#1
|
|||
|
|||
rear brake rub
I can't figure it out. My Ultegra rear brake on my Raleigh wet weather road
bike rubs the rim no matter what. It's rubbing on the non-drive side, the same side the cable runs on. I have tried: tightening the holding bolt really tightly cleaning the whole thing and reinstalling switching one of the washers on the axle to the other side adding washers to the holding bolts replacing the brake cable shortening the brake cable housing I even tried duct tape. What gives? -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter |
Ads |
#2
|
|||
|
|||
rear brake rub
JF writes
I can't figure it out. My Ultegra rear brake on my Raleigh wet weather road bike rubs the rim no matter what. It's rubbing on the non-drive side, the same side the cable runs on. I have tried: tightening the holding bolt really tightly cleaning the whole thing and reinstalling switching one of the washers on the axle to the other side adding washers to the holding bolts replacing the brake cable shortening the brake cable housing I even tried duct tape. What gives? ...no mention of trouble-shooting the brake lever...just curious. Best Regards - Mike Baldwin |
#3
|
|||
|
|||
rear brake rub
Jim F Wrote: I can't figure it out. My Ultegra rear brake on my Raleigh wet weather road bike rubs the rim no matter what. It's rubbing on the non-drive side, the same side the cable runs on. I have tried: tightening the holding bolt really tightly cleaning the whole thing and reinstalling switching one of the washers on the axle to the other side adding washers to the holding bolts replacing the brake cable shortening the brake cable housing I even tried duct tape. What gives? -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter Try the arch spring tension adjustment... and maybe you will need to recenter the arms as well. http://bike.shimano.com/media/techdo...9830615949.pdf -- daveornee |
#4
|
|||
|
|||
rear brake rub
On Feb 29, 8:28 pm, daveornee daveornee.35k...@no-
mx.forums.cyclingforums.com wrote: Jim F Wrote: I can't figure it out. My Ultegra rear brake on my Raleigh wet weather road bike rubs the rim no matter what. It's rubbing on the non-drive side, the same side the cable runs on. I have tried: tightening the holding bolt really tightly cleaning the whole thing and reinstalling switching one of the washers on the axle to the other side adding washers to the holding bolts replacing the brake cable shortening the brake cable housing I even tried duct tape. What gives? -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter Try the arch spring tension adjustment... and maybe you will need to recenter the arms as well. http://bike.shimano.com/media/techdo.../8DD0A-001_BR-... -- daveornee I had the same issue with an old Trek of mine. The problem for my bike was the axle/brake bridge drilling interface was a hair loose, so it wandered no matter how I tightened and adjusted. I solved the problem with: 1) a slightly larger (hex key) nut which fit the recess more tightly; 2) a star washer on the flat side of the brake bridge; 3) and a homemade thin plastic sleeve wrapped around the axle. I don't know if your bike has the same problem, but I would definitely check. |
#5
|
|||
|
|||
rear brake rub
Michael Baldwin wrote:
JF writes I can't figure it out. My Ultegra rear brake on my Raleigh wet weather road bike rubs the rim no matter what. It's rubbing on the non-drive side, the same side the cable runs on. I have tried: tightening the holding bolt really tightly cleaning the whole thing and reinstalling switching one of the washers on the axle to the other side adding washers to the holding bolts replacing the brake cable shortening the brake cable housing I even tried duct tape. What gives? ..no mention of trouble-shooting the brake lever...just curious. Best Regards - Mike Baldwin i'd start with adjusting the spring adjusting screw which centers the brake! -- /Marten info(apestaartje)m-gineering(punt)nl |
#6
|
|||
|
|||
rear brake rub
"icebike" wrote in message
... On Feb 29, 8:28 pm, daveornee daveornee.35k...@no- mx.forums.cyclingforums.com wrote: Jim F Wrote: I can't figure it out. My Ultegra rear brake on my Raleigh wet weather road bike rubs the rim no matter what. It's rubbing on the non-drive side, the same side the cable runs on. I have tried: tightening the holding bolt really tightly cleaning the whole thing and reinstalling switching one of the washers on the axle to the other side adding washers to the holding bolts replacing the brake cable shortening the brake cable housing I even tried duct tape. What gives? -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter Try the arch spring tension adjustment... and maybe you will need to recenter the arms as well. http://bike.shimano.com/media/techdo.../8DD0A-001_BR-... -- daveornee I had the same issue with an old Trek of mine. The problem for my bike was the axle/brake bridge drilling interface was a hair loose, so it wandered no matter how I tightened and adjusted. I solved the problem with: 1) a slightly larger (hex key) nut which fit the recess more tightly; 2) a star washer on the flat side of the brake bridge; 3) and a homemade thin plastic sleeve wrapped around the axle. I don't know if your bike has the same problem, but I would definitely check. This is annoying. Thanks for the BR-6600 pdf Tech instructions, though daveornee. Very helpful. Unfortunately I am not much better off. I cleaned and reinstalled the brake, along with fresh cable. I replaced the washer on the brake side with a star washer and I thought that would do it. Not quite. No. I should've thought of adjusting the centering adjustment bolt but it hasn't resolved it either. I don't think I can fit a larger hex nut. What would a thin plastic sleeve wrapped around the axle do? Thanks. -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter |
#7
|
|||
|
|||
rear brake rub
On Mar 3, 3:48*pm, "Jim F" wrote:
"icebike" wrote in message ... On Feb 29, 8:28 pm, daveornee daveornee.35k...@no- mx.forums.cyclingforums.com wrote: Jim F Wrote: I can't figure it out. *My Ultegra rear brake on my Raleigh wet weather road bike rubs the rim no matter what. *It's rubbing on the non-drive side, the same side the cable runs on. *I have tried: tightening the holding bolt really tightly cleaning the whole thing and reinstalling switching one of the washers on the axle to the other side adding washers to the holding bolts replacing the brake cable shortening the brake cable housing I even tried duct tape. What gives? -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter Try the arch spring tension adjustment... and maybe you will need to recenter the arms as well. http://bike.shimano.com/media/techdo.../8DD0A-001_BR-... -- daveornee I had the same issue with an old Trek of mine. *The problem for my bike was the axle/brake bridge drilling interface was a hair loose, so it wandered no matter how I tightened and adjusted. *I solved the problem with: 1) a slightly larger (hex key) nut which fit the recess more tightly; 2) a star washer on the flat side of the brake bridge; 3) and a homemade thin plastic sleeve wrapped around the axle. I don't know if your bike has the same problem, but I would definitely check. This is annoying. *Thanks for the BR-6600 pdf Tech instructions, though daveornee. *Very helpful. *Unfortunately I am not much better off. *I cleaned and reinstalled the brake, along with fresh cable. *I replaced the washer on the brake side with a star washer and I thought that would do it.. Not quite. *No. *I should've thought of adjusting the centering adjustment bolt but it hasn't resolved it either. I don't think I can fit a larger hex nut. *What would a thin plastic sleeve wrapped around the axle do? Thanks. -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter- Hide quoted text - - Show quoted text - I assumed you tried adjusting the centering adjustment right off the bat. If you didn't even try that, you might want to take your bike to a more experienced mechanic who can analyse and solve your problem. If you read my post carefully, I stated my brake was slipping because the brake axle and the brake bridge drilling had too much play. I solved it with: 1) hex nut with a slightly wider head (easily found at your local shop which usually has a bin o' loose parts)which fit more tightly with the recessed side of the brake bridge; and 2) a thin plastic sleeve (which reduced the excess play). Again, this worked on my specific situation - don't assume it will solve your own problem. I only offer it up as a possibility. Without actually looking at the bike, everyone is really only guessing at the cause and a solution. This definitely should be a solvable problem, caused by something like a brake bridge face not perpendicular to the axle drilling; or by axle threads that are cut too short and the hex nut is tightening against the axle, but not against the brake bridge. But like I said, we are only guessing. Best of luck. |
#8
|
|||
|
|||
rear brake rub
On Mar 3, 11:41*pm, icebike wrote:
On Mar 3, 3:48*pm, "Jim F" wrote: "icebike" wrote in message ... On Feb 29, 8:28 pm, daveornee daveornee.35k...@no- mx.forums.cyclingforums.com wrote: Jim F Wrote: I can't figure it out. *My Ultegra rear brake on my Raleigh wet weather road bike rubs the rim no matter what. *It's rubbing on the non-drive side, the same side the cable runs on. *I have tried: tightening the holding bolt really tightly cleaning the whole thing and reinstalling switching one of the washers on the axle to the other side adding washers to the holding bolts replacing the brake cable shortening the brake cable housing I even tried duct tape. What gives? -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter Try the arch spring tension adjustment... and maybe you will need to recenter the arms as well. http://bike.shimano.com/media/techdo.../8DD0A-001_BR-.... -- daveornee I had the same issue with an old Trek of mine. *The problem for my bike was the axle/brake bridge drilling interface was a hair loose, so it wandered no matter how I tightened and adjusted. *I solved the problem with: 1) a slightly larger (hex key) nut which fit the recess more tightly; 2) a star washer on the flat side of the brake bridge; 3) and a homemade thin plastic sleeve wrapped around the axle. I don't know if your bike has the same problem, but I would definitely check. This is annoying. *Thanks for the BR-6600 pdf Tech instructions, though daveornee. *Very helpful. *Unfortunately I am not much better off. *I cleaned and reinstalled the brake, along with fresh cable. *I replaced the washer on the brake side with a star washer and I thought that would do it. Not quite. *No. *I should've thought of adjusting the centering adjustment bolt but it hasn't resolved it either. I don't think I can fit a larger hex nut. *What would a thin plastic sleeve wrapped around the axle do? Thanks. -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter- Hide quoted text - - Show quoted text - I assumed you tried adjusting the centering adjustment right off the bat. *If you didn't even try that, you might