profile/18158 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
Ads |
#2
|
|||
|
|||
Crank lengh advice needed please.
I have to say that 8.5 mph on a 24" MUni with 165's is impressive. I was in a similar situation and the solution was a 29'er with 125's. Shorter cranks will make spinning much easier, but you will lose a lot of leverage for mounting, braking and controlling speed. I am putting 150's on my Onza MUni, and I suspect they will be a better fit for that kind of riding. I am finding that 8.5-9 mph is a comfortable cruising speed on my 29'er, and that when I really get into the zone I can go good distances at 12mph. I commute to work 4 miles, and it takes 25 minutes, but much of the time loss is due to a 1 mile downhill section that I ride slower. My time is getting better in that section as I get more comfortable using the hand brake. In the end crank length seems to be a fairly personal decision. There are folks on this forum that like long cranks, and some espouse the benefits of really short (89mm) cranks. I hope this doesn't just confuse the issue more. -- jtrops ------------------------------------------------------------------------ jtrops's Profile: http://www.unicyclist.com/profile/17262 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#3
|
|||
|
|||
Crank lengh advice needed please.
I went from 165mm cranks to 150mm cranks, I definitely prefer the 150s. That said, I cannot make any comments about extra speed but I found the 150s did not hurt my knees and the spinning of the pedals seemed smoother (less peddling induced wobble). I live in a hilly area so need long cranks but it could be an idea would be to get the KH Moment 125-150 cranks (if they fit on the Onza). That would give you more options. -- scoope ------------------------------------------------------------------------ scoope's Profile: http://www.unicyclist.com/profile/17710 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#4
|
|||
|
|||
Crank lengh advice needed please.
I swapped from 165s to 150s on my 26" muni a few years ago and I'd never go back. On a 24 I'd say go for 140s, or even try 125s if you're only riding easy flat stuff. (Or get a bigger wheel) Rob -- rob.northcott ------------------------------------------------------------------------ rob.northcott's Profile: http://www.unicyclist.com/profile/7436 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#5
|
|||
|
|||
Crank lengh advice needed please.
A few inches of wheel size will make a much bigger speed difference than a few centimeters of crank length. An extra inch in wheel size adds an extra 3.14 inches to distance per revolution. -- kevinalexandersmith http://www.youtube.com/user/KevinAlexanderSmith ------------------------------------------------------------------------ kevinalexandersmith's Profile: http://www.unicyclist.com/profile/15268 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#6
|
|||
|
|||
Crank lengh advice needed please.
have to add to the genreal consensus, if you're not riding heavily technical and want to go faster a 29er is your best bet, i went down the 140s on a 24" route and although it is noticebaly faster, a 29er is nicer. -- kington99 Dave - what a thoroughly post-modern subversion of the cycling genre - ------------------------------------------------------------------------ kington99's Profile: http://www.unicyclist.com/profile/9417 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#7
|
|||
|
|||
Crank lengh advice needed please.
I have 125 mm cranks on a Nimbus 24" with a hookworm tire, and find it comfortable to ride. I do not go very fast (and I generally have not been measuring my speed) but the leg motion is understated. I have been on a 26" with 165 mm cranks and it feels very strange. There was just so much pumping with my knees to get anywhere! For road riding I would definitely recommend shorter cranks. You will be more comfortable, even with some hills and may get more speed as a bonus. -- scott ttocs ------------------------------------------------------------------------ scott ttocs's Profile: http://www.unicyclist.com/profile/18076 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#8
|
|||
|
|||
Crank lengh advice needed please.
The spin rate doesn't change with shorter cranks, but it may feel smoother and easier to spin. That said, if you want speed then you'll need a larger wheel. For muni, anything shorter than 150 at your skill level is going to make climbing vert diffucult. If you have yet to try muni, I'd stick with the 165's until you learn how to climb on rough terrain, then drop to a 150 after you know what you're doing. Speed is nothing, for that you can ride a bike, try managing that 8.5 mph speed on single track or downhill, that'll work for sure -- Nurse Ben ------------------------------------------------------------------------ Nurse Ben's Profile: http://www.unicyclist.com/profile/17487 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#9
|
|||
|
|||
Crank lengh advice needed please.
Nurse Ben;1149966 wrote: The spin rate doesn't change with shorter cranks, but it may feel smoother and easier to spin. That said, if you want speed then you'll need a larger wheel. For muni, anything shorter than 150 at your skill level is going to make climbing vert diffucult. If you have yet to try muni, I'd stick with the 165's until you learn how to climb on rough terrain, then drop to a 150 after you know what you're doing. Speed is nothing, for that you can ride a bike, try managing that 8.5 mph speed on single track or downhill, that'll work for sure The spin rate does increase with shorter cranks. That's half the reason for going shorter! And as for speed, if you want to go fast, you wouldn't ride a bike either, you'd drive a car. -- GizmoDuck The Induni Unicycle Tour 2009. Unicycle Tour of India. Email me for details. www.induni.adventureunicyclist.com The Uninam Tour 2008.....Hanoi to Saigon!!! www.uninam.net The SINZ Unicycle Tour 2007....South Island, New Zealand www.sinzuni.org ------------------------------------------------------------------------ GizmoDuck's Profile: http://www.unicyclist.com/profile/794 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
#10
|
|||
|
|||
Crank lengh advice needed please.
Good answers everybody - thanks, made me think through my original thoughts. I'm only after more speed to make my ride smoother and feel more controlled, in actual fact the best way to do that is to learn to ride smoother and with more control!! Therefore I figure that I should leave my crank length alone and just do more, and harder, riding on the stuff that gives me a problem. Since starting to ride a Unicycle I've found I like it more than I thought I would - I can feel a collection starting!! -- Splodge ------------------------------------------------------------------------ Splodge's Profile: http://www.unicyclist.com/profile/18158 View this thread: http://www.unicyclist.com/thread/74849 Posted Via Usenet.com Premium Usenet Newsgroup Services ---------------------------------------------------------- http://www.usenet.com |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Disparate spoke lengh problem on American Classic wheel. | Johan Bornman | Techniques | 2 | December 15th 07 05:33 AM |
Advice needed for cranks that use self-extracting crank bolts for Campy 9 spd | Alan | Techniques | 6 | July 6th 05 10:54 PM |
hi - some advice needed! | KoperniK | UK | 13 | May 25th 05 09:47 PM |
Did my 1st TT - advice needed | AC | UK | 13 | July 19th 04 10:06 AM |
1st aid advice needed please | Sofa | Unicycling | 16 | September 15th 03 01:03 AM |