A Cycling & bikes forum. CycleBanter.com

Go Back   Home » CycleBanter.com forum » rec.bicycles » Techniques
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

ebikes: lots of bad ideas



 
 
Thread Tools Display Modes
  #1  
Old May 28th 08, 04:58 PM posted to rec.bicycles.tech
johns
external usenet poster
 
Posts: 5
Default ebikes: lots of bad ideas

Before I start building my ebike, I'm reading everything I can find
on what is available. So far, I'm learning more about what not to
get ..

1. Front wheel hub motors can generate enough torque
to break the front forks. So that company only
recommends rear-wheel hub motors.
2. Most hub motors .. no matter what their "power
rating" don't have enough torque to pull more than
a 4% grade.
3. Only gear motors ... even low power ones .. can
generate enough torque to pull an 8% grade.
4. ( another group ) .. Gear motors weigh about 35
to 40 pounds. WHAT ???????????
5. Regenerative braking is a joke. To recharge a
battery using RB, you would have to coast downhill
for 20 hours. Ordinarily, RB can return about 3% of
your charge.
6. Hub motors are unsprung weight. They cause a
very uncomfortable ride. The emotor should go up
between the pedals, and drive the chain.
7. Battery ratings are for flat terrain at about 10 mph.
In real life, they get about half their rated milage per
charge.
8. The average finished ebike will weigh more than 60
pounds.
9. Some of the ebike "kits" require machining of your
bikes parts in order to fit. They also require calibration
of the hub motor sensors in order to get the motor to
rotate in the proper direction. These operations can
void your kit warranty.
10. An ebike can save you $20,000.00 over 3 years,
so it is worth the $14,000.00 they are asking for it.

Sounds to me like the ebike has a ways to go.

johns
  #2  
Old May 28th 08, 06:21 PM posted to rec.bicycles.tech
[email protected]
external usenet poster
 
Posts: 1,611
Default ebikes: lots of bad ideas

On May 28, 5:58*pm, johns wrote:
Before I start building my ebike, I'm reading everything I can find
on what is available. So far, I'm learning more about what not to
get ..

1. Front wheel hub motors can generate enough torque
* * to break the front forks. So that company only
* * recommends rear-wheel hub motors.
2. Most hub motors .. no matter what their "power
* * rating" don't have enough torque to pull more than
* * a 4% grade.
3. Only gear motors ... even low power ones .. can
* * generate enough torque to pull an 8% grade.
4. ( another group ) .. Gear motors weigh about 35
* * to 40 pounds. WHAT ???????????
5. Regenerative braking is a joke. To recharge a
* * battery using RB, you would have to coast downhill
* * for 20 hours. Ordinarily, RB can return about 3% of
* * your charge.
6. Hub motors are unsprung weight. They cause a
* * very uncomfortable ride. The emotor should go up
* * between the pedals, and drive the chain.
7. Battery ratings are for flat terrain at about 10 mph.
* * In real life, they get about half their rated milage per
* * charge.
8. The average finished ebike will weigh more than 60
* * pounds.
9. Some of the ebike "kits" require machining of your
* * bikes parts in order to fit. They also require calibration
* * of the hub motor sensors in order to get the motor to
* * rotate in the proper direction. These operations can
* * void your kit warranty.
10. An ebike can save you $20,000.00 over 3 years,
* * *so it is worth the $14,000.00 they are asking for it.

Sounds to me like the ebike has a ways to go.

johns


No wonder I've never seen one.

Joseph
  #3  
Old May 29th 08, 02:26 AM posted to rec.bicycles.tech
clare at snyder dot ontario dot canada
external usenet poster
 
Posts: 87
Default ebikes: lots of bad ideas

On Wed, 28 May 2008 10:21:32 -0700 (PDT),
" wrote:

On May 28, 5:58*pm, johns wrote:
Before I start building my ebike, I'm reading everything I can find
on what is available. So far, I'm learning more about what not to
get ..

