|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
Platform pedal recommendation, please
Jeff Liebermann wrote:
: One side of the pedal works nicely with my 8.5W construction shoes. The other side doesn't. You can guess which side ends up on top most of the time. I'm now shopping for yet another (cheap) replacement. I can sympathise. I have a pair of very nice looking sealed bearing NC-17 pedals which I incautiously mail-ordered without realising that they were not really double sided. They were on special and there was an unaccountable shortage of my favorite MKS's at my usual suppliers. Solved that one, sort of, by bolting a 50mm long piece of 4x16mm flat bar through the front pair of holes meant for reflectors or toe clips. The bike now weighs a few ounces more but the pedals hang vertically when at rest. I contact the correct side of the pedal without looking by a slight rearward motion of the shoe sole, something like flipping a toeclip pedal with the flip tab. PH |
Ads |
#22
|
|||
|
|||
Platform pedal recommendation, please
On Fri, 4 Oct 2013 17:43:02 -0700 (PDT), BCDrums
wrote: Perhaps I don't understand the possible meanings of "platform pedals." I am looking for a pedal with a lot of surface area (...) http://www.motobicycles.com/moto-urban-pedal-en.html http://www.longboardism.com/2013/09/moto-urban-pedal-cycling-industry-gets-inspiration-us.html Long ago, in a land far far away (called Smog Angeles), I inherited a bicycle with a frame that was about 4 cm too tall for me to ride. I couldn't lower the seat any lower. So, I decided to modify the pedals. I found some old pedals, which I disassembled leaving only the stem. I took a 4x4 and center drilled it match the stem diameter. I pounded the bearings from the old pedals into the hole producing the worlds fattest pedals. I added some rubber from an old automobile tire inner tube. The result was ugly, functional, and worked well until I grew somewhat taller. One problem was that I had to be very careful how I positioned my foot on the 4x4 as the pedal wanted to spin out from under my feet. Elevator shoes would probably have worked better, but at that age, not looking like a "dork" was more important than bicycle aesthetics. You probably don't have to go to that extreme. However, attaching a plywood platform onto a conventional cage type pedal only requires a few angle brackets and some fasteners, and will probably do an adequate job of supporting even the largest and flattest feet. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#23
|
|||
|
|||
Platform pedal recommendation, please
On Fri, 4 Oct 2013 17:43:02 -0700 (PDT), BCDrums
wrote: Perhaps I don't understand the possible meanings of "platform pedals." That's like asking "what is the meaning of life". None of the answers make any sense. A good approach (because that's how I do it) is to use pictures. For example, if you're looking for "platform pedals", just inscribe the term into Google Image search, or edit the links below, and Google returns a selection of hopefully appropriate photos: Platform Pedals: https://www.google.com/search?tbm=isch&q=platform+pedals Bear Trap Pedals: https://www.google.com/search?tbm=isch&q=bear+trap+pedals Wide Bicycle Pedals: https://www.google.com/search?tbm=isch&q=wide+bicycle+pedals I usually find the most interesting things using pictures instead of text. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#24
|
|||
|
|||
Platform pedal recommendation, please
Lieb WHAT IS AN AE6KS ? is this tattooed ?
I see urnot cornering in LA ? your saddle is oleless ? in that heat ?on the Republic ? over the San Andreas ? holy coe=w !!! all inhabs of the Republic should sit on holed saddles bicycle or Goat. the hole ACs your testickels and scro Dude ! its coooool. mandatory. also drains for your climate. there's a seatless frame in GooImages under bear trap bicycle pedals...you saw ? next to the bear on trike. Jerry B said Hi over muh bird-seismo field work. Via the quake alert project. I'll send it along for your translation to East Coast. |
#25
|
|||
|
|||
Platform pedal recommendation, please
On Fri, 04 Oct 2013 19:06:22 -0700, Jeff Liebermann