want to take your bike to a more experienced mechanic who can analyse and solve your problem. If you read my post carefully, I stated my brake was slipping because the brake axle and the brake bridge drilling had too much play. *I solved it with: 1) hex nut with a slightly wider head (easily found at your local shop which usually has a bin o' loose parts)which fit more tightly with the recessed side of the brake bridge; and 2) a thin plastic sleeve (which reduced the excess play). *Again, this worked on my specific situation - don't assume it will solve your own problem. I only offer it up as a possibility. *Without actually looking at the bike, everyone is really only guessing at the cause and a solution. This definitely should be a solvable problem, caused by something like a brake bridge face not perpendicular to the axle drilling; or by axle threads that are cut too short and the hex nut is tightening against the axle, but not against the brake bridge. *But like I said, we are only guessing. *Best of luck.- Hide quoted text - - Show quoted text - Also, Mike Baldwin makes a good point: check your brake lever. Maybe someone forgot to use a housing cap.... |
#9
|
|||
|
|||
rear brake rub
"icebike" wrote in message
... On Mar 3, 11:41 pm, icebike wrote: On Mar 3, 3:48 pm, "Jim F" wrote: "icebike" wrote... I assumed you tried adjusting the centering adjustment right off the bat. If you didn't even try that, you might want to take your bike to a more experienced mechanic who can analyse and solve your problem. If you read my post carefully, I stated my brake was slipping because the brake axle and the brake bridge drilling had too much play. I solved it with: 1) hex nut with a slightly wider head (easily found at your local shop which usually has a bin o' loose parts)which fit more tightly with the recessed side of the brake bridge; and 2) a thin plastic sleeve (which reduced the excess play). Again, this worked on my specific situation - don't assume it will solve your own problem. I only offer it up as a possibility. Without actually looking at the bike, everyone is really only guessing at the cause and a solution. This definitely should be a solvable problem, caused by something like a brake bridge face not perpendicular to the axle drilling; or by axle threads that are cut too short and the hex nut is tightening against the axle, but not against the brake bridge. But like I said, we are only guessing. Best of luck.- Hide quoted text - - Show quoted text - Also, Mike Baldwin makes a good point: check your brake lever. Maybe someone forgot to use a housing cap.... --------------------------------------------------------- How would that make the brake rub? I can always steal my wife's DA brake. -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter |
#10
|
|||
|
|||
rear brake rub
On Mar 4, 8:09*pm, "Jim F" wrote:
"icebike" wrote in message ... On Mar 3, 11:41 pm, icebike wrote: On Mar 3, 3:48 pm, "Jim F" wrote: "icebike" wrote... I assumed you tried adjusting the centering adjustment right off the bat. If you didn't even try that, you might want to take your bike to a more experienced mechanic who can analyse and solve your problem. If you read my post carefully, I stated my brake was slipping because the brake axle and the brake bridge drilling had too much play. I solved it with: 1) hex nut with a slightly wider head (easily found at your local shop which usually has a bin o' loose parts)which fit more tightly with the recessed side of the brake bridge; and 2) a thin plastic sleeve (which reduced the excess play). Again, this worked on my specific situation - don't assume it will solve your own problem. I only offer it up as a possibility. Without actually looking at the bike, everyone is really only guessing at the cause and a solution. This definitely should be a solvable problem, caused by something like a brake bridge face not perpendicular to the axle drilling; or by axle threads that are cut too short and the hex nut is tightening against the axle, but not against the brake bridge. But like I said, we are only guessing. Best of luck.- Hide quoted text - - Show quoted text - Also, Mike Baldwin makes a good point: check your brake lever. *Maybe someone forgot to use a housing cap.... --------------------------------------------------------- How would that make the brake rub? I can always steal my wife's DA brake. -- JF "Here comes the lightening and here comes the thunder. Ride on the storm and take it to the sea. " - Jim Hunter- Hide quoted text - - Show quoted text - Another theory of course: depending on the type of cable stop inherent in the brake lever, the metal coil of the cable can slide out of the outer plastic coating just enough to "shorten" the overall length. But I digress - I'm only blowing smoke without actually looking at the bike and it could easily be a hundred other things. If you are determined to fix it yourself, apply Occam's Razor and a bit of patience. Start with the wheel, then wheel/frame alignment, and work it out systematically. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
changing a rear disk brake to a rim brake | Jeremy Watts[_2_] | Mountain Biking | 4 | November 29th 07 04:22 PM |
converting rear disk brake to block brake | Jeremy Watts[_2_] | Mountain Biking | 4 | October 22nd 07 03:40 PM |
rear fixed brake | lybarra | Techniques | 1 | March 23rd 06 07:22 AM |
Rear Brake Mount | [email protected] | Mountain Biking | 1 | October 19th 05 11:18 AM |
XT V Brake front or rear | Steve Walford | UK | 7 | May 28th 04 08:46 PM |