1. Front wheel hub motors can generate enough torque
* * to break the front forks. So that company only
* * recommends rear-wheel hub motors.
2. Most hub motors .. no matter what their "power
* * rating" don't have enough torque to pull more than
* * a 4% grade.
3. Only gear motors ... even low power ones .. can
* * generate enough torque to pull an 8% grade.
4. ( another group ) .. Gear motors weigh about 35
* * to 40 pounds. WHAT ???????????
5. Regenerative braking is a joke. To recharge a
* * battery using RB, you would have to coast downhill
* * for 20 hours. Ordinarily, RB can return about 3% of
* * your charge.
6. Hub motors are unsprung weight. They cause a
* * very uncomfortable ride. The emotor should go up
* * between the pedals, and drive the chain.
7. Battery ratings are for flat terrain at about 10 mph.
* * In real life, they get about half their rated milage per
* * charge.
8. The average finished ebike will weigh more than 60
* * pounds.
9. Some of the ebike "kits" require machining of your
* * bikes parts in order to fit. They also require calibration
* * of the hub motor sensors in order to get the motor to
* * rotate in the proper direction. These operations can
* * void your kit warranty.
10. An ebike can save you $20,000.00 over 3 years,
* * *so it is worth the $14,000.00 they are asking for it.

Sounds to me like the ebike has a ways to go.

johns


No wonder I've never seen one.

Joseph



I've got one factory built unit and am building a "homebrew". It will
have 7 speeds and front wheel drive, with 18 or 21 speeds on the rear
"pedal power unit" The geared motor I am using IS a bit heavy - and
the front fork is VERY beefy. NO suspension.

The ebike is here.
** Posted from http://www.teranews.com **
  #4  
Old May 28th 08, 09:03 PM posted to rec.bicycles.tech
DougC
external usenet poster
 
Posts: 1,276
Default ebikes: lots of bad ideas

johns wrote:
Before I start building my ebike, I'm reading everything I can find
on what is available. So far, I'm learning more about what not to
get ..

........

Sounds to me like the ebike has a ways to go.

johns


One thing I noticed right off when I started looking into gas and
electric bicycle engine kits, was that the people with electrics always,
always ended up wishing they could ride longer. During a short test ride
the torque/acceleration can seem impressive, and you usually cannot
explore the limitations of the battery endurance.

With gas engines you can ride all day if you keep pouring gas in. Most
of the gas ones don't do real well up hills either, because they only
allow one drive speed. The Staton/NuVinci setup seems to be the first
that allows variable drive ratios.

A few people have built bikes using the cheap Lifan moped/motorcycle
engines, 50-to-100cc engines that only cost around $300 and come with a
3- or 4-speed transmission. These are usually over legal
displacement/power/top speed limits but the multiple gears totally
eliminates the problem of hillclimbing. And the engine/trans weighs
around 40 lbs.
~

  #5  
Old May 28th 08, 11:35 PM posted to rec.bicycles.tech
johns
external usenet poster
 
Posts: 5
Default ebikes: lots of bad ideas

I rode motorcycles for 20+ years as my only
transportation ... and lived through it :-)
I could ride for days and just camp on the road,
and I never got tired of it. Only reason I stopped
was BMW started producing crap bikes, and
I sure wasn't going back to all that repair and
downtime with any other brand. BMW put garbage
brakes on all their new bikes, and I have a rule
about unsafe motorcycles. Only in the last year
have I even thought about it. There's a small
lightweight touring bike in Europe that looks just
like my old Penton 125cc Enduro. I had the 6-day
bike, and I rode it for a hundred miles in the dirt
in races. It would make a good modern road
bike. Mine got about 65 mpg, and it could have
been tuned down to get more. Only weighed
200 pounds. So, what I'm saying ... if I go
back to a motorcycle, it will be a real bike
with good handling. I'm seeing ebikes that I
think cross the line to emotorcycles ... and
are not safe at all.

johns
  #6  
Old May 29th 08, 02:31 AM posted to rec.bicycles.tech
clare at snyder dot ontario dot canada
external usenet poster
 