wrote: On Fri, 4 Oct 2013 17:43:02 -0700 (PDT), BCDrums wrote: Perhaps I don't understand the possible meanings of "platform pedals." I am looking for a pedal with a lot of surface area (...) http://www.motobicycles.com/moto-urban-pedal-en.html http://www.longboardism.com/2013/09/moto-urban-pedal-cycling-industry-gets-inspiration-us.html Long ago, in a land far far away (called Smog Angeles), I inherited a bicycle with a frame that was about 4 cm too tall for me to ride. I couldn't lower the seat any lower. So, I decided to modify the pedals. I found some old pedals, which I disassembled leaving only the stem. I took a 4x4 and center drilled it match the stem diameter. I pounded the bearings from the old pedals into the hole producing the worlds fattest pedals. I added some rubber from an old automobile tire inner tube. The result was ugly, functional, and worked well until I grew somewhat taller. One problem was that I had to be very careful how I positioned my foot on the 4x4 as the pedal wanted to spin out from under my feet. Elevator shoes would probably have worked better, but at that age, not looking like a "dork" was more important than bicycle aesthetics. You probably don't have to go to that extreme. However, attaching a plywood platform onto a conventional cage type pedal only requires a few angle brackets and some fasteners, and will probably do an adequate job of supporting even the largest and flattest feet. I've seen blocks, i.e,. square pieces of wood bolted on either side of a pedal - made what looked like a 4 inch cubic pedal - that were apparently sold commercially. Dads used to use them to make the too large bike, that they just bought for Junior, fit well enough that he could sort of ride it :-) -- Cheers, John B. |
#26
|
|||
|
|||
Platform pedal recommendation, please
On Saturday, October 5, 2013 1:43:02 AM UTC+1, BCDrums wrote:
On Friday, October 4, 2013 6:16:23 PM UTC-4, Peter Howard wrote: MKS Sylvan Touring Pedals http://smartbikeparts.com/search_details.php?itm=PD4010 http://www.universalcycles.com/shopp...s.php?id=19660 They are my pedal of choice on several bicycles. Peter, Perhaps I don't understand the possible meanings of "platform pedals." I am looking for a pedal with a lot of surface area, like these: http://www.ergon-bike.com/us/en/product/pc2 or the Redline pedals that AMuzi mentioned. The Sylvans are like the pedals I have now, a quill-type pedal with all weight borne by two thin ridges of metal. I'd like more surface to take the weight, and pins or other ways to create some friction. These MKS pedals are interesting too: http://www.amazon.com/MKS-Lambda-Ped.../dp/B001GSQVEE BC Most of us understood you wanted old-fashioned rubber block pedals, or some modern realization of the same like the Ergons you refer to, pedals suitable for street shoes. But a word you used, "platform", misled careless readers with literal minds. A "platform" is not a utility pedal but a studded MTB speciality like the Lambda which will do your streets shoes' soles no good, nor your shins. By the way. there's another confusing usage. My pedal makeres measure the LENGTH of the pedal parallel to the frame and the WIDTH perpendicular to the frame, so that the length of a pedal can appear to be less than the width.... Check the piccie as well as the specs! Andre Jute |
#27
|
|||
|
|||
Platform pedal recommendation, please
On Saturday, October 5, 2013 7:58:46 AM UTC-4, Andre Jute wrote:
On Saturday, October 5, 2013 1:43:02 AM UTC+1, BCDrums wrote: On Friday, October 4, 2013 6:16:23 PM UTC-4, Peter Howard wrote: MKS Sylvan Touring Pedals http://smartbikeparts.com/search_details.php?itm=PD4010 http://www.universalcycles.com/shopp...s.php?id=19660 They are my pedal of choice on several bicycles. Peter, Perhaps I don't understand the possible meanings of "platform pedals." I am looking for a pedal with a lot of surface area, like these: http://www.ergon-bike.com/us/en/product/pc2 or the Redline pedals that AMuzi mentioned. The Sylvans are like the pedals I have now, a quill-type pedal with all weight borne by two thin ridges of metal. I'd like more surface to take the weight, and pins or other ways to create some friction. These MKS pedals are interesting too: http://www.amazon.com/MKS-Lambda-Ped.../dp/B001GSQVEE BC Most of us understood you wanted old-fashioned rubber block pedals, or some modern realization of the same like the Ergons you refer to, pedals suitable for street shoes. But a word you used, "platform", misled careless readers with literal minds. A "platform" is not a utility pedal but a studded MTB speciality like the Lambda which will do your streets shoes' soles no good, nor your shins. By the way. there's another confusing usage. My pedal makeres measure the LENGTH of the pedal parallel to the frame and the WIDTH perpendicular to the frame, so that the length of a pedal can appear to be less than the width... Check the piccie as well as the specs! Andre Jute we stand corrected for non existent words/concepts....platforms are designed FLAT ie all flat design pedals fall under PLATFORM like this one http://upload.wikimedia.org/wikipedi...ding_pedal.jpg |
#28
|
|||
|
|||
Platform pedal recommendation, please
On Sat, 05 Oct 2013 18:57:30 +0700, John B.
