|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
12mm Ambihelical Hex Nuts
On Thu, 26 May 2016 03:45:27 +0000 (UTC), David Scheidt
wrote: Talk to these folks: http://www.eaglefastener.net/technic...ner-table.html They list a 7-19. Bingo. Looks good, if they'll sell small quantities. Thanks. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
Ads |
#23
|
|||
|
|||
12mm Ambihelical Hex Nuts
Jeff Liebermann wrote:
:Now, if you want a real problem, try the double helix screw he :http://802.11junk.com/jeffl/pics/Fluke%208060a/Fluke-screws.jpg :Officially, it's a "High Low Thread Forming Screw". So, how many :threads per inch when there are two different helical threads? Extra Thread pitch doesn't change with number of starts. Lead does, though. Lead is how far the screw advances in a complete rotation. -- sig 28 |
#24
|
|||
|
|||
12mm Ambihelical Hex Nuts
On Thursday, May 26, 2016 at 2:12:51 PM UTC+1, Duane wrote:
On 26/05/2016 9:00 AM, Andre Jute wrote: On Thursday, May 26, 2016 at 1:25:53 PM UTC+1, AMuzi wrote: On 5/25/2016 10:57 PM, Andre Jute wrote: Crocosmia 'Mobius': http://www.sketching.cc/forum3/viewtopic That's a 404 for me. Search finds this instead: http://www.coolmainpress.com/andrepa...ough_6x4in.jpg -- Andrew Muzi www.yellowjersey.org/ Open every day since 1 April, 1971 Thanks, Andrew. I trashed that message as soon as I realized the link didn't work but you were too quick for me. Here's a good link: http://www.sketching.cc/forum3/viewt...osmia#p 18624 Andre Jute These mistakes never happened when Carl Vogel my Googlebug was here Once you put it on usenet it's there forever. I can't see my original message with the wrong link, so It seems to have been wiped when I deleted it; Andrew just saw it in the hour or so during which it was on the net. Andre Jute |
#25
|
|||
|
|||
12mm Ambihelical Hex Nuts
On 5/26/2016 7:18 AM, Jeff Liebermann wrote:
On Thu, 26 May 2016 03:45:27 +0000 (UTC), David Scheidt wrote: Talk to these folks: http://www.eaglefastener.net/technic...ner-table.html They list a 7-19. Bingo. Looks good, if they'll sell small quantities. Thanks. eBay has a lot of these. Search "Hi-Low Thread screws." |
#26
|
|||
|
|||
12mm Ambihelical Hex Nuts
On Thu, 26 May 2016 14:06:00 -0700, sms
wrote: On 5/26/2016 7:18 AM, Jeff Liebermann wrote: On Thu, 26 May 2016 03:45:27 +0000 (UTC), David Scheidt wrote: Talk to these folks: http://www.eaglefastener.net/technic...ner-table.html They list a 7-19. Bingo. Looks good, if they'll sell small quantities. Thanks. eBay has a lot of these. Search "Hi-Low Thread screws." That was the first place I looked. Lots of similar screws: http://www.ebay.com/sch/i.html?_nkw=High-Low+Screw but nothing in #7-19 3/4". -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#27
|
|||
|
|||
12mm Ambihelical Hex Nuts
Frod's rrrrrrr from the XXXXX of the local dealer $100 for the cowl.
BULL ! the ATL IS JUST BEEUTIFULL...THE AIR CLEAN N SALTY...n SpaceX waits for lighter air at 7:30 missing a shot at lull tide. |
#28
|
|||
|
|||
12mm Ambihelical Hex Nuts
Found a set in cadmium from China for
$25 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
cut their nuts off ! | atriage[_6_] | Racing | 0 | November 23rd 12 05:45 PM |
FS: Thomson 130mm x 1.12mm Black Stem | Dawgwalker | Marketplace | 0 | February 4th 07 07:41 PM |
is 15/32 inches near enough to 12mm? | Jim Higson | Techniques | 7 | October 6th 06 09:15 PM |
Torker DX Bearings, 20mm x 40mm x 12mm - Easily Available | pdc | Unicycling | 6 | June 7th 06 02:02 AM |
aw nuts! | muniracer | Unicycling | 18 | January 22nd 04 02:43 AM |