Posts: 87
Default ebikes: lots of bad ideas

On Wed, 28 May 2008 15:35:47 -0700 (PDT), johns
wrote:

I rode motorcycles for 20+ years as my only
transportation ... and lived through it :-)
I could ride for days and just camp on the road,
and I never got tired of it. Only reason I stopped
was BMW started producing crap bikes, and
I sure wasn't going back to all that repair and
downtime with any other brand. BMW put garbage
brakes on all their new bikes, and I have a rule
about unsafe motorcycles. Only in the last year
have I even thought about it. There's a small
lightweight touring bike in Europe that looks just
like my old Penton 125cc Enduro. I had the 6-day
bike, and I rode it for a hundred miles in the dirt
in races. It would make a good modern road
bike. Mine got about 65 mpg, and it could have
been tuned down to get more. Only weighed
200 pounds. So, what I'm saying ... if I go
back to a motorcycle, it will be a real bike
with good handling. I'm seeing ebikes that I
think cross the line to emotorcycles ... and
are not safe at all.

johns

A lot of the socalled "e-bikes" I am seeing in Ontario are poorly
disguised electric motor scooters - which you would NEVER pedal in
normal use, and definitely no more than a block.

I sure like my Schwinn/Currie I-Zip from Canadian Tire.
** Posted from http://www.teranews.com **
  #7  
Old May 29th 08, 09:51 AM posted to rec.bicycles.tech
Ted Mittelstaedt
external usenet poster
 
Posts: 69
Default ebikes: lots of bad ideas


"johns" wrote in message
...
I rode motorcycles for 20+ years as my only
transportation ... and lived through it :-)
I could ride for days and just camp on the road,
and I never got tired of it. Only reason I stopped
was BMW started producing crap bikes,


Huh?

I commute 30 miles round trip every day on a 1980
Honda 750 K, up and down a 5% grade hill that's
about 4 miles long. That's a 28 year old bike, sir.

I also have a 1982 750C in the garage as a spare
bike with 78K miles on it.

Still plenty of people running airheads. airheads.org
is what you want.

I missed the law that said you had to buy a new sickle
every year.

Ted


  #8  
Old May 29th 08, 03:36 AM posted to rec.bicycles.tech
[email protected]
external usenet poster
 
Posts: 3,092
Default ebikes: lots of bad ideas

On May 28, 1:03 pm, DougC wrote:
johns wrote:
Before I start building my ebike, I'm reading everything I can find
on what is available. So far, I'm learning more about what not to
get ..


Sounds to me like the ebike has a ways to go.


One thing I noticed right off when I started looking into gas and
electric bicycle engine kits, was that the people with electrics always,
always ended up wishing they could ride longer. During a short test ride
the torque/acceleration can seem impressive, and you usually cannot
explore the limitations of the battery endurance.

With gas engines you can ride all day if you keep pouring gas in. Most
of the gas ones don't do real well up hills either, because they only
allow one drive speed. The Staton/NuVinci setup seems to be the first
that allows variable drive ratios.

A few people have built bikes using the cheap Lifan moped/motorcycle
engines, 50-to-100cc engines that only cost around $300 and come with a
3- or 4-speed transmission. These are usually over legal
displacement/power/top speed limits but the multiple gears totally
eliminates the problem of hillclimbing. And the engine/trans weighs
around 40 lbs.


It seems like at that point, you're getting into
"just buy a moped" territory.

I used to live in a hilly area and knew
some people who got E-bikes or Curries to
commute up the hill to work (elevation gain
800 ft, a real hill). They work for that -
only need a fairly short ride time, twice a day,
power gets you up the hill, but not at car speed.
I preferred riding a much lighter plain old
people-bike, but not everyone wants to get
that much exercise.

However, people who want the ebike to cruise
at high speeds or have a really long range
are basically asking it to be an imitation
moped, scooter, or motorcycle. I doubt
that one can make a decent faux moped without
making it as heavy as a moped, and then it
would probably be better and safer to actually
get a moped. The same goes triple for
motorcycles. Electric scooters could be an
interesting, and quieter, niche.

