|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Are there any 1" threaded headsets that fit 1 1/8" headtube?
Hi,
Not sure if I am asking this correctly, but does anyone make a headset that fits into a 1 1/8" head tube that allows the use of a 1" threaded fork? Thanks! Lyle |
Ads |
#2
|
|||
|
|||
Are there any 1" threaded headsets that fit 1 1/8" headtube?
res09c5t wrote:
Hi, Not sure if I am asking this correctly, but does anyone make a headset that fits into a 1 1/8" head tube that allows the use of a 1" threaded fork? See: http://harriscyclery.net/site/page.c...&Category=1321 Sheldon "Devolution" Brown +-----------------------------------------------+ | I’m appearing as Preposteros in | | Gilbert & Sullivan's Thespis at M.I.T. | | April 9-10,15-17 http://web.mit.edu/gsp/www | | http://sheldonbrown.com/music.html | | Photos: http://sheldonbrown.org/g-s/thespis | +-----------------------------------------------+ Harris Cyclery, West Newton, Massachusetts Phone 617-244-9772 FAX 617-244-1041 http://harriscyclery.com Hard-to-find parts shipped Worldwide http://captainbike.com http://sheldonbrown.com |
#3
|
|||
|
|||
Are there any 1" threaded headsets that fit 1 1/8" headtube?
Hi,
So these press into the head tube and then the headset presses into them? Do they add much to the stack height? Thanks! Lyle "Sheldon Brown" wrote in message ... res09c5t wrote: Hi, Not sure if I am asking this correctly, but does anyone make a headset that fits into a 1 1/8" head tube that allows the use of a 1" threaded fork? See: http://harriscyclery.net/site/page.c...&Category=1321 Sheldon "Devolution" Brown +-----------------------------------------------+ | I’m appearing as Preposteros in | | Gilbert & Sullivan's Thespis at M.I.T. | | April 9-10,15-17 http://web.mit.edu/gsp/www | | http://sheldonbrown.com/music.html | | Photos: http://sheldonbrown.org/g-s/thespis | +-----------------------------------------------+ Harris Cyclery, West Newton, Massachusetts Phone 617-244-9772 FAX 617-244-1041 http://harriscyclery.com Hard-to-find parts shipped Worldwide http://captainbike.com http://sheldonbrown.com |
#4
|
|||
|
|||
Are there any 1" threaded headsets that fit 1 1/8" headtube?
res09c5t wrote:
Not sure if I am asking this correctly, but does anyone make a headset that fits into a 1 1/8" head tube that allows the use of a 1" threaded fork? There are sleeves to mount one inch format forks and headsets (30.2mm) in 1-1/8 frames. There are sleeves to mount an O/S format Ahead stem on a one inch format fork. There are also sleeves to adapt one inch format (22.2mm) quill stems in O/S ( 25.4) forks. And then again you can buy a headset that's thick enough to accomodate a one inch format fork in an OverSize frame from Chris King. That way you avoid a separate adapter but you end up paying more and it looks and works the same. -- Andrew Muzi www.yellowjersey.org Open every day since 1 April, 1971 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
handlebar height | n crowley | General | 35 | April 19th 04 07:12 PM |
YST threadless headsets | Ian Szekeres | Techniques | 5 | February 25th 04 09:30 AM |
converting threaded to non threaded headset | Dennis Vaughn | Techniques | 9 | October 2nd 03 01:47 PM |
Threaded versus threadless headset | Hjalmar Duklæt | General | 64 | August 29th 03 06:55 PM |
Threaded versus threadless headset | Hjalmar Duklæt | Techniques | 93 | August 28th 03 07:43 AM |