wrote: On Fri, 04 Oct 2013 19:06:22 -0700, Jeff Liebermann wrote: On Fri, 4 Oct 2013 17:43:02 -0700 (PDT), BCDrums wrote: Perhaps I don't understand the possible meanings of "platform pedals." I am looking for a pedal with a lot of surface area (...) http://www.motobicycles.com/moto-urban-pedal-en.html http://www.longboardism.com/2013/09/moto-urban-pedal-cycling-industry-gets-inspiration-us.html Long ago, in a land far far away (called Smog Angeles), I inherited a bicycle with a frame that was about 4 cm too tall for me to ride. I couldn't lower the seat any lower. So, I decided to modify the pedals. I found some old pedals, which I disassembled leaving only the stem. I took a 4x4 and center drilled it match the stem diameter. I pounded the bearings from the old pedals into the hole producing the worlds fattest pedals. I added some rubber from an old automobile tire inner tube. The result was ugly, functional, and worked well until I grew somewhat taller. One problem was that I had to be very careful how I positioned my foot on the 4x4 as the pedal wanted to spin out from under my feet. Elevator shoes would probably have worked better, but at that age, not looking like a "dork" was more important than bicycle aesthetics. You probably don't have to go to that extreme. However, attaching a plywood platform onto a conventional cage type pedal only requires a few angle brackets and some fasteners, and will probably do an adequate job of supporting even the largest and flattest feet. I've seen blocks, i.e,. square pieces of wood bolted on either side of a pedal - made what looked like a 4 inch cubic pedal - that were apparently sold commercially. Dads used to use them to make the too large bike, that they just bought for Junior, fit well enough that he could sort of ride it :-) Dimension Pedal Blocks: http://a248.e.akamai.net/origin-cdn.volusion.com/sb4jw.nuvx9/v/vspfiles/photos/7761062941099-2.jpg http://www.ebay.com/itm/390664941088 I don't recall if those were available in the early 1960's. Looking at the photo, I suspect that it would not have been high enough for me. I was 13 or 14 when I made the wooden pedals. My first prototype was a sandwich something like the photo wrapped in package twine. The problem was that I just couldn't get a good fit or grip to the pedal. So, I eliminated most of the pedal, except for the stem and bearings. I wanted to make it round, but we didn't have a wood lathe. Shoes were a problem. At the time, I was into Florsheim leather sole shoes (with corrective inserts for flat feet). The soles were sufficiently slippery that I could fall on my face just standing on the sidewalk. At least they had a heel, which I could use to position my shoes on the pedal. However, my flat bottom tennis shoes lacked this feature, making tennis shoes a bad idea. I found a pair of golf shoes that almost fit if I wore 3 pairs of socks. I removed most of the cleats except for two that were under the ball of the foot. I drilled matching holes in the wooden pedals. I worked quite well. Unfortunately, my mother failed to appreciate my engineering after I gouged the oak flooring in the house with the cleats. Full disclosu I had some help from my father, who drilled the holes and offered some useful advice. I also managed to cut myself rather badly when trying to adjust the design with a sharp wood chisel. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#29
|
|||
|
|||
Platform pedal recommendation, please
On 10/4/2013 7:43 PM, BCDrums wrote:
On Friday, October 4, 2013 6:16:23 PM UTC-4, Peter Howard wrote: MKS Sylvan Touring Pedals http://smartbikeparts.com/search_details.php?itm=PD4010 http://www.universalcycles.com/shopp...s.php?id=19660 They are my pedal of choice on several bicycles. Peter, Perhaps I don't understand the possible meanings of "platform pedals." I am looking for a pedal with a lot of surface area, like these: http://www.ergon-bike.com/us/en/product/pc2 or the Redline pedals that AMuzi mentioned. The Sylvans are like the pedals I have now, a quill-type pedal with all weight borne by two thin ridges of metal. I'd like more surface to take the weight, and pins or other ways to create some friction. These MKS pedals are interesting too: http://www.amazon.com/MKS-Lambda-Ped.../dp/B001GSQVEE BC I think OP was looking for the style of the two top images he http://www.redlinebicycles.com/components/pedals tough as any you'll find and often selected by the lower orders of abusive riders to great success. -- Andrew Muzi www.yellowjersey.org/ Open every day since 1 April, 1971 |
#30
|
|||
|
|||
Platform pedal recommendation, please
On Saturday, October 5, 2013 11:22:09 AM UTC-4, AMuzi wrote:
I think OP was looking for the style of the two top images he http://www.redlinebicycles.com/components/pedals tough as any you'll find and often selected by the lower orders of abusive riders to great success. Andrew, the Redline is more what I had in mind. Although with all of this discussion of the MKS 3000R Dutch-style pedals, I am wavering: more gription from the Redline, or less shin damage from the MKS? BC Lacerated |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Road Bike Pedal Recommendation? | goldmine848 | Techniques | 20 | August 28th 08 05:52 PM |
Replaceable platform pedal pins. | oxfordrider | Unicycling | 2 | April 14th 06 01:57 AM |
Platform pedal suggestions. | David | Mountain Biking | 8 | January 22nd 05 06:24 AM |
Platform Pedal to cure "hot foot" | Roger Zoul | General | 7 | September 14th 04 11:45 AM |
Non-Lycra shorts & platform pedal shoes | Burning_Ranger | UK | 34 | August 6th 04 09:13 AM |