My pet peeve: people who ride loud gas-powered
"bicycles" on bike paths. Get on the road.

Ben

  #9  
Old May 29th 08, 12:54 AM posted to rec.bicycles.tech
John Tserkezis
external usenet poster
 
Posts: 204
Default ebikes: lots of bad ideas

johns wrote:

Before I start building my ebike, I'm reading everything I can find
on what is available. So far, I'm learning more about what not to
get ..


Similar thing to what I keep telling people when they ponder the idea of hub
motors for assistance.

If you take the typical weight of a hub motor, batteries, and control
assembly, and lose that weight from around your now massive arse, you would
more than make up for it, and it cost a whole lot less than the asking price.

And I want to dispute the saving of $20K over three years. Against what? A
car? You can't compare apples and oranges you know.

Want to compare against another bike? Sure, take that $14K price tag,
donate it, buy Enron shares, burn it, whatever, and you'll save more than that
60 pounds in bike weight in body weight loss, and improvment in health over
the next few years, AND save that in healthcare costs.

Hub motors have their place, but not for those who have functional legs,
heck, even ONE functional leg is enough (seen a fellow commuter amputee who
did it without a damn motor).
--
Linux Registered User # 302622
http://counter.li.org
  #10  
Old May 29th 08, 02:39 AM posted to rec.bicycles.tech
clare at snyder dot ontario dot canada
external usenet poster
 
Posts: 87
Default ebikes: lots of bad ideas

On Thu, 29 May 2008 09:54:38 +1000, John Tserkezis
wrote:

johns wrote:

Before I start building my ebike, I'm reading everything I can find
on what is available. So far, I'm learning more about what not to
get ..


Similar thing to what I keep telling people when they ponder the idea of hub
motors for assistance.

If you take the typical weight of a hub motor, batteries, and control
assembly, and lose that weight from around your now massive arse, you would
more than make up for it, and it cost a whole lot less than the asking price.

And I want to dispute the saving of $20K over three years. Against what? A
car? You can't compare apples and oranges you know.

Want to compare against another bike? Sure, take that $14K price tag,
donate it, buy Enron shares, burn it, whatever, and you'll save more than that
60 pounds in bike weight in body weight loss, and improvment in health over
the next few years, AND save that in healthcare costs.

Hub motors have their place, but not for those who have functional legs,
heck, even ONE functional leg is enough (seen a fellow commuter amputee who
did it without a damn motor).



Some of us "old guys" don't have the legs or the lungs to do the
distance we need to go without assistance - and particularly not
without getting all sweated up on the way to the office. With my
e-bike, I pedal, but not strenuously, for about 18 minutes to get to
the office instead of driving the van for 8 minutes. I get the
exercise I would not get driving, and arrive at work in better shape
than I ever would with my normal bicycle - which has not beed ridden
much over the last several yearsdue to a bad knee, among other things.
To do the trip with my old 21 speed bike would take me half an hour
and I'd arrive sweaty and worn out. There are several pretty good
hills on the route (the main highway is much leveler, but no bikes,
mopeds, e-bikes, pedestrians, etc allowed)

As a kid of about 15, I lost a pedal on a SINGLE SPEED bike 30 miles
from home, and rode it back, up hill and down. I'm not that young any
more!!!!
** Posted from http://www.teranews.com **
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Re.Lots of cycles lots of lids Steve Watkin UK 198 May 4th 07 08:46 AM
Lots of cyclists, lots of lids Pyromancer UK 23 April 28th 07 12:54 AM
vid ideas.... chosen Unicycling 19 September 1st 06 04:34 AM
ideas brockfisher05 Unicycling 8 January 21st 05 10:08 PM
Ideas please dirtylitterboxofferingstospammers UK 11 April 11th 04 11:35 PM


All times are GMT +1. The time now is 11:12 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2023, Jelsoft Enterprises Ltd.
Copyright 2004-2023 CycleBanter.com.
The comments are property of